WMAN-IF2-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Unsigned32, Integer32, Counter32, Counter64, transmission FROM SNMPv2-SMI SnmpAdminString FROM SNMP-FRAMEWORK-MIB TEXTUAL-CONVENTION, MacAddress, RowStatus, TruthValue, TimeStamp, DateAndTime FROM SNMPv2-TC InetAddressType, InetAddress FROM INET-ADDRESS-MIB OBJECT-GROUP, MODULE-COMPLIANCE, NOTIFICATION-GROUP FROM SNMPv2-CONF ifIndex FROM IF-MIB; wmanIf2Mib MODULE-IDENTITY LAST-UPDATED "200610160000Z" -- October 16, 2006 ORGANIZATION "IEEE 802.16" CONTACT-INFO "WG E-mail: stds-802-16@ieee.org WG Chair: Roger B. Marks Postal: (U.S.) National Institute of Standards and Technology E-mail: r.b.marks@ieee.org TGf Chair: Phillip Barber Postal: Huawei Technologies Co., Ltd E-mail: pbarber@futurewei.com Editor: Joey Chou Postal: Intel Corporation 5000 W. Chandler Blvd, Chandler, AZ 85227, USA E-mail: joey.chou@intel.com" DESCRIPTION "This material is from IEEE Std 802.16i Copyright (c) 2006 IEEE. This MIB Module defines managed objects for Subscriber Station and Base Station based on IEEE Std 802.16-2004 and its amendment IEEE Std 802.16e-2005. The MIB contains managed objects that are common for both fixed and mobile Broadband Wireless Networks." REVISION "200610160000Z" DESCRIPTION "The second revision of WMAN2-IF2-MIB module." REVISION "200605230000Z" DESCRIPTION "The first revision of WMAN-IF2-MIB module that is enhanced to support IEEE 802.16e-2005 standard." ::= { transmission 184 } wmanIf2MibObjects OBJECT IDENTIFIER ::= { wmanIf2Mib 1 } wmanIf2BsObjects OBJECT IDENTIFIER ::= { wmanIf2MibObjects 1 } wmanIf2SsObjects OBJECT IDENTIFIER ::= { wmanIf2MibObjects 2 } wmanIf2CommonObjects OBJECT IDENTIFIER ::= { wmanIf2MibObjects 3 } -- Textual Conventions WmanIf2SfSchedulingType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The scheduling service provided by a SC for an upstream service flow. If the parameter is omitted from an upstream QOS Parameter Set, this object takes the value of bestEffort (2). This parameter must be reported as undefined (1) for downstream QOS Parameter Sets." SYNTAX INTEGER {undefined(1), bestEffort(2), nonRealTimePollingService(3), realTimePollingService(4), reserved(5), unsolicitedGrantService(6)} WmanIf2PhsRuleVerify ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The value of this field indicates to the sending entity whether or not the packet header contents are to be verified prior to performing suppression. If PHSV is enabled, the sender shall compare the bytes in the packet header with the bytes in the PHSF that are to be suppressed as indicated by the PHSM." REFERENCE "Subclause 11.13.19.3.7.5 in IEEE Std 802.16-2004" SYNTAX INTEGER {phsVerifyEnable(0), phsVerifyDisable(1)} WmanIf2ClassifierBitMap ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "A bit of of this object is set to 1 if the parameter indicated by the comment was present in the classifier encoding, and 0 otherwise. Note: that BITS are encoded most significant bit first, so that if e.g. bits 6 and 7 are set, this object is encoded as the octet string '030000'H." REFERENCE "Subclause 11.13.19.3.4 in IEEE Std 802.16-2004" SYNTAX BITS {priority(0), ipTos(1), ipProtocol(2), ipMaskedSrcAddr(3), ipMaskedDestAddr(4), srcPort(5), destPort(6), destMacAddr(7), srcMacAddr(8), ethernetProtocol(9), userPriority(10), vlanId(11), ipv6FlowLabel(12)} WmanIf2SfState ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Defines the state of a service flow." SYNTAX INTEGER {authorized(1), admitted(2), active(3)} WmanIf2ServClassName ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Defines the type of service class name." SYNTAX OCTET STRING (SIZE(2..128)) WmanIf2CsSpecification ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Defines the types of convergence sublayer." REFERENCE "Subclause 11.13.19.1 in IEEE Std 802.16e-2005" SYNTAX INTEGER {reserved(0), packetIpV4(1), packetIpV6(2), packet802dot3Ethernet(3), packet802dot1QVlan(4), packetIpV4Over802dot3(5), packetIpV6Over802dot3(6), packetIpV4Over802dot1Q(7), packetIpV6Over802dot1Q(8), atm(9), packet802dot3EthernetRohcHc(10), packet802dot3EthernetEcrtpHc(11), packetIp2RohcHc(12), packetIp2EcrtpHc(13)} WmanIf2MacVersion ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Version number of IEEE 802.16." SYNTAX INTEGER {ieee802Dot16Of2001(1), ieee802Dot16cOf2002(2), ieee802Dot16aOf2003(3), ieee802Dot16Of2004(4), ieee802Dot16e(5), tbd(6)} WmanIf2CidType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Type of CID." SYNTAX INTEGER (0 .. 65535) WmanIf2DataEncryptAlgId ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Data encryption algorithm identifiers." REFERENCE "Table 375 in IEEE Std 802.16-2004" SYNTAX INTEGER {none(0), des56BitCbcMode(1), aesCcmMode(2)} WmanIf2DataAuthAlgId ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Data authentication algorithm identifiers." REFERENCE "Table 376 in IEEE Std 802.16-2004" SYNTAX INTEGER {noDataAuthentication(0), reserved(1)} WmanIf2TekEncryptAlgId ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "TEK encryption algorithm identifiers." REFERENCE "Table 377 in IEEE Std 802.16-2004" SYNTAX INTEGER {tripleDes128BitKey(1), rsa1024BitKey(2), aes128BitKey(3)} WmanIf2ChannelNumber ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Physical channel number" SYNTAX INTEGER (0 .. 199) WmanIf2OfdmFecCodeType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "FEC code type and modulation type" REFERENCE "Table 356 and Table 362 in IEEE Std 802.16-2004" SYNTAX INTEGER {bpskCc1Over2(0), qpskRsCcCc1Over2(1), qpskRsCcCc3Over4(2), sixteenQamRsCcCc1Over2(3), sixteenQamRsCcCc3Over4(4), sixtyFourQamRsCcCc2Over3(5), sixtyFourQamRsCcCc3Over4(6), qpskBtc1Over2(7), qpskBtc3Over4(8), sixteenQamBtc3Over4(9), sixteenQamBtc4Over5(10), sixtyFourQamBtc2Over3(11), sixtyFourQamBtc5Over6(12), qpskCtc1Over2(13), qpskCtc2Over3(14), qpskCtc3Over4(15), sixteenQamCtc1Over2(16), sixteenQamCtc3Over4(17), sixtyFourQamCtc2Over3(18), sixtyFourQamCtc3Over4(19)} WmanIf2OfdmaFecCodeType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "FEC code type and modulation type" REFERENCE "Table 356 and Table 362 in IEEE Std 802.16-2004" SYNTAX INTEGER {qpskCc1Over2(0), qpskCc3Over4(1), sixteenQamCc1Over2(2), sixteenQamCc3Over4(3), sixtyFourQamCc2Over3(4), sixtyFourQamCc3Over4(5), qpskBtc1Over2(6), qpskBtc2Over3(7), sixteenQamBtc3Over5(8), sixteenQamBtc4Over5(9), sixtyFourQamBtc5Over8(10), sixtyFourQamBtc4Over5(11), qpskCtc1Over2(12), qpskCtc2Over3(13), qpskCtc3Over4(14), sixteenQamCtc1Over2(15), sixteenQamCtc3Over4(16), sixtyFourQamCtc2Over3(17), sixtyFourQamCtc3Over4(18), sixtyFourQamCtc5Over6(19), qpskZtCc1Over2(20), qpskZtCc3Over4(21), sixteenQamZtCc1Over2(22), sixteenQamZtCc3Over4(23), sixtyFourQamZtCc2Over3(24), sixtyFourQamZtCc3Over4(25)} -- Textual convention for capabilities encodings WmanIf2eNumOfCid ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The object of this type shows the number of CIDs that SS can support." REFERENCE "Subclause 11.7.6 in IEEE Std 802.16e-2005" SYNTAX INTEGER (2..65535) WmanIf2ArqSupportType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The object of this type indicates whether the SS support ARQ." REFERENCE "Subclause 11.7.8.1 in IEEE Std 802.16-2004" SYNTAX INTEGER {arqNotSupported(0), arqSupported(1)} WmanIf2MaxDsxFlowType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The object of this type specifies the maximum number of concurrent DSA, DSC, or DSD transactions that may be outstanding." REFERENCE "Subclause 11.7.8.2 in IEEE Std 802.16-2004" SYNTAX INTEGER (0..255) WmanIf2MacCrcSupport ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The object of this type indicates whether or not the SS supports MAC level CRC." REFERENCE "Subclause 11.7.8.3 in IEEE Std 802.16-2004" SYNTAX INTEGER {noMacCrcSupport(0), macCrcSupport(1)} WmanIf2MaxMcaFlowType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The object of this type specifies the maximum number of concurrent MCA transactions that may be outstanding." REFERENCE "Subclause 11.7.8.4 in IEEE Std 802.16-2004" SYNTAX INTEGER (0..255) WmanIf2MaxMcpGroupCid ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The object of this type indicates the maximum number of simultaneous Multicast Polling Groups the SS is capable of belonging to." REFERENCE "Subclause 11.7.8.5 in IEEE Std 802.16-2004" SYNTAX INTEGER (0..255) WmanIf2MaxPkmFlowType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The object of this type specifies the maximum number of concurrent PKM transactions that may be outstanding." REFERENCE "Subclause 11.7.8.6 in IEEE Std 802.16-2004" SYNTAX INTEGER (0..255) WmanIf2AuthPolicyType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The object of this type specifies authorization policy that both SS and BS need to negotiate and synchronize. A bit value of 0 = 'not supported', 1 = 'supported'. If this field is omitted, then both SS and BS shall use the IEEE 802.16 security, constituting X.509 digital certificates and the RSA public key encryption algorithm, as authorization policy." REFERENCE "Subclause 11.7.8.7 in IEEE Std 802.16-2004" SYNTAX BITS {ieee802Dot16PrivacySupported(0), reserved1(1), reserved2(2), reserved3(3), reserved4(4), reserved5(5), reserved6(6), reserved7(7)} WmanIf2MaxNumOfSaType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This field specifies maximum number of supported security association of the SS." REFERENCE "Subclause 11.7.8.8 in IEEE Std 802.16-2004" SYNTAX INTEGER (0..255) WmanIf2IpVersionType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The object of this type indicates the version of IP used on the Secondary Management Connection. The valus should be undefined if the 2nd management CID doesn't exist." REFERENCE "Subclause 11.7.4 in IEEE Std 802.16-2004" SYNTAX INTEGER {undefined(0), ipv4(1), ipv6(2)} WmanIf2MacCsBitMap ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The object of this type indicates the set of MAC convergence sublayer support. When a bit is set, it indicates the corresponding CS feature is supported." REFERENCE "Subclause 11.7.7.1 in IEEE Std 802.16e-2005" SYNTAX BITS {atm(0), packetIpv4(1), packetIpv6(2), packet802Dot3(3), packet802Dot1Q(4), packetIpv4Over802Dot3(5), packetIpv6Over802Dot3(6), packetIpv4Over802Dot1Q(7), packetIpv6Over802Dot1Q(8), packet802dot3EthernetRohcHc(9), packet802dot3EthernetEcrtpHc(10), packetIpv4Orv6RohcHc(11), packetIpv4Orv6EcrtpHc(12)} WmanIf2MaxClassifiers ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The object of this type indicates the maximum number of admitted Classifiers that the SS is allowed to have." REFERENCE "Subclause 11.7.7.2 in IEEE Std 802.16-2004" SYNTAX INTEGER (0..65535) WmanIf2PhsSupportType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The object of this type indicates the level of PHS support." REFERENCE "Subclause 11.7.7.3 in IEEE Std 802.16e-2005" SYNTAX INTEGER {noPhsSupport(0), atmPhsSupport(1), packetPhsSupport(2), atmAndPacketPhsSupport(3)} WmanIf2BwAllocSupport ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This field indicates properties of the SS that the BS needs to know for bandwidth allocation purposes. When a bit is set, it indicates the corresponding feature is supported. All unspecified and reserved bits should be set to zero." REFERENCE "Subclause 11.8.1 in IEEE Std 802.16-2004" SYNTAX BITS {reserved(0), halfDuplexFdd(1), fullDuplexFdd(2)} WmanIf2PduConstruction ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Specifies capabilities for construction and transmission of MAC PDUs. When piggybackedRequests bit is set, it indicates that the piggybacked requests are supported. The fsnValuesSize bit is coded as follows: 0 - only 3-bit FSN values are supported 1 - only 11-bit FSN values are supported All unspecified and reserved bits should be set to zero." REFERENCE "Subclause 11.8.2 in IEEE Std 802.16e-2005" SYNTAX BITS {piggybackedRequests(0), fsnValuesSize(1)} WmanIf2SsTransitionGap ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This field indicates the transition speed SSTTG and SSRTG for TDD and H-FDD SSs. Allowed values are: OFDM mode: TDD and H-FDD 0..100 Other modes: TDD: 0..50; H-FDD: 0..100" REFERENCE "Subclause 11.8.3.1 in IEEE Std 802.16-2004" SYNTAX INTEGER (0..100) WmanIf2MaxTxPowerType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This type is used to define maximum available power for BPSK, QPSK, 16-QAM and 64-QAM constellations. The maximum power parameters are reported in dBm and quantized in 0.5 dBm steps ranging from -64 dBm (encoded 0x00) to 63.5 dBm (encoded 0xFF). Values outside this range shall be assigned the closest extreme. SSs that do not support QAM64 shall report the value of 0x00 in the maximum QAM64 power field." REFERENCE "Subclause 11.8.3.2 in IEEE Std 802.16-2004" SYNTAX INTEGER (0..255) WmanIf2OfdmFftSizes ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This field indicates the FFT sizes supported by the SS. For each FFT size, a bit value of 0 indicates 'not supported' while 1 indicates 'supported'." REFERENCE "Subclause 11.8.3.6.1 in IEEE 802.16-2004" SYNTAX BITS {fft256(0), fft2048(1)} WmanIf2OfdmSsDeModType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This field indicates the different demodulator options supported by a WirelessMAN-OFDM PHY SS for downlink. This field is not used for other PHY specifications. A bit value of 0 indicates 'not supported' while 1 indicates 'supported'." REFERENCE "Subclause 11.8.3.6.2 in IEEE Std 802.16e-2005" SYNTAX BITS {qam64(0), btc(1), ctc(2), stc(3), aas(4), subchannelization(5)} WmanIf2OfdmSsModType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This field indicates the different modulator options supported by a WirelessMAN-OFDM PHY SS for uplink. This field is not used for other PHY specifications. A bit value of 0 indicates 'not supported' while 1 indicates 'supported'." REFERENCE "Subclause 11.8.3.6.3 in IEEE Std 802.16e-2005" SYNTAX BITS {qam64(0), btc(1), ctc(2), subchanellization(3), focusedCtBwReq(4), ulCyclicDelay(5)} WmanIf2OfdmFocusedCt ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This field indicates whether the SS supports Focused Contention (see 8.3.7.3.3). A bit value of 0 indicates 'not supported' while 1 indicates 'supported'." REFERENCE "Subclause 11.8.3.6.4 in IEEE Std 802.16-2004" SYNTAX BITS {focusedCtSupport(0)} WmanIf2OfdmTcSublayer ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This field indicates whether or not the SS supports the TC sublayer (see 8.3.4). A bit value of 0 indicates 'not supported' while 1 indicates 'supported'." REFERENCE "Subclause 11.8.3.6.5 in IEEE Std 802.16-2004" SYNTAX BITS {tcSublayerSupport(0)} WmanIf2eOfdmPrivMap ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This field indicates if the private map parameters is supported. A bit value of 0 indicates 'not supported' while 1 indicates 'supported'." REFERENCE "Subclause 11.8.3.6.6 in IEEE Std 802.16e-2005" SYNTAX BITS {regularMap(0), compressedMap(1)} WmanIf2eOfdmUlPower ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This field indicates the uplink power control options supported by a WirelessMAN-OFDM PHY SS for uplink transmission. A bit value of 0 indicates 'not supported' while 1 indicates 'supported'." REFERENCE "Subclause 11.8.3.7.10 in IEEE Std 802.16e-2005" SYNTAX BITS {ulOpenLoopPwrCntl(0), ulAasPreamblePwrCntl(1)} WmanIf2BsIdType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Defines the encoding of BSID. The BSID is a 6 byte number and follows the encoding rules of MacAddress textual convention, i.e. as if it were transmitted least-significant bit first. The value should be displayed with 2 parts clearly separated by a colon e.g: 001DFF:00003A. The most significant part is representing the Operator ID. " SYNTAX OCTET STRING (SIZE(6)) WmanIf2Ipv6FlowLabel ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The value of this field specifies the matching values for the IPv6 Flow label field. As the flow label field has a length of 20 bits, the first 4 bits of the most significant byte shall be set to 0x0 and disregarded." SYNTAX OCTET STRING (SIZE(3)) WmanIf2OfdmaFftSizes ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This field indicates the FFT sizes supported by the SS/MS. For each FFT size, a bit value of 0 indicates 'not supported' while 1 indicates 'supported'." REFERENCE "Subclause 11.8.3.7.1 in IEEE 802.16e-2005" SYNTAX BITS {fft256(0), fft2048(1), fft128(2), fft512(3), fft1024(4)} WmanIf2OfdmaMsDeModType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This field indicates the different demodulator options supported by a WirelessMAN-OFDMA PHY SS for downlink. A bit value of 0 indicates 'not supported' while 1 indicates 'supported'." REFERENCE "Subclause 11.8.3.7.2 in IEEE Std 802.16e-2005" SYNTAX BITS {qam64(0), btc(1), ctc(2), stc(3), ccWithInterleacer(4), harqChase(5), harqCtcIr(6), reserved(7), harqCcIr(8), ldpc(9), dedicatedPilots(10)} WmanIf2OfdmaMsModType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This field indicates the different modulator options supported by a WirelessMAN-OFDMA PHY SS for uplink. A bit value of 0 indicates 'not supported' while 1 indicates 'supported'." REFERENCE "Subclause 11.8.3.7.3 in IEEE Std 802.16e-2005" SYNTAX BITS {qam64(0), btc(1), ctc(2), stc(3), harqChase(4), ctcIr(5), ccIr(6), ldpc(7)} WmanIf2OfdmaPermutation ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This field indicates the OFDMA SS Permutation support A bit value of 0 indicates 'not supported' while 1 indicates 'supported'." REFERENCE "Subclause 11.8.3.7.4 in IEEE 802.16e" SYNTAX BITS {optionalPuscSupport(0), optionalFuscSupport(1), amcOneBySixSupport(2), amcTwoByThreeSupport(3), amcThreeByTwoSupport(4), amcSupportWithHarqMap(5), tusc1Support(6), tusc2Support(7)} WmanIf2eOfdmaDemMimo ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This field indicates the MIMO capability of OFDMA MS demodulator. A bit value of 0 indicates 'not supported' while 1 indicates 'supported'." REFERENCE "Subclause 11.8.3.7.5 in IEEE 802.16e" SYNTAX BITS {twoAntStcMatrixA(0), twoAntStcMatrixBVCoding(1), twoAntStcMatrixBHCoding(2), fourAntStcMatrixA(3), fourAntStcMatrixBVCoding(4), fourAntStcMatrixBHCoding(5), fourAntStcMatrixCVCoding(6), fourAntStcMatrixCHCodingt(7)} WmanIf2eOfdmaMimoCap ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This field indicates the MIMO capability of OFDMA MS demodulator." REFERENCE "Subclause 11.8.3.7.5 in IEEE 802.16e" SYNTAX BITS {twoAntStcMatrixA(0), twoAntStcMatrixBVCoding(1), fourRxAntenna(2), fourAntStcMatrixA(3), fourAntStcMatrixBVCoding(4), fourAntStcMatrixBHCoding(5), fourAntStcMatrixCVCoding(6), fourAntStcMatrixCHCodingt(7), threeAntStcMatrixA(8), threeAntStcMatrixB(9), threeAntStcMatrixCVCoding(10), threeAntStcMatrixCHCodingt(11), calculatingPrecodingWeight(12), adaptiveRateControl(13), calculatingChannelMatrix(14), antennaGrouping(15), antennaSelection(16), codebookBasedPrecoding(17), longTermPrecoding(18), mimoMidamble(19)} WmanIf2eOfdmaUlMimo ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This field indicates the different MIMO options supported by a WirelessMAN-OFDMA PHY SS in the uplink. A bit value of 0 indicates 'not supported' while 1 indicates 'supported'." REFERENCE "Subclause 11.8.3.7.6 in IEEE 802.16e" SYNTAX BITS {twoAntSttd(0), twoAntSmVCoding(1), oneAntCooperativeSm(2)} WmanIf2eOfdmaPrivMap ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This field indicates the AAS private map parameters supported by a WirelessMAN-OFDMA SS. A bit value of 0 indicates 'not supported' while 1 indicates 'supported' for most bits, except chainConcurrency0, chainConcurrency1 that indicates how many parallel private map chains can be supported by an SS. 0: no limit 1..3: maximum concurrent private map chains" REFERENCE "Subclause 11.8.3.7.7 in IEEE Std 802.16e-2005" SYNTAX BITS {harqMap(0), privMap(1), reducedPrivMap(2), privMapChainEnable(3), privMapDlFrameOffset(4), privMapUlFrameOffset(5), chainConcurrency0(6), chainConcurrency1(7)} WmanIf2eOfdmaAasCap ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This field indicates the different AAS options supported by a WirelessMAN-OFDMA PHY SS in the downlink. A bit value of 0 indicates 'not supported' while 1 indicates 'supported' for most bits." REFERENCE "Subclause 11.8.3.7.8 in IEEE Std 802.16e-2005" SYNTAX BITS {aasZone(0), aasDiversityMapScan(1), aasFbckRsp(2), dlAasPreamble(3), ulAasPreamble(4)} WmanIf2eOfdmaCinrCap ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This field indicates the CINR measurement capability supported by a WirelessMAN-OFDMA PHY SS in the downlink. A bit value of 0 indicates 'not supported' while 1 indicates 'supported'." REFERENCE "Subclause 11.8.3.7.9 in IEEE Std 802.16e-2005" SYNTAX BITS {phyCinrPreamble(0), phyCinrPilotSubc(1), phyCinrDataSubc(2), effectiveCinrPreamble(3), effectiveCinrPilotSubc(4), effectiveCinrDataSubc(5), twoCqiChannel(6), freqSelectivityReport(7)} WmanIf2eOfdmaUlPower ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This field indicates the power control options supported by a WirelessMAN-OFDMA PHY SS for uplink transmission. A bit value of 0 indicates 'not supported' while 1 indicates 'supported'." REFERENCE "Subclause 11.8.3.7.11 in IEEE Std 802.16e-2005" SYNTAX BITS {ulOpenLoopPwrCntl(0), ulAasPreamblePwrCntl(1)} WmanIf2eOfdmaMapCap ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This field indicates the different MAP options supported by a WirelessMAN-OFDMA PHY SS. A bit value of 0 indicates 'not supported' while 1 indicates 'supported'." REFERENCE "Subclause 11.8.3.7.12 in IEEE Std 802.16e-2005" SYNTAX BITS {harqMap(0), extendedHarqIe(1), subMapFor1stZone(2), subMapForOtherZone(3), dlRegionDefinition(4)} WmanIf2eOfdmaUlCntlCh ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This field indicates different uplink control channels supported by a WirelessMAN-OFDMA PHY SS. A bit value of 0 indicates 'not supported' while 1 indicates 'supported'." REFERENCE "Subclause 11.8.3.7.13 in IEEE Std 802.16e-2005" SYNTAX BITS {threeBitMimoFastFeedback(0), enhancedFastFeedback(1), ulAck(2), reserved(3), uepFastFeedback(4), fastDlMeasurementFeedback(5), priSecFastFeedback(6), diucCqiFastFeedback(7)} WmanIf2eOfdmaMsCistCap ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This field indicates MS capability of supporting CSIT (uplink sounding). A bit value of 0 indicates 'not supported' while 1 indicates 'supported'. Bits 3..5: Time needed for SS to respond to a sounding command transmitted by the BS 000 0.5ms 001 0.75ms 010 1ms 011 1.25ms 100 1.5ms 101 min(2ms, Next Frame) 110 min(5ms, Next Frame) 111 Next Frame Bits 6..9: Max number of simultaneous sounding instructions (0 = unlimited)" REFERENCE "Subclause 11.8.3.7.14 in IEEE Std 802.16e-2005" SYNTAX BITS {csitTypeA(0), csitTypeB(1), powerAssignment(2), soundingRspTime0(3), soundingRspTime1(4), soundingRspTime2(5), maxSimuSoundInst0(6), maxSimuSoundInst1(7), maxSimuSoundInst2(8), maxSimuSoundInst3(9), noP9Or18ForCsitTypeA(10), csitNotSupported(11)} WmanIf2eOfdmaMaxHarq ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This field indicates the maximum number of UL/DL HARQ burst allocations for the SS in a single UL/DL subframe. Bits 0..2: Maximum number of UL HARQ bursts per HARQ enabled MS per frame 0b000 = 1 (default) Bit 3: Indicates whether the maximum number of UL HARQ bursts per frame in bits 0-2 includes the one Non-HARQ burst. 0 = not included (default) 1 = included Bits 4..7: Maximum number of DL HARQ bursts per HARQ enabled MS per frame. 0b0000 = 1 (default)" REFERENCE "Subclause 11.8.3.7.15 in IEEE Std 802.16e-2005" SYNTAX BITS {maxUlHarqBurst0(0), maxUlHarqBurst1(1), maxUlHarqBurst2(2), nonHarqBurstInUl(3), maxDlHarqBurst0(4), maxDlHarqBurst1(5), maxDlHarqBurst2(6), maxDlHarqBurst3(7)} WmanIf2eOfdmaModMimo ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This field indicates the MIMO capability of OFDMA SS modulator. A bit value of 0 indicates 'not supported' while 1 indicates 'supported'" REFERENCE "Subclause 11.8.3.7.16 in IEEE Std 802.16e-2005" SYNTAX BITS {twoTxAntenna(0), txDiversity(1), spatialMultiplexing(2), beamforming(3), adaptiveRateControl(4), singleAntenna(5), twoAntenna(6)} WmanIf2eSdmaPilotCap ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This field indicates SDMA pilot pattern support for AMC zone." REFERENCE "Subclause 11.8.3.7.17 in IEEE Std 802.16e-2005" SYNTAX INTEGER {noSupport(0), sdmaPilotAandB(1), allSdmaPilotPatterns(2)} WmanIf2eMultiBurst ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This field indicates whether multiple FEC types are supported in DL/UL burst profiles. A bit value of 0 indicates 'not supported' while 1 indicates 'supported'" REFERENCE "Subclause 11.8.3.7.18 in IEEE Std 802.16e-2005" SYNTAX INTEGER {dlWithMultiFecType(0), ulWithMultiFecType(1)} WmanIf2eIncrHarqBuf ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This field indicates the maximal number of data bits the SS is able to use for buffering for NEP/NSCH based incremental redundancy CTC in downlink and uplink transmissions. Bits 0..3: NEP value indicating downlink HARQ buffering capability for incremental redundancy CTC Bit 4: Aggregation Flag for DL 0 = the number of bits is counted separately for each channel 1 = buffering capability may be shared between channels Bits 5..7: reserved Bits 8..11: NEP value indicating uplink HARQ buffering capability for incremental redundancy CTC Bit 12: Aggregation Flag for UL 0 = the number of bits is counted separately for each channel 1 = buffering capability may be shared between channels" REFERENCE "Subclause 11.8.3.7.19 in IEEE Std 802.16e-2005" SYNTAX INTEGER {dlNep0(0), dlNep1(1), dlNep2(2), dlNep3(3), dlAggFlag(4), reserved0(5), reserved1(6), reserved2(7), ulNep0(8), ulNep1(9), ulNep2(10), ulNep3(11), ulAggFlag(12)} WmanIf2eChaseHarqBuf ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This field indicates the maximal number of data bits the SS is able to use for buffering for DIUC/duration based HARQ methods (Chase combining and CC-IR)in downlink and uplink transmissions. Bits 0..5: Downlink HARQ buffering capability for chase combining (K) Bit 6: Aggregation Flag for DL 0 = the number of bits is counted separately for each channel 1 = buffering capability may be shared between channels Bits 7: reserved Bits 8..13: Uplink HARQ buffering capability for chase combining (K) Bit 14: Aggregation Flag for UL 0 = the number of bits is counted separately for each channel 1 = buffering capability may be shared between channels" REFERENCE "Subclause 11.8.3.7.19 in IEEE Std 802.16e-2005" SYNTAX INTEGER {dlChaseComb0(0), dlChaseComb1(1), dlChaseComb2(2), dlChaseComb3(3), dlChaseComb4(4), dlChaseComb5(5), dlAggFlag(6), reserved(7), ulChaseComb0(8), ulChaseComb1(9), ulChaseComb2(10), ulChaseComb3(11), ulChaseComb4(12), ulChaseComb5(13), ulAggFlag(14)} WmanIf2eOfdmaMobility ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This field indicates whether or not the MS supports mobility hand-over, Sleepmode, and Idle-mode. A bit value of 0 indicates 'not supported' while 1 indicates it is supported." REFERENCE "Subclause 11.8.3.7.5 in IEEE 802.16e" SYNTAX BITS {handoverSupport(0), sleepModeSupport(1), idleModeSupport(2)} WmanIf2PsClassId ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Indicates the index to Power Saving Classes. The ID shall be unique within the group of Power Saving Classes associated with the MS. This ID may be used in further MOB_SLP-REQ/RSP messages for activation / deactivation of Power Saving Class." REFERENCE "Subclause 6.3.2.3.44 in IEEE Std 802.16e-2005" SYNTAX INTEGER (0..63) WmanIf2ePsClassType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The types of power saving classes." REFERENCE "Table 374a in IEEE Std 802.16e-2005" SYNTAX INTEGER {powerSavingClassTypeI(1), powerSavingClassTypeII(2), powerSavingClassTypeIII(3)} WmanIf2ePsClassCidDir ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The direction of power saving class's CIDs. 0b00 = Unspecified. Each CID has its own direction assign in its connection creation. Can be DL, UL, or both (in the case of management connections). 0b01 = Downlink direction only. 0b10 = Uplink direction only." REFERENCE "Subclause 6.3.2.3.44 in IEEE Std 802.16e-2005" SYNTAX INTEGER {unspecified(0), downlink(1), uplink(2)} WmanIf2PowerSavingMode ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Power saving class mode active or not active." REFERENCE "Subclause 6.3.2.3.44 in IEEE Std 802.16e-2005" SYNTAX INTEGER {psNotActive(0), psActive(1)} WmanIf2eMaxMacLevel ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "maximum amount of MAC level data including MAC headers and HARQ retransmission bursts the MS is capable of processing in the DL/UL part of a single MAC frame." REFERENCE "Subclause 11.7.8.10 in IEEE Std 802.16e-2005" SYNTAX INTEGER (0..65535) WmanIf2ePackingSupport ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Indicates the availability of MS support for Packing" REFERENCE "Subclause 11.7.8.11 in IEEE Std 802.16e-2005" SYNTAX INTEGER {noPackingSupport(0), packingSupported(1)} WmanIf2eExtRtpsSupport ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Indicates the availability of MS support for Extended rtPS." REFERENCE "Subclause 11.7.8.12 in IEEE Std 802.16e-2005" SYNTAX INTEGER {noExtendedRtpsSupport(0), extendedRtpsSupported(1)} WmanIf2eIpAllocMethod ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Indicates the method of allocating IP address for the secondary management connection. A bit value of 0 indicates 'not supported' while 1 indicates 'supported'." REFERENCE "Subclause 11.7.8.11 in IEEE Std 802.16e-2005" SYNTAX BITS {dhcp(0), mobileIpv4(1), dhcpV6(2), ipv6Autoconfig(3)} WmanIf2eHandoverType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Indicates what type(s) of Handover the BS and the MS supports. bit#0: when it is set to 1, MDHO/FBSS HO not supported. the BS shall ignore all other bits. bit#1: when it is set to 1, FBSS/MDHO DL RF Combining is supported with monitoring MAPs from active BSs bit#2: when it is set to 1, MDHO DL soft Combining is supported with monitoring single MAP from anchor BS bit#3: when it is set to 1, MDHO DL soft combining is supported with monitoring MAPs from active BSs bit#3: when it is set to 1, MDHO UL Multiple transmission is supported" REFERENCE "Subclause 11.7.8.12 in IEEE Std 802.16e-2005" SYNTAX BITS {mdhcFbssHoNotSpported(0), mdhcFbssDlMapsFromActiveBss(1), mdhcDlMapFromAnchorBs(2), mdhcDlMapsFromActiveBss(3), mdhcUlMultipleTx(4)} WmanIf2eArqAckType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Specifies the ARQ ACK type supported by the MS." REFERENCE "Subclause 11.7.23 in IEEE Std 802.16e-2005" SYNTAX BITS {selectiveAck(0), cumulativeAck(1), cumWithSelAck(2), cumWithBlockSeqAck(3)} WmanIf2eMacHeaderSupp ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Indicates whether or not the MS and BS support various types of MAC header and extended subheaders. A bit value of 0 indicates 'not supported', while 1 indicates 'supported'. Bits 8-10: parameters of SDU_SN extended subheader that represent the period of SDU_SN transmission for connection with ARQ disabled = once every 2^p MAC PDUs." REFERENCE "Subclause 11.7.25 in IEEE Std 802.16e-2005" SYNTAX BITS {bwReqUlTxPowerReport(0), bwReqCinrReport(1), cqichAlloationReq(2), phyChannelReport(3), bwReqUlSleepCntl(4), snReport(5), feedbackReport(6), sduSn(7), sdnSnPeriod0(8), sdnSnPeriod1(9), sdnSnPeriod2(10), dlSleepControl(11), feedbackRequest(12), mimcModeFeedback(13), ulTxPowerReport(14), miniFeedback(15), snRequest(16), shortPduSn(17), longPduSn(18)} WmanIf2eHarqAckDelay ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "HARQ ACK delay for DL burst 1 = one frame offset 2 = two frames offset 3 = three frames offset" REFERENCE "Table 353 in IEEE Std 802.16e-2005" SYNTAX INTEGER {oneframeoffset(1), twoframesoffset(2), threeframesoffset(3)} WmanIf2eAasBeamSel ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Boolean to indicate whether unsolicited AAS Beam Select messages (see 6.3.2.3.41 in IEEE 802.16e-2005) should be sent by the MS. 0: MS should not send AAS Beam Select Messages 1: MS may send AAS Beam Select Messages" REFERENCE "Table 353 in IEEE Std 802.16e-2005" SYNTAX INTEGER {notAllowed(0), allowed(1)} -- -- BS object group – containing tables and objects to be implemented in -- the Base station -- -- wmanIf2BsPacketCs contain the Base Station Packet Convergence -- Sublayer objects -- wmanIf2BsPacketCs OBJECT IDENTIFIER ::= { wmanIf2BsObjects 1 } wmanIf2BsProvisionedSfTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2BsProvisionedSfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains service flow profiles provisioned by NMS. The service flow should be created with SS(s) following instruction given by wmanIf2BsSfState object. 1. The QoS parameters of the service flow are provisioned in wmanIf2BsServiceClassTable and referenced by wmanIf2BsServiceClassIndex. 2. The classifier rules of the service flow are provisioned in wmanIf2BsClassifierRuleTable, where they refer to SF via wmanIf2BsSfId. The MAC addresses of SSs the service flow is created with are provisioned in wmanIf2BsSsProvisionedForSfTable, where they refer to SF via wmanIf2BsSfId." REFERENCE "Subclause 6.3.13 and 6.3.14 in IEEE Std 802.16-2004" ::= { wmanIf2BsPacketCs 1 } wmanIf2BsProvisionedSfEntry OBJECT-TYPE SYNTAX WmanIf2BsProvisionedSfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each service flow provisioned by NMS. The table is indexed by ifIndex and wmanIf2BsSfId. ifIndex is associated with the BS sector." INDEX { ifIndex, wmanIf2BsSfId } ::= { wmanIf2BsProvisionedSfTable 1 } WmanIf2BsProvisionedSfEntry ::= SEQUENCE { wmanIf2BsSfId Unsigned32, wmanIf2BsSfDirection INTEGER, wmanIf2BsServiceClassIndex INTEGER, wmanIf2BsSfState WmanIf2SfState, wmanIf2BsSfProvisionedTime TimeStamp, wmanIf2BsSfCsSpecification WmanIf2CsSpecification, wmanIf2BsProvisionedSfRowStatus RowStatus} wmanIf2BsSfId OBJECT-TYPE SYNTAX Unsigned32 (1 .. 4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A 32 bit quantity that uniquely identifies a service flow to both the subscriber station and base station (BS)." ::= { wmanIf2BsProvisionedSfEntry 1 } wmanIf2BsSfDirection OBJECT-TYPE SYNTAX INTEGER {downstream(1), upstream(2)} MAX-ACCESS read-create STATUS current DESCRIPTION "An attribute indicating the service flow is downstream or upstream." ::= { wmanIf2BsProvisionedSfEntry 2 } wmanIf2BsServiceClassIndex OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "The index in wmanIf2BsServiceClassTable describing the service class or QoS parameters for such service flow. If no associated entry in wmanIf2BsServiceClassTable exists, this object returns a value of zero." ::= { wmanIf2BsProvisionedSfEntry 3 } wmanIf2BsSfState OBJECT-TYPE SYNTAX WmanIf2SfState MAX-ACCESS read-create STATUS current DESCRIPTION "wmanIf2BsSfState determines the requested state of a service flow. - authorized state: A service flow is provisioned but not resource is reserved yet - admitted state: service flow has resources reserved. - active state: has resources committed by the BS (e.g., is actively sending maps containing unsolicited grants for a UGS-based service flow)," REFERENCE "Subclause 6.3.14.6, in IEEE Std 802.16-2004" ::= { wmanIf2BsProvisionedSfEntry 4 } wmanIf2BsSfProvisionedTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the date and time when the service flow is provisioned." ::= { wmanIf2BsProvisionedSfEntry 5 } wmanIf2BsSfCsSpecification OBJECT-TYPE SYNTAX WmanIf2CsSpecification MAX-ACCESS read-create STATUS current DESCRIPTION "This parameter specifies the convergence sublayer encapsulation mode." REFERENCE "Subclause 11.13.19.1 in IEEE Std 802.16-2004" ::= { wmanIf2BsProvisionedSfEntry 6 } wmanIf2BsProvisionedSfRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table. If the implementator of this MIB has choosen not to implement 'dynamic assignment' of profiles, this object is not useful and should return noSuchName upon SNMP request." ::= { wmanIf2BsProvisionedSfEntry 7 } wmanIf2BsSsProvisionedForSfTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2BsSsProvisionedForSfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table maps the MAC addresses of SSs to the service flows provisioned in wmanIf2BsProvisionedSfTable." REFERENCE "Subclause 6.3.14 in IEEE Std 802.16-2004" ::= { wmanIf2BsPacketCs 2 } wmanIf2BsSsProvisionedForSfEntry OBJECT-TYPE SYNTAX WmanIf2BsSsProvisionedForSfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is indexed by wmanIf2BsSsProvMacAddress and wmanIf2BsProvSfId." INDEX { wmanIf2BsSsProvMacAddress, wmanIf2BsProvSfId } ::= { wmanIf2BsSsProvisionedForSfTable 1 } WmanIf2BsSsProvisionedForSfEntry ::= SEQUENCE { wmanIf2BsSsProvMacAddress MacAddress, wmanIf2BsProvSfId Unsigned32, wmanIf2BsSsProvisionedForSfRowStatus RowStatus} wmanIf2BsSsProvMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The MAC address of the SS, the service flow is created with." ::= { wmanIf2BsSsProvisionedForSfEntry 1 } wmanIf2BsProvSfId OBJECT-TYPE SYNTAX Unsigned32 (1 .. 4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A 32 bit quantity that uniquely identifies a service flow. The value of this object can be used by BS to index the wman2BsProvisionedSfTable." ::= { wmanIf2BsSsProvisionedForSfEntry 2 } wmanIf2BsSsProvisionedForSfRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to ensure that the write, create, delete operation to multiple columns is guaranteed to be treated as atomic operation by agent." ::= { wmanIf2BsSsProvisionedForSfEntry 3 } wmanIf2BsServiceClassTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2BsServiceClassEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is provisioned and is indexed by wmanIf2BsQoSProfileIndex. Each entry of the table contains corresponding service flow characteristic attributes (e.g. QoS parameter set). The value of wmanIf2BsQoSProfileIndex is obtained from wmanIf2BsServiceClassIndex in wmanIf2BsProvisionedSfTable" REFERENCE "Subclause 6.3.14.4 in IEEE Std 802.16-2004" ::= { wmanIf2BsPacketCs 3 } wmanIf2BsServiceClassEntry OBJECT-TYPE SYNTAX WmanIf2BsServiceClassEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each service class" INDEX { ifIndex, wmanIf2BsQoSProfileIndex } ::= { wmanIf2BsServiceClassTable 1 } WmanIf2BsServiceClassEntry ::= SEQUENCE { wmanIf2BsQoSProfileIndex INTEGER, wmanIf2BsQosServiceClassName WmanIf2ServClassName, wmanIf2BsQoSTrafficPriority INTEGER, wmanIf2BsQoSMaxSustainedRate Unsigned32, wmanIf2BsQoSMaxTrafficBurst Unsigned32, wmanIf2BsQoSMinReservedRate Unsigned32, wmanIf2BsQoSToleratedJitter Unsigned32, wmanIf2BsQoSMaxLatency Unsigned32, wmanIf2BsQoSFixedVsVariableSduInd INTEGER, wmanIf2BsQoSSduSize Unsigned32, wmanIf2BsQosScSchedulingType WmanIf2SfSchedulingType, wmanIf2BsQosScArqEnable TruthValue, wmanIf2BsQosScArqWindowSize INTEGER, wmanIf2BsQosScArqBlockLifetime INTEGER, wmanIf2BsQosScArqSyncLossTimeout INTEGER, wmanIf2BsQosScArqDeliverInOrder TruthValue, wmanIf2BsQosScArqRxPurgeTimeout INTEGER, wmanIf2BsQosScArqBlockSize INTEGER, wmanIf2BsQosSCMinRsvdTolerableRate Unsigned32, wmanIf2BsQoSReqTxPolicy BITS, wmanIf2BsQoSServiceClassRowStatus RowStatus} wmanIf2BsQoSProfileIndex OBJECT-TYPE SYNTAX INTEGER (1 .. 65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index value which uniquely identifies an entry in the wmanIf2BsServiceClassTable" ::= { wmanIf2BsServiceClassEntry 1 } wmanIf2BsQosServiceClassName OBJECT-TYPE SYNTAX WmanIf2ServClassName MAX-ACCESS read-create STATUS current DESCRIPTION "Refers to the Service Class Name" REFERENCE "Subclause 11.13.3 in IEEE Std 802.16-2004" ::= { wmanIf2BsServiceClassEntry 2 } wmanIf2BsQoSTrafficPriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this parameter specifies the priority assigned to a service flow. For uplink service flows, the BS should use this parameter when determining precedence in request service and grant generation, and the SS shall preferentially select contention Request opportunities for Priority Request CIDs based on this priority. Higher numbers indicate higher priority" REFERENCE "Subclause 11.13.5 in IEEE Std 802.16-2004" ::= { wmanIf2BsServiceClassEntry 3 } wmanIf2BsQoSMaxSustainedRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "b/s" MAX-ACCESS read-create STATUS current DESCRIPTION "This parameter defines the peak information rate of the service. The rate is expressed in bits per second and pertains to the SDUs at the input to the system." REFERENCE "Subclause 11.13.6 in IEEE Std 802.16-2004" ::= { wmanIf2BsServiceClassEntry 4 } wmanIf2BsQoSMaxTrafficBurst OBJECT-TYPE SYNTAX Unsigned32 UNITS "byte" MAX-ACCESS read-create STATUS current DESCRIPTION "This parameter defines the maximum burst size that must be accommodated for the service." REFERENCE "Subclause 11.13.7 in IEEE Std 802.16-2004" ::= { wmanIf2BsServiceClassEntry 5 } wmanIf2BsQoSMinReservedRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "b/s" MAX-ACCESS read-create STATUS current DESCRIPTION "This parameter specifies the minimum rate reserved for this service flow." REFERENCE "Subclause 11.13.8 in IEEE Std 802.16-2004" ::= { wmanIf2BsServiceClassEntry 6 } wmanIf2BsQoSToleratedJitter OBJECT-TYPE SYNTAX Unsigned32 UNITS "millisecond" MAX-ACCESS read-create STATUS current DESCRIPTION "This parameter defines the Maximum delay variation (jitter) for the connection." REFERENCE "Subclause 11.13.13 in IEEE Std 802.16-2004" ::= { wmanIf2BsServiceClassEntry 7 } wmanIf2BsQoSMaxLatency OBJECT-TYPE SYNTAX Unsigned32 UNITS "millisecond" MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this parameter specifies the maximum latency between the reception of a packet by the BS or SS on its network interface and the forwarding of the packet to its RF Interface." REFERENCE "Subclause 11.13.14 in IEEE Std 802.16-2004" ::= { wmanIf2BsServiceClassEntry 8 } wmanIf2BsQoSFixedVsVariableSduInd OBJECT-TYPE SYNTAX INTEGER {variableLength(0), fixedLength(1)} MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this parameter specifies whether the SDUs on the service flow are variable-length (0) or fixed-length (1). The parameter is used only if packing is on for the service flow. The default value is 0, i.e.,variable-length SDUs." REFERENCE "Subclause 11.13.15 in IEEE Std 802.16-2004" DEFVAL { variableLength } ::= { wmanIf2BsServiceClassEntry 9 } wmanIf2BsQoSSduSize OBJECT-TYPE SYNTAX Unsigned32 UNITS "byte" MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this parameter specifies the length of the SDU for a fixed-length SDU service flow. This parameter is used only if packing is on and the service flow is indicated as carrying fixed-length SDUs. The default value is 49 bytes, i.e., VC-switched ATM cells with PHS. The parameter is relevant for both ATM and Packet Convergence Sublayers." REFERENCE "Subclause 11.13.16 in IEEE Std 802.16-2004" DEFVAL { 49 } ::= { wmanIf2BsServiceClassEntry 10 } wmanIf2BsQosScSchedulingType OBJECT-TYPE SYNTAX WmanIf2SfSchedulingType MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the upstream scheduling service used for upstream service flow. If the referenced parameter is not present in the corresponding 802.16 QOS Parameter Set of an upstream service flow, the default value of this object is bestEffort(2)." REFERENCE "Subclause 11.13.11 in IEEE Std 802.16-2004" DEFVAL {bestEffort} ::= { wmanIf2BsServiceClassEntry 11 } wmanIf2BsQosScArqEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "True(1) ARQ enabling is requested for the connection." REFERENCE "Subclause 11.13.18 in IEEE Std 802.16-2004" ::= { wmanIf2BsServiceClassEntry 12 } wmanIf2BsQosScArqWindowSize OBJECT-TYPE SYNTAX INTEGER (1 .. 1024) MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the maximum number of unacknowledged fragments at any time." REFERENCE "Subclause 11.13.18 in IEEE Std 802.16-2004" ::= { wmanIf2BsServiceClassEntry 13 } wmanIf2BsQosScArqBlockLifetime OBJECT-TYPE SYNTAX INTEGER (0 .. 65535) UNITS "10 us" MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum time interval an ARQ fragment will be managed by the transmitter ARQ machine, once initial transmission of the fragment has occured. If transmission or retransmission of the fragment is not acknowledged by the receiver before the time limit is reached, the fragment is discarded. A value of 0 means Infinite." REFERENCE "Subclause 11.13.18 in IEEE Std 802.16-2004" DEFVAL {0} ::= { wmanIf2BsServiceClassEntry 14 } wmanIf2BsQosScArqSyncLossTimeout OBJECT-TYPE SYNTAX INTEGER (0 .. 65535 ) UNITS "10 us" MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum interval before declaring a loss of synchronization of the sender and receiver state machines. A value of 0 means Infinite." REFERENCE "Subclause 11.13.18 in IEEE Std 802.16-2004" DEFVAL {0} ::= { wmanIf2BsServiceClassEntry 15 } wmanIf2BsQosScArqDeliverInOrder OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether or not data is to be delivered by the receiving MAC to its client application in the order in which data was handed off to the originating MAC." REFERENCE "Subclause 11.13.18 in IEEE Std 802.16-2004" ::= { wmanIf2BsServiceClassEntry 16 } wmanIf2BsQosScArqRxPurgeTimeout OBJECT-TYPE SYNTAX INTEGER (0 .. 65535) UNITS "10 us" MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the time interval the ARQ window is advanced after a fragment is received. A value of 0 means Infinite." REFERENCE "Subclause 11.13.18 in IEEE Std 802.16-2004" DEFVAL {0} ::= { wmanIf2BsServiceClassEntry 17 } wmanIf2BsQosScArqBlockSize OBJECT-TYPE SYNTAX INTEGER (1..2040) UNITS "byte" MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this parameter specifies the size of an ARQ block. This parameter shall be established by negotiation during the connection creation dialog." REFERENCE "Subclause 11.13.18.8 in IEEE Std 802.16-2004" ::= { wmanIf2BsServiceClassEntry 18 } wmanIf2BsQosSCMinRsvdTolerableRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "b/s" MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum Tolerable Traffic Rate = R (bits/sec) with time base T(sec) means the following. Let S denote additional demand accumulated at the MAC SAP of the transmitter during an arbitrary time interval of the length T. Then the amount of data forwarded at the receiver to CS (in bits) during this interval should be not less than min {S, R * T}." REFERENCE "Subclause 11.13.9 in IEEE Std 802.16-2004" ::= { wmanIf2BsServiceClassEntry 19 } wmanIf2BsQoSReqTxPolicy OBJECT-TYPE SYNTAX BITS {noBroadcastBwReq(0), reserved1(1), noPiggybackReq(2), noFragmentData(3), noPHS(4), noSduPacking(5), noCrc(6), reserved2(7)} MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this parameter provides the capability to specify certain attributes for the associated service flow. An attribute is enabled by setting the corresponding bit position to 1." REFERENCE "Subclause 11.13.12 in IEEE Std 802.16-2004" ::= { wmanIf2BsServiceClassEntry 20 } wmanIf2BsQoSServiceClassRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table. If the implementator of this MIB has choosen not to implement 'dynamic assignment' of profiles, this object is not useful and should return noSuchName upon SNMP request." ::= { wmanIf2BsServiceClassEntry 21 } wmanIf2BsClassifierRuleTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2BsClassifierRuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains packet classifier rules associated with service flows." REFERENCE "Subclause 11.13.19.3.4 in IEEE Std 802.16-2004" ::= { wmanIf2BsPacketCs 4 } wmanIf2BsClassifierRuleEntry OBJECT-TYPE SYNTAX WmanIf2BsClassifierRuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each packet classifier rule, and is indexed by ifIndex, wmanIf2BsSfId, and wmanIf2BsClassifierRuleIndex. IfIdex is associated with the BS sector. wmanIf2BsSfId identifies the service flow, while wmanIf2BsClassifierRuleIndex identifies the packet classifier rule." INDEX { ifIndex, wmanIf2BsSfId, wmanIf2BsClassifierRuleIndex } ::= { wmanIf2BsClassifierRuleTable 1 } WmanIf2BsClassifierRuleEntry::= SEQUENCE { wmanIf2BsClassifierRuleIndex Unsigned32, wmanIf2BsClassifierRulePriority INTEGER, wmanIf2BsClassifierRuleIpTosLow INTEGER, wmanIf2BsClassifierRuleIpTosHigh INTEGER, wmanIf2BsClassifierRuleIpTosMask INTEGER, wmanIf2BsClassifierRuleIpProtocol Integer32, wmanIf2BsClassifierRuleIpSourceAddr InetAddress, wmanIf2BsClassifierRuleIpSourceMask InetAddress, wmanIf2BsClassifierRuleIpDestAddr InetAddress, wmanIf2BsClassifierRuleIpDestMask InetAddress, wmanIf2BsClassifierRuleSourcePortStart Integer32, wmanIf2BsClassifierRuleSourcePortEnd Integer32, wmanIf2BsClassifierRuleDestPortStart Integer32, wmanIf2BsClassifierRuleDestPortEnd Integer32, wmanIf2BsClassifierRuleDestMacAddr MacAddress, wmanIf2BsClassifierRuleDestMacMask MacAddress, wmanIf2BsClassifierRuleSourceMacAddr MacAddress, wmanIf2BsClassifierRuleSourceMacMask MacAddress, wmanIf2BsClassifierRuleEnetProtocolType INTEGER, wmanIf2BsClassifierRuleEnetProtocol Integer32, wmanIf2BsClassifierRuleUserPriLow Integer32, wmanIf2BsClassifierRuleUserPriHigh Integer32, wmanIf2BsClassifierRuleVlanId Integer32, wmanIf2BsClassifierRuleState INTEGER, wmanIf2BsClassifierRulePhsSize Integer32, wmanIf2BsClassifierRulePhsMask OCTET STRING, wmanIf2BsClassifierRulePhsVerify WmanIf2PhsRuleVerify, wmanIf2BsClassifierRuleIpv6FlowLabel WmanIf2Ipv6FlowLabel, wmanIf2BsClassifierRuleBitMap WmanIf2ClassifierBitMap, wmanIf2BsClassifierRuleRowStatus RowStatus} wmanIf2BsClassifierRuleIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index is assigned to a classifier in BS classifiers table" ::= { wmanIf2BsClassifierRuleEntry 1 } wmanIf2BsClassifierRulePriority OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "The value specifies the priority for the Classifier, which is used for determining the order of the Classifier. A higher value indicates higher priority. Classifiers may have priorities in the range 0..255." REFERENCE "Subclause 11.13.19.3.4.1 in IEEE Std 802.16-2004" DEFVAL { 0 } ::= { wmanIf2BsClassifierRuleEntry 2 } wmanIf2BsClassifierRuleIpTosLow OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "The low value of a range of TOS byte values. If the referenced parameter is not present in a classifier, this object reports the value of 0." REFERENCE "Subclause 11.13.19.3.4.2 in IEEE Std 802.16-2004" ::= { wmanIf2BsClassifierRuleEntry 3 } wmanIf2BsClassifierRuleIpTosHigh OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "The 8-bit high value of a range of TOS byte values. If the referenced parameter is not present in a classifier, this object reports the value of 0." REFERENCE "Subclause 11.13.19.3.4.2 in IEEE Std 802.16-2004" ::= { wmanIf2BsClassifierRuleEntry 4 } wmanIf2BsClassifierRuleIpTosMask OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this object specifies the matching parameter for the IP type of service/DSCP [IETF RFC 2474] byte mask. An IP packet with IP type of service (ToS) byte value ip-tos matches this parameter if tos-low less than or equal (ip-tos AND tos-mask) less than or equal tos-high." REFERENCE "Subclause 11.13.19.3.4.2 in IEEE Std 802.16-2004" ::= { wmanIf2BsClassifierRuleEntry 5 } wmanIf2BsClassifierRuleIpProtocol OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the value of the IP Protocol field required for IP packets to match this rule. If the referenced parameter is not present in a classifier, this object reports the value of 0." REFERENCE "Subclause 11.13.19.3.4.3 in IEEE Std 802.16-2004" ::= { wmanIf2BsClassifierRuleEntry 6 } wmanIf2BsClassifierRuleIpSourceAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the value of the IP Source Address required for packets to match this rule. An IP packet matches the rule when the packet ip source address bitwise ANDed with the wmanIf2BsClassifierRuleIpSourceMask value equals the wmanIf2BsClassifierRuleIpSourceAddr value. If the referenced parameter is not present in a classifier, this object reports the value of 0.0.0.0." REFERENCE "Subclause 11.13.19.3.4.4 in IEEE Std 802.16-2004" ::= { wmanIf2BsClassifierRuleEntry 7 } wmanIf2BsClassifierRuleIpSourceMask OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies which bits of a packet's IP Source Address that are compared to match this rule. An IP packet matches the rule when the packet source address bitwise ANDed with the wmanIf2BsClassifierRuleIpSourceMask value equals the wmanIf2BsClassifierRuleIpSourceAddr value. If the referenced parameter is not present in a classifier, this object reports the value of 0.0.0.0." REFERENCE "Subclause 11.13.19.3.4.4 in IEEE Std 802.16-2004" ::= { wmanIf2BsClassifierRuleEntry 8 } wmanIf2BsClassifierRuleIpDestAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the value of the IP Destination Address required for packets to match this rule. An IP packet matches the rule when the packet IP destination address bitwise ANDed with the wmanIf2BsClassifierRuleIpDestMask value equals the wmanIf2BsClassifierRuleIpDestAddr value. If the referenced parameter is not present in a classifier, this object reports the value of 0.0.0.0." REFERENCE "Subclause 11.13.19.3.4.5 in IEEE Std 802.16-2004" ::= { wmanIf2BsClassifierRuleEntry 9 } wmanIf2BsClassifierRuleIpDestMask OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies which bits of a packet's IP Destination Address that are compared to match this rule. An IP packet matches the rule when the packet destination address bitwise ANDed with the wmanIf2BsClassifierRuleIpDestMask value equals the wmanIf2BsClassifierRuleIpDestAddr value. If the referenced parameter is not present in a classifier , this object reports the value of 0.0.0.0." REFERENCE "Subclause 11.13.19.3.4.5 in IEEE Std 802.16-2004" ::= { wmanIf2BsClassifierRuleEntry 10 } wmanIf2BsClassifierRuleSourcePortStart OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the low end inclusive range of TCP/UDP source port numbers to which a packet is compared. This object is irrelevant for non-TCP/UDP IP packets. If the referenced parameter is not present in a classifier, this object reports the value of 0." REFERENCE "Subclause 11.13.19.3.4.6 in IEEE Std 802.16-2004" ::= { wmanIf2BsClassifierRuleEntry 11 } wmanIf2BsClassifierRuleSourcePortEnd OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the high end inclusive range of TCP/UDP source port numbers to which a packet is compared. This object is irrelevant for non-TCP/UDP IP packets. If the referenced parameter is not present in a classifier, this object reports the value of 65535." REFERENCE "Subclause 11.13.19.3.4.6 in IEEE Std 802.16-2004" ::= { wmanIf2BsClassifierRuleEntry 12 } wmanIf2BsClassifierRuleDestPortStart OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the low end inclusive range of TCP/UDP destination port numbers to which a packet is compared. If the referenced parameter is not present in a classifier, this object reports the value of 0." REFERENCE "Subclause 11.13.19.3.4.7 in IEEE Std 802.16-2004" ::= { wmanIf2BsClassifierRuleEntry 13 } wmanIf2BsClassifierRuleDestPortEnd OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the high end inclusive range of TCP/UDP destination port numbers to which a packet is compared. If the referenced parameter is not present in a classifier, this object reports the value of 65535." REFERENCE "Subclause 11.13.19.3.4.7 in IEEE Std 802.16-2004" ::= { wmanIf2BsClassifierRuleEntry 14 } wmanIf2BsClassifierRuleDestMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-create STATUS current DESCRIPTION "An Ethernet packet matches an entry when its destination MAC address bitwise ANDed with wmanIf2BsClassifierRuleDestMacMask equals the value of wmanIf2BsClassifierRuleDestMacAddr. If the referenced parameter is not present in a classifier, this object reports the value of '000000000000'H." REFERENCE "Subclause 11.13.19.3.4.8 in IEEE Std 802.16-2004" ::= { wmanIf2BsClassifierRuleEntry 15 } wmanIf2BsClassifierRuleDestMacMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-create STATUS current DESCRIPTION "An Ethernet packet matches an entry when its destination MAC address bitwise ANDed with wmanIf2BsClassifierRuleDestMacMask equals the value of wmanIf2BsClassifierRuleDestMacAddr. If the referenced parameter is not present in a classifier, this object reports the value of '000000000000'H." REFERENCE "Subclause 11.13.19.3.4.8 in IEEE Std 802.16-2004" ::= { wmanIf2BsClassifierRuleEntry 16 } wmanIf2BsClassifierRuleSourceMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-create STATUS current DESCRIPTION "An Ethernet packet matches this entry when its source MAC address bitwise ANDed with wmanIf2BsClassifierRuleSourceMacMask equals the value of wmanIf2BsClassifierRuleSourceMacAddr. If the referenced parameter is not present in a classifier, this object reports the value of '000000000000'H." REFERENCE "Subclause 11.13.19.3.4.9 in IEEE Std 802.16-2004" ::= { wmanIf2BsClassifierRuleEntry 17 } wmanIf2BsClassifierRuleSourceMacMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-create STATUS current DESCRIPTION "An Ethernet packet matches an entry when its source MAC address bitwise ANDed with wmanIf2BsClassifierRuleSourceMacMask equals the value of wmanIf2BsClassifierRuleSourceMacAddr. If the referenced parameter is not present in a classifier, this object reports the value of '000000000000'H." REFERENCE "Subclause 11.13.19.3.4.9 in IEEE Std 802.16-2004" ::= { wmanIf2BsClassifierRuleEntry 18 } wmanIf2BsClassifierRuleEnetProtocolType OBJECT-TYPE SYNTAX INTEGER {none(0), ethertype(1), dsap(2)} MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the format of the layer 3 protocol id in the Ethernet packet. A value of none(0) means that the rule does not use the layer 3 protocol type as a matching criteria. A value of ethertype(1) means that the rule applies only to frames which contains an EtherType value. Ethertype values are contained in packets using the Dec-Intel-Xerox (DIX) encapsulation or the RFC1042 Sub-Network Access Protocol (SNAP) encapsulation formats. A value of dsap(2) means that the rule applies only to frames using the IEEE802.3 encapsulation format with a Destination Service Access Point (DSAP) other than 0xAA (which is reserved for SNAP). If the Ethernet frame contains an 802.1P/Q Tag header (i.e. EtherType 0x8100), this object applies to the embedded EtherType field within the 802.1P/Q header. If the referenced parameter is not present in a classifier, this object reports the value of 0." REFERENCE "Subclause 11.13.19.3.4.10 in IEEE Std 802.16-2004" ::= { wmanIf2BsClassifierRuleEntry 19 } wmanIf2BsClassifierRuleEnetProtocol OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "If wmanIf2BsClassifierRuleEnetProtocolType is none(0), this object is ignored when considering whether a packet matches the current rule. If wmanIf2BsClassifierRuleEnetProtocolType is ethertype(1), this object gives the 16-bit value of the EtherType that the packet must match in order to match the rule. If wmanIf2BsClassifierRuleEnetProtocolType is dsap(2), the lower 8 bits of this object's value must match the DSAP byte of the packet in order to match the rule. If the Ethernet frame contains an 802.1P/Q Tag header (i.e. EtherType 0x8100), this object applies to the embedded EtherType field within the 802.1P/Q header. If the referenced parameter is not present in the classifier, the value of this object is reported as 0." REFERENCE "Subclause 11.13.19.3.4.10 in IEEE Std 802.16-2004" ::= { wmanIf2BsClassifierRuleEntry 20 } wmanIf2BsClassifierRuleUserPriLow OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-create STATUS current DESCRIPTION "This object applies only to Ethernet frames using the 802.1P/Q tag header (indicated with EtherType 0x8100). Such frames include a 16-bit Tag that contains a 3 bit Priority field and a 12 bit VLAN number. Tagged Ethernet packets must have a 3-bit Priority field within the range of wmanIf2BsClassifierRuleUserPriLow and wmanIf2BsClassifierRuleUserPriHigh in order to match this rule. If the referenced parameter is not present in the classifier, the value of this object is reported as 0." REFERENCE "Subclause 11.13.19.3.4.11 in IEEE Std 802.16-2004" ::= { wmanIf2BsClassifierRuleEntry 21 } wmanIf2BsClassifierRuleUserPriHigh OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-create STATUS current DESCRIPTION "This object applies only to Ethernet frames using the 802.1P/Q tag header (indicated with EtherType 0x8100). Such frames include a 16-bit Tag that contains a 3 bit Priority field and a 12 bit VLAN number. Tagged Ethernet packets must have a 3-bit Priority field within the range of wmanIf2BsClassifierRuleUserPriLow and wmanIf2BsClassifierRuleUserPriHigh in order to match this rule. If the referenced parameter is not present in the classifier, the value of this object is reported as 7." REFERENCE "Subclause 11.13.19.3.4.11 in IEEE Std 802.16-2004" ::= { wmanIf2BsClassifierRuleEntry 22 } wmanIf2BsClassifierRuleVlanId OBJECT-TYPE SYNTAX Integer32 (0..4095) MAX-ACCESS read-create STATUS current DESCRIPTION "This object applies only to Ethernet frames using the 802.1P/Q tag header. If this object's value is nonzero, tagged packets must have a VLAN Identifier that matches the value in order to match the rule. Only the least significant 12 bits of this object's value are valid. If the referenced parameter is not present in the classifier, the value of this object is reported as 0." REFERENCE "Subclause 11.13.19.3.4.12 in IEEE Std 802.16-2004" ::= { wmanIf2BsClassifierRuleEntry 23 } wmanIf2BsClassifierRuleState OBJECT-TYPE SYNTAX INTEGER {active(1), inactive(2)} MAX-ACCESS read-create STATUS deprecated DESCRIPTION "This object indicates whether or not the classifier is enabled to classify packets to a Service Flow. If the referenced parameter is not present in the classifier, the value of this object is reported as active(1)." ::= { wmanIf2BsClassifierRuleEntry 24 } wmanIf2BsClassifierRulePhsSize OBJECT-TYPE SYNTAX Integer32 (0..255) UNITS "byte" MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to configure the PHS rule for this classifer. The value of this field - PHSS is the total number of bytes in the header to be suppressed and then restored in a service flow that uses PHS. If the value of this field is 0 bytes then PHS is disabled for this classifer. If flag phsMask in wmanIf2BsClassifierRuleBitMap is set to 0 and flag phsSize in wmanIf2BsClassifierRuleBitMap is set to 0, then BS can still create PHS rules using its own custom mask (i.e. the rule is not configured by NMS)." REFERENCE "Subclause 11.13.19.3.7.4 in IEEE Std 802.16-2004" DEFVAL {0} ::= { wmanIf2BsClassifierRuleEntry 25 } wmanIf2BsClassifierRulePhsMask OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..65535)) MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to configure the PHS rule for this classifer. It is encoded as follows: bit 0: 0 = don't suppress the 1st byte of the suppression field 1 = suppress first byte of the suppression field bit 1: 0 = don't suppress the 2nd byte of the suppression field 1 = suppress second byte of the suppression field bit x: 0 = don't suppress the (x+1) byte of the suppression field 1 = suppress (x+1) byte of the suppression field where the length of the octet string is ceiling (wmanIf2BsClassifierRulePhsSize/8). BS should use this value to create a new PHS rule index (PHSI) and field (PHSF) as defined in the standard. If flag phsMask in wmanIf2BsClassifierRuleBitMap is set to 0 and flag phsSize in wmanIf2BsClassifierRuleBitMap is set to 0, then BS can still create PHS rules using its own custom mask (i.e. the rule is not configured by NMS)." REFERENCE "Subclause 11.13.19.3.7.3 in IEEE Std 802.16-2004" ::= { wmanIf2BsClassifierRuleEntry 26 } wmanIf2BsClassifierRulePhsVerify OBJECT-TYPE SYNTAX WmanIf2PhsRuleVerify MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this field indicates to the sending entity whether or not the packet header contents are to be verified prior to performing suppression." DEFVAL { phsVerifyEnable } ::= { wmanIf2BsClassifierRuleEntry 27 } wmanIf2BsClassifierRuleIpv6FlowLabel OBJECT-TYPE SYNTAX WmanIf2Ipv6FlowLabel MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this field specifies the matching values for the IPv6 Flow label field." ::= { wmanIf2BsClassifierRuleEntry 28 } wmanIf2BsClassifierRuleBitMap OBJECT-TYPE SYNTAX WmanIf2ClassifierBitMap MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates which parameter encodings were actually present in the entry. A bit set to '1' indicates the corresponding classifier encoding is present, and '0' means otherwise" ::= { wmanIf2BsClassifierRuleEntry 29 } wmanIf2BsClassifierRuleRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table. If the implementator of this MIB has choosen not to implement 'dynamic assignment' of profiles, this object is not useful and should return noSuchName upon SNMP request." ::= { wmanIf2BsClassifierRuleEntry 30 } wmanIf2BsSsPacketCounterTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2BsSsPacketCounterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains counters to keep track of the number of packets and octets that have been received or transmitted on the per service flow basis." ::= { wmanIf2BsPacketCs 5 } wmanIf2BsSsPacketCounterEntry OBJECT-TYPE SYNTAX WmanIf2BsSsPacketCounterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each service flow, and is indexed by ifIndex, wmanIf2CmnCpsSfMacAddress, and wmanIf2CmnCpsSfId." INDEX { ifIndex, wmanIf2CmnCpsSfMacAddress, wmanIf2CmnCpsSfId } ::= { wmanIf2BsSsPacketCounterTable 1 } WmanIf2BsSsPacketCounterEntry::= SEQUENCE { wmanIf2BsSsMacSduCount Counter64, wmanIf2BsSsOctetCount Counter64, wmanIf2BsSsResetCounter INTEGER, wmanIf2BsSsResetCounterTime TimeStamp} wmanIf2BsSsMacSduCount OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This object counts the number of MAC SDUs that have been transmitted or received." ::= { wmanIf2BsSsPacketCounterEntry 1 } wmanIf2BsSsOctetCount OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This object counts the number of octets of MAC SDUs that have been transmitted or received." ::= { wmanIf2BsSsPacketCounterEntry 2 } wmanIf2BsSsResetCounter OBJECT-TYPE SYNTAX INTEGER {null(0), resetCounter(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "When this attribute is SET to resetCounter(1), the corresponding entry of packet counters will be reset. A GET operation performed on this object will always return null(0). The counter is normally reset after the packet count information is retrieved. " ::= { wmanIf2BsSsPacketCounterEntry 3 } wmanIf2BsSsResetCounterTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the date and time when the counter is reset." ::= { wmanIf2BsSsPacketCounterEntry 4 } -- -- wmanIf2BsCps contain the Base Station Common Part Sublayer objects -- wmanIf2BsCps OBJECT IDENTIFIER ::= { wmanIf2BsObjects 2 } wmanIf2BsRegisteredSsTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2BsRegisteredSsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the basic capability information of SSs that have been negotiated and agreed between BS and SS via REG-REQ and REG-RSP messages. An entry in this table indicates the SS has entered and registered into the BS." REFERENCE "Subclause 6.3.2.3.7 in IEEE Std 802.16-2004" ::= { wmanIf2BsCps 1 } wmanIf2BsRegisteredSsEntry OBJECT-TYPE SYNTAX WmanIf2BsRegisteredSsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each SS that has been registered in the BS, and is indexed by wmanIf2BsSsMacAddress. The primary index is the ifIndex with an ifType of propBWAp2Mp, indicating the BS sector with which the SS is associated. wmanIf2BsSsMacAddress identifies the SS being registered." INDEX { ifIndex, wmanIf2BsSsMacAddress } ::= { wmanIf2BsRegisteredSsTable 1 } WmanIf2BsRegisteredSsEntry ::= SEQUENCE { wmanIf2BsSsMacAddress MacAddress, wmanIf2BsSsBasicCid WmanIf2CidType, wmanIf2BsSsPrimaryCid WmanIf2CidType, wmanIf2BsSsSecondaryCid WmanIf2CidType, wmanIf2BsSsManagementSupport INTEGER, wmanIf2BsSsIpManagementMode INTEGER, wmanIf2BsSs2ndMgmtArqEnable TruthValue, wmanIf2BsSs2ndMgmtArqWindowSize INTEGER, wmanIf2BsSs2ndMgmtArqDnLinkTxDelay INTEGER, wmanIf2BsSs2ndMgmtArqUpLinkTxDelay INTEGER, wmanIf2BsSs2ndMgmtArqDnLinkRxDelay INTEGER, wmanIf2BsSs2ndMgmtArqUpLinkRxDelay INTEGER, wmanIf2BsSs2ndMgmtArqBlockLifetime INTEGER, wmanIf2BsSs2ndMgmtArqSyncLossTimeout INTEGER, wmanIf2BsSs2ndMgmtArqDeliverInOrder TruthValue, wmanIf2BsSs2ndMgmtArqRxPurgeTimeout INTEGER, wmanIf2BsSs2ndMgmtArqBlockSize INTEGER, wmanIf2BsSsVendorIdEncoding OCTET STRING, wmanIf2BsSsAasBroadcastPermission INTEGER, wmanIf2BsSsMaxTxPowerBpsk WmanIf2MaxTxPowerType, wmanIf2BsSsMaxTxPowerQpsk WmanIf2MaxTxPowerType, wmanIf2BsSsMaxTxPower16Qam WmanIf2MaxTxPowerType, wmanIf2BsSsMaxTxPower64Qam WmanIf2MaxTxPowerType, wmanIf2BsSsMacVersion WmanIf2MacVersion} wmanIf2BsSsMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The MAC address of SS is received from the RNG-REQ message. When SS registers, this MAC address is entered into the table, and used as the identifier to the SS." REFERENCE "Subclause 6.3.2.3.5 in IEEE Std 802.16-2004" ::= { wmanIf2BsRegisteredSsEntry 1 } wmanIf2BsSsBasicCid OBJECT-TYPE SYNTAX WmanIf2CidType MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object indicates the SS's basic CID that was sent in the RNG-RSP message." REFERENCE "Subclause 6.3.2.3.6 in IEEE Std 802.16-2004" ::= { wmanIf2BsRegisteredSsEntry 2 } wmanIf2BsSsPrimaryCid OBJECT-TYPE SYNTAX WmanIf2CidType MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object indicates the primary CID of the SS received from the RNG-RSP message." REFERENCE "Subclause 6.3.2.3.6 in IEEE Std 802.16-2004" ::= { wmanIf2BsRegisteredSsEntry 3 } wmanIf2BsSsSecondaryCid OBJECT-TYPE SYNTAX WmanIf2CidType MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object indicates the secondary management CID present in the REG-RSP message. The value should be null if the 2nd management connection is not available." REFERENCE "Subclause 6.4.2.3.8 in IEEE Std 802.16-2004" ::= { wmanIf2BsRegisteredSsEntry 4 } wmanIf2BsSsManagementSupport OBJECT-TYPE SYNTAX INTEGER {unmanagedSs(0), managedSs(1)} MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether or not the SS is managed." REFERENCE "Subclause 11.7.2 in IEEE Std 802.16-2004" ::= { wmanIf2BsRegisteredSsEntry 5 } wmanIf2BsSsIpManagementMode OBJECT-TYPE SYNTAX INTEGER {unmanaged(0), ipManaged(1)} MAX-ACCESS read-only STATUS current DESCRIPTION "The IP management mode parameter dictates whether the provider intends to manage the SS on an ongoing basis via IP-based mechanisms." REFERENCE "Subclause 11.7.3 in IEEE Std 802.16-2004" ::= { wmanIf2BsRegisteredSsEntry 6 } wmanIf2BsSs2ndMgmtArqEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "True(1) ARQ enabling is requested for the 2nd management channel." REFERENCE "Subclause 11.13.18.1 in IEEE Std 802.16-2004" ::= { wmanIf2BsRegisteredSsEntry 7 } wmanIf2BsSs2ndMgmtArqWindowSize OBJECT-TYPE SYNTAX INTEGER (1 .. 1024) MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the maximum number of unacknowledged fragments at any time for 2nd management connection." REFERENCE "Subclause 11.13.18.2 in IEEE Std 802.16-2004" ::= { wmanIf2BsRegisteredSsEntry 8 } wmanIf2BsSs2ndMgmtArqDnLinkTxDelay OBJECT-TYPE SYNTAX INTEGER (0 .. 65535) UNITS "us" MAX-ACCESS read-only STATUS current DESCRIPTION "The object defines the ARQ transmitter delay for downlink transmission." REFERENCE "Subclause 11.13.18.3 in IEEE Std 802.16-2004" ::= { wmanIf2BsRegisteredSsEntry 9 } wmanIf2BsSs2ndMgmtArqUpLinkTxDelay OBJECT-TYPE SYNTAX INTEGER (0 .. 65535) UNITS "us" MAX-ACCESS read-only STATUS current DESCRIPTION "The object defines the ARQ transmitter delay for uplink transmission." REFERENCE "Subclause 11.13.18.3 in IEEE Std 802.16-2004" ::= { wmanIf2BsRegisteredSsEntry 10 } wmanIf2BsSs2ndMgmtArqDnLinkRxDelay OBJECT-TYPE SYNTAX INTEGER (0 .. 65535) UNITS "us" MAX-ACCESS read-only STATUS current DESCRIPTION "The object defines the ARQ receiver delay for downlink transmission." REFERENCE "Subclause 11.13.18.3 in IEEE Std 802.16-2004" ::= { wmanIf2BsRegisteredSsEntry 11 } wmanIf2BsSs2ndMgmtArqUpLinkRxDelay OBJECT-TYPE SYNTAX INTEGER (0 .. 65535) UNITS "us" MAX-ACCESS read-only STATUS current DESCRIPTION "The object defines the ARQ receiver delay for uplink transmission." REFERENCE "Subclause 11.13.18.3 in IEEE Std 802.16-2004" ::= { wmanIf2BsRegisteredSsEntry 12 } wmanIf2BsSs2ndMgmtArqBlockLifetime OBJECT-TYPE SYNTAX INTEGER (0 .. 65535) UNITS "10 us" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum time interval an ARQ fragment will be managed by the transmitter ARQ machine, once initial transmission of the fragment has occured. If transmission or retransmission of the fragment is not acknowledged by the receiver before the time limit is reached, the fragment is discarded. A value of 0 means Infinite." REFERENCE "Subclause 11.13.18.4 in IEEE Std 802.16-2004" DEFVAL {0} ::= { wmanIf2BsRegisteredSsEntry 13 } wmanIf2BsSs2ndMgmtArqSyncLossTimeout OBJECT-TYPE SYNTAX INTEGER (0 .. 65535) UNITS "10 us" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum interval before declaring a loss of synchronization of the sender and receiver state machines. A value of 0 means Infinite." REFERENCE "Subclause 11.13.18.5 in IEEE Std 802.16-2004" DEFVAL {0} ::= { wmanIf2BsRegisteredSsEntry 14 } wmanIf2BsSs2ndMgmtArqDeliverInOrder OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether or not data is to be delivered by the receiving MAC to its client application in the order in which data was handed off to the originating MAC." REFERENCE "Subclause 11.13.18.6 in IEEE Std 802.16-2004" ::= { wmanIf2BsRegisteredSsEntry 15 } wmanIf2BsSs2ndMgmtArqRxPurgeTimeout OBJECT-TYPE SYNTAX INTEGER (0 .. 65535) UNITS "10 us" MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the time interval the ARQ window is advanced after a fragment is received. A value of 0 means Infinite." REFERENCE "Subclause 11.13.18.7 in IEEE Std 802.16-2004" DEFVAL {0} ::= { wmanIf2BsRegisteredSsEntry 16 } wmanIf2BsSs2ndMgmtArqBlockSize OBJECT-TYPE SYNTAX INTEGER (1 .. 2040) MAX-ACCESS read-only STATUS current DESCRIPTION "This parameter specifies the size of a ARQ block. This parameter shall be established by negotiation during the connection setup. The requester includes its desired setting in the REQ message. The receiver of the REQ message shall take the smaller of the value it prefers and value in the REQ message. The minimum value is included in the RSP message." REFERENCE "Subclause 11.13.18.8 in IEEE Std 802.16-2004" ::= { wmanIf2BsRegisteredSsEntry 17 } wmanIf2BsSsVendorIdEncoding OBJECT-TYPE SYNTAX OCTET STRING (SIZE(3)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value field contains the vendor identification specified by the 3 byte vendor-specific organizationally unique identifier of the SS or BS MAC address.A vendor ID used in a REG-REQ shall be the Vendor ID of the SS sending the request. A vendor ID used in a REG-RSP shall be the Vendor ID of the BS sending the response." REFERENCE "Subclause 11.1.5 in IEEE Std 802.16-2004" ::= { wmanIf2BsRegisteredSsEntry 18 } wmanIf2BsSsAasBroadcastPermission OBJECT-TYPE SYNTAX INTEGER {contBasedBwReqPermitted(0), contBasedBwReqNotPermitted(1)} MAX-ACCESS read-only STATUS current DESCRIPTION "This parameter specifies if SS can issue contention-based bandwidth request or not." REFERENCE "Subclause 11.6 in IEEE Std 802.16-2004" ::= { wmanIf2BsRegisteredSsEntry 19 } wmanIf2BsSsMaxTxPowerBpsk OBJECT-TYPE SYNTAX WmanIf2MaxTxPowerType MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum available power for BPSK. The maximum power parameters are reported in dBm and quantized in 0.5 dBm steps ranging from -64 dBm (encoded 0x00) to 63.5 dBm (encoded 0xFF). Values outside this range shall be assigned the closest extreme. This parameter is only applicable to systems supporting the SCa, OFDM or OFDMA PHY." REFERENCE "Subclause 11.8.3.2 in IEEE Std 802.16-2004" ::= { wmanIf2BsRegisteredSsEntry 20 } wmanIf2BsSsMaxTxPowerQpsk OBJECT-TYPE SYNTAX WmanIf2MaxTxPowerType MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum available power for QPSK. The maximum power parameters are reported in dBm and quantized in 0.5 dBm steps ranging from -64 dBm (encoded 0x00) to 63.5 dBm (encoded 0xFF). Values outside this range shall be assigned to closest extreme. This parameter is only applicable to systems supporting the SCa, OFDM or OFDMA PHY." REFERENCE "Subclause 11.8.3.2 in IEEE Std 802.16-2004" ::= { wmanIf2BsRegisteredSsEntry 21 } wmanIf2BsSsMaxTxPower16Qam OBJECT-TYPE SYNTAX WmanIf2MaxTxPowerType MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum available power for 16-QAM constellations. The maximum power parameters are reported in dBm and quantized in 0.5 dBm steps ranging from -64 dBm (encoded 0x00) to 63.5 dBm (encoded 0xFF). Values outside this range shall be assigned the closest extreme. This parameter is only applicable to systems supporting the SCa, OFDM or OFDMA PHY." REFERENCE "Subclause 11.8.3.2 in IEEE Std 802.16-2004" ::= { wmanIf2BsRegisteredSsEntry 22 } wmanIf2BsSsMaxTxPower64Qam OBJECT-TYPE SYNTAX WmanIf2MaxTxPowerType MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum available power for 64-QAM constellations. The maximum power parameters are reported in dBm and quantized in 0.5 dBm steps ranging from -64 dBm (encoded 0x00) to 63.5 dBm (encoded 0xFF). Values outside this range shall be assigned the closest extreme. SSs that do not support QAM64 shall report the value of 0x00. This parameter is only applicable to systems supporting the SCa, OFDM or OFDMA PHY." REFERENCE "Subclause 11.8.3.2 in IEEE Std 802.16-2004" ::= { wmanIf2BsRegisteredSsEntry 23 } wmanIf2BsSsMacVersion OBJECT-TYPE SYNTAX WmanIf2MacVersion MAX-ACCESS read-only STATUS current DESCRIPTION "This parameter specifies the version of 802.16 to which the message originator conforms." REFERENCE "Subclause 11.1.3 in IEEE Std 802.16-2004" ::= { wmanIf2BsRegisteredSsEntry 24 } -- -- wmanIf2BsConfigurationTable contains global parameters common in BS -- wmanIf2BsConfigurationTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2BsConfigurationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each BS sector that contains the BS system parameters as defined in Subclause 10.1 of [3]. The objects in this table define the default behaviour of the BS for 2nd Management connection scheduling and SFID allocation as well as configuration parameters of the CPS scheduler and AAS system." REFERENCE "Subclause 10.1 in IEEE Std 802.16-2004" ::= { wmanIf2BsCps 2 } wmanIf2BsConfigurationEntry OBJECT-TYPE SYNTAX WmanIf2BsConfigurationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is indexed by ifIndex with an ifType of propBWAp2Mp." INDEX { ifIndex } ::= { wmanIf2BsConfigurationTable 1 } WmanIf2BsConfigurationEntry ::= SEQUENCE { wmanIf2BsDcdInterval INTEGER, wmanIf2BsUcdInterval INTEGER, wmanIf2BsUcdTransition INTEGER, wmanIf2BsDcdTransition INTEGER, wmanIf2BsInitialRangingInterval INTEGER, wmanIf2BsSsULMapProcTime Unsigned32, wmanIf2BsSsRangRespProcTime Unsigned32, wmanIf2BsT5Timeout INTEGER, wmanIf2BsT9Timeout INTEGER, wmanIf2BsT13Timeout INTEGER, wmanIf2BsT15Timeout INTEGER, wmanIf2BsT17Timeout INTEGER, wmanIf2BsT27IdleTimer Unsigned32, wmanIf2BsT27ActiveTimer Unsigned32, wmanIf2Bs2ndMgmtDlQoSProfileIndex INTEGER, wmanIf2Bs2ndMgmtUlQoSProfileIndex INTEGER, wmanIf2BsAutoSfidEnabled INTEGER, wmanIf2BsAutoSfidRangeMin Unsigned32, wmanIf2BsAutoSfidRangeMax Unsigned32, wmanIf2BsAasChanFbckReqFreq INTEGER, wmanIf2BsAasBeamSelectFreq INTEGER, wmanIf2BsAasChanFbckReqResolution INTEGER, wmanIf2BsAasBeamReqResolution INTEGER, wmanIf2BsAasNumOptDiversityZones INTEGER, wmanIf2BsResetSector INTEGER} wmanIf2BsDcdInterval OBJECT-TYPE SYNTAX INTEGER (0..10000) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Time between transmission of DCD messages in ms." ::= { wmanIf2BsConfigurationEntry 1 } wmanIf2BsUcdInterval OBJECT-TYPE SYNTAX INTEGER (0..10000) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Time between transmission of UCD messages in ms." ::= { wmanIf2BsConfigurationEntry 2 } wmanIf2BsUcdTransition OBJECT-TYPE SYNTAX INTEGER (2..65535) UNITS "Number of MAC Frames" MAX-ACCESS read-write STATUS current DESCRIPTION "The time the BS shall wait after transmitting a UCD message with an incremented Configuration Change Count before issuing a UL-MAP message referring to Uplink_Burst_Profiles defined in that UCD message." ::= { wmanIf2BsConfigurationEntry 3 } wmanIf2BsDcdTransition OBJECT-TYPE SYNTAX INTEGER (2..65535) UNITS "Number of MAC Frames" MAX-ACCESS read-write STATUS current DESCRIPTION "The time the BS shall wait after transmitting a DCD message with an incremented Configuration Change Count before issuing a DL-MAP message referring to Downlink_Burst_Profiles defined in that DCD message." ::= { wmanIf2BsConfigurationEntry 4 } wmanIf2BsInitialRangingInterval OBJECT-TYPE SYNTAX INTEGER(0..2000) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Time between Initial Ranging regions assigned by the BS in ms." ::= { wmanIf2BsConfigurationEntry 5 } wmanIf2BsSsULMapProcTime OBJECT-TYPE SYNTAX Unsigned32 (200 .. 4294967295) UNITS "micro seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Time provided between arrival of the last bit of a UL-MAP at an SS and effectiveness of that map in us." ::= { wmanIf2BsConfigurationEntry 6 } wmanIf2BsSsRangRespProcTime OBJECT-TYPE SYNTAX Unsigned32 (10000 .. 4294967295) UNITS "micro seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Time allowed for an SS following receipt of a ranging response before it is expected to reply to an invited ranging request in us." ::= { wmanIf2BsConfigurationEntry 7 } wmanIf2BsT5Timeout OBJECT-TYPE SYNTAX INTEGER (0 .. 2000) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Wait for Uplink Channel Change Response in ms." ::= { wmanIf2BsConfigurationEntry 8 } wmanIf2BsT9Timeout OBJECT-TYPE SYNTAX INTEGER (300 .. 65535) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Registration Timeout, the time allowed between the BS sending a RNG-RSP (success) to an SS, and receiving a SBC-REQ from that same SS in ms." ::= { wmanIf2BsConfigurationEntry 9 } wmanIf2BsT13Timeout OBJECT-TYPE SYNTAX INTEGER (15 .. 65535) UNITS "minutes" MAX-ACCESS read-write STATUS current DESCRIPTION "The time allowed for an SS, following receipt of a REG-RSP message to send a TFTP-CPLT message to the BS in min." ::= { wmanIf2BsConfigurationEntry 10 } wmanIf2BsT15Timeout OBJECT-TYPE SYNTAX INTEGER (20 .. 65535) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Wait for MCA-RSP in ms." ::= { wmanIf2BsConfigurationEntry 11 } wmanIf2BsT17Timeout OBJECT-TYPE SYNTAX INTEGER (5 .. 65535) UNITS "minutes" MAX-ACCESS read-write STATUS current DESCRIPTION "Time allowed for SS to complete SS Authorization and Key Exchange in minutes." ::= { wmanIf2BsConfigurationEntry 12 } wmanIf2BsT27IdleTimer OBJECT-TYPE SYNTAX Unsigned32 (10000 .. 4294967295) UNITS "us" MAX-ACCESS read-write STATUS current DESCRIPTION "Maximum time between unicast grants to SS when BS believes SS uplink transmission quality is good enough." ::= { wmanIf2BsConfigurationEntry 13 } wmanIf2BsT27ActiveTimer OBJECT-TYPE SYNTAX Unsigned32 (10000 .. 4294967295) UNITS "us" MAX-ACCESS read-write STATUS current DESCRIPTION "Maximum time between unicast grants to SS when BS believes SS uplink transmission quality is not good enough." ::= { wmanIf2BsConfigurationEntry 14 } wmanIf2Bs2ndMgmtDlQoSProfileIndex OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "This object defines the index of a row in wmanIf2BsServiceClassTable which is used to obtain all QoS parameters required for the BS downlink scheduler to properly allocate and manage the bandwidth and schedule the 2nd Management Connection traffic. The 2nd Management Connection traffic doesn't differ from Traffic Connection traffic in the area of QoS management." ::= { wmanIf2BsConfigurationEntry 15 } wmanIf2Bs2ndMgmtUlQoSProfileIndex OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "This object defines the index of a row in wmanIf2BsServiceClassTable which is used to obtain all QoS parameters required for the BS uplink scheduler to properly allocate and manage the bandwidth and schedule the 2nd Management Connection traffic. The 2nd Management Connection traffic doesn't differ from Traffic Connection traffic in the area of QoS management." ::= { wmanIf2BsConfigurationEntry 16 } wmanIf2BsAutoSfidEnabled OBJECT-TYPE SYNTAX INTEGER {autoSfidDisabled(0), autoSfidEnabled(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "This object defines whether the BS is allowed to autonomously allocate SFIDs. When the object is set to autoSfidEnabled, the BS is allowed to autonomously allocate SFIDs from the range of allowed values defined by wmanIf2BsConfigExtAutoSfidRangeMin and wmanIf2BsConfigExtAutoSfidRangeMax. A SF is created autonomously when it has not been provisioned in the wmanIf2BsProvisionedSfTable and may be initiated by either the SS or BS. The BS should always initiate SF creation based on the provisioned Service flows configured in wmanIf2BsProvisionedSfTable." REFERENCE "Subclause 11.13.1 in IEEE Std 802.16-2004" ::= { wmanIf2BsConfigurationEntry 17 } wmanIf2BsAutoSfidRangeMin OBJECT-TYPE SYNTAX Unsigned32 ( 1 .. 4294967295) MAX-ACCESS read-write STATUS current DESCRIPTION "This object defines the minimum value of the range of SFID values allocated for the BS sector for the purpose of autonomous creation of service flows. This value is used when the object wmanIf2BsAutoSfidEnabled allows autonomous creation of SFIDs." REFERENCE "Subclause 11.13.1 in IEEE Std 802.16-2004" ::= { wmanIf2BsConfigurationEntry 18 } wmanIf2BsAutoSfidRangeMax OBJECT-TYPE SYNTAX Unsigned32 ( 1 .. 4294967295) MAX-ACCESS read-write STATUS current DESCRIPTION "This object defines the maximum value of the range of SFID values allocated for the BS sector for the purpose of autonomous creation of the service flows. This value is used when the object wmanIf2BsAutoSfidEnabled allows autonomous creation of SFIDs." REFERENCE "Subclause 11.13.1 in IEEE Std 802.16-2004" ::= { wmanIf2BsConfigurationEntry 19 } wmanIf2BsAasChanFbckReqFreq OBJECT-TYPE SYNTAX INTEGER (5..10000) UNITS "ms" MAX-ACCESS read-write STATUS current DESCRIPTION "This object defines AAS channel feedback request frequency. It controls the frequency of downlink beam measurements. The relevant MAC messages are AAS-FBCK-REQ/RSP" REFERENCE "Subclause 6.3.2.3.40 in IEEE Std 802.16-2004" ::= { wmanIf2BsConfigurationEntry 20 } wmanIf2BsAasBeamSelectFreq OBJECT-TYPE SYNTAX INTEGER (5..10000) UNITS "ms" MAX-ACCESS read-write STATUS current DESCRIPTION "This object defines AAS beam select frequency. It controls how often SS issues beam select messages. The relevant MAC message is AAS_Beam_Select" REFERENCE "Subclause 6.3.2.3.41 in IEEE Std 802.16-2004" ::= { wmanIf2BsConfigurationEntry 21 } wmanIf2BsAasChanFbckReqResolution OBJECT-TYPE SYNTAX INTEGER {aasChanFbckRes00(0), aasChanFbckRes01(1), aasChanFbckRes10(2), aasChanFbckRes11(3)} MAX-ACCESS read-write STATUS current DESCRIPTION "This object defines AAS feedback request frequency measurements resolution. It is coded as follows: aasChanFbckRes00 - every 4th carrier (-100, -96, -92, .., 100) aasChanFbckRes01 - every 8th carrier (-100, -92, -84, .., 100) aasChanFbckRes10 - every 16th carrier (-100, -84, -68, .., 100) aasChanFbckRes11 - every 32th carrier (-100, -68, -36, .., 100)" REFERENCE "Subclause 8.3.6.4 in IEEE Std 802.16-2004" ::= { wmanIf2BsConfigurationEntry 22 } wmanIf2BsAasBeamReqResolution OBJECT-TYPE SYNTAX INTEGER {aasBeamReqRes000(0), aasBeamReqRes001(1), aasBeamReqRes010(2), aasBeamReqRes011(3), aasBeamReqRes100(4)} MAX-ACCESS read-write STATUS current DESCRIPTION "This object defines AAS beam select request resolution parameter. It is coded as follows: aasBeamReqRes000 - every 4th carrier aasBeamReqRes001 - every 8th carrier aasBeamReqRes010 - every 16th carrier aasBeamReqRes011 - every 32th carrier aasBeamReqRes100 - every 64th carrier" REFERENCE "Subclause 8.3.6.5 in IEEE Std 802.16-2004" ::= { wmanIf2BsConfigurationEntry 23 } wmanIf2BsAasNumOptDiversityZones OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "This object defines the number of optional diversity zones transmitted in downlink." REFERENCE "Figure 209 in IEEE Std 802.16-2004" ::= { wmanIf2BsConfigurationEntry 24 } wmanIf2BsResetSector OBJECT-TYPE SYNTAX INTEGER {actionResetSectorNoAction(0), actionResetSector(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "This object should be implemented as follows: - When set to actionsResetSector value, instructs BS to reset the sector identified by ifIndex. As a result of this action the Phy and Mac of this sector should be reinitialised. - When set to value different than actionsResetSector it should be ignored - When read it should return actionsResetSectorNoAction" ::= { wmanIf2BsConfigurationEntry 25 } -- -- Base Station Channel Measurement Table -- wmanIf2BsChannelMeasurementTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2BsChannelMeasurementEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains channel measurement information as derived from BS measurement of uplink signal from SS, and the downlink signal as reported from SS using REP-REQ/RSP messages. The table shall be maintained as FIFO to store measurement samples that can be used to create RSSI and CINR histogram report. When the measurement entry for a SS reaches the limit, the oldest entry shall be deleted as the new entry is added to the table." REFERENCE "6.3.2.3.33 in IEEE Std 802.16-2004" ::= { wmanIf2BsCps 3 } wmanIf2BsChannelMeasurementEntry OBJECT-TYPE SYNTAX WmanIf2BsChannelMeasurementEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in the table contains RSSI and CINR signal quality measurement on signal received from the SS. The primary index is the ifIndex with ifType of propBWAp2Mp identifing the BS sector. wmanIf2BsSsMacAddress identifies the SS from which the signal was received. wmanIf2BsChannelDirection is the index to the direction of the channel. wmanIf2BsHistogramIndex is the index to histogram samples. Since there is no time stamp in the table, wmanIf2BsHistogramIndex should be increased monotonically, and wraps around when it reaches the implementation specific limit." INDEX { ifIndex, wmanIf2BsSsMacAddress, wmanIf2BsChannelDirection, wmanIf2BsHistogramIndex } ::= { wmanIf2BsChannelMeasurementTable 1 } WmanIf2BsChannelMeasurementEntry ::= SEQUENCE { wmanIf2BsChannelDirection INTEGER, wmanIf2BsHistogramIndex Unsigned32, wmanIf2BsChannelNumber WmanIf2ChannelNumber, wmanIf2BsStartFrame INTEGER, wmanIf2BsDuration INTEGER, wmanIf2BsBasicReport BITS, wmanIf2BsMeanCinrReport INTEGER, wmanIf2BsMeanRssiReport INTEGER, wmanIf2BsStdDeviationCinrReport INTEGER, wmanIf2BsStdDeviationRssiReport INTEGER} wmanIf2BsChannelDirection OBJECT-TYPE SYNTAX INTEGER {downstream(1), upstream(2)} MAX-ACCESS not-accessible STATUS current DESCRIPTION "wmanIf2BsChannelDirection identifies the direction of a a channel where the measurement takes place." ::= { wmanIf2BsChannelMeasurementEntry 1 } wmanIf2BsHistogramIndex OBJECT-TYPE SYNTAX Unsigned32 (1 .. 4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "wmanIf2BsHistogramIndex identifies the histogram samples in the table for each subscriber station." ::= { wmanIf2BsChannelMeasurementEntry 2 } wmanIf2BsChannelNumber OBJECT-TYPE SYNTAX WmanIf2ChannelNumber MAX-ACCESS read-only STATUS current DESCRIPTION "Physical channel number to be reported on is only applicable to license exempt band. For licensed band, this parameter should be null." REFERENCE "Subclause 11.12 in IEEE Std 802.16-2004" ::= { wmanIf2BsChannelMeasurementEntry 3 } wmanIf2BsStartFrame OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Frame number in which measurement for this channel started." REFERENCE "Subclause 11.12 in IEEE Std 802.16-2004" ::= { wmanIf2BsChannelMeasurementEntry 4 } wmanIf2BsDuration OBJECT-TYPE SYNTAX INTEGER (0 .. 16777215) MAX-ACCESS read-only STATUS current DESCRIPTION "Cumulative measurement duration on the channel in multiples of Ts. For any value exceeding 0xFFFFFF, report 0xFFFFFF." REFERENCE "Subclause 11.12 in IEEE Std 802.16-2004" ::= { wmanIf2BsChannelMeasurementEntry 5 } wmanIf2BsBasicReport OBJECT-TYPE SYNTAX BITS {wirelessHuman(0), unknownTransmission(1), primaryUser(2), channelNotMeasured(3)} MAX-ACCESS read-only STATUS current DESCRIPTION "Bit #0: WirelessHUMAN detected on the channel Bit #1: Unknown transmissions detected on the channel Bit #2: Primary User detected on the channel Bit #3: Unmeasured. Channel not measured" REFERENCE "Subclause 11.12 in IEEE Std 802.16-2004" ::= { wmanIf2BsChannelMeasurementEntry 6 } wmanIf2BsMeanCinrReport OBJECT-TYPE SYNTAX INTEGER (0 .. 41) UNITS "dB" MAX-ACCESS read-only STATUS current DESCRIPTION "Mean CINR report." REFERENCE "Subclause 8.2.2, 8.3.9 in IEEE Std 802.16-2004" ::= { wmanIf2BsChannelMeasurementEntry 7 } wmanIf2BsMeanRssiReport OBJECT-TYPE SYNTAX INTEGER (0 .. 83) UNITS "dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "Mean RSSI report." REFERENCE "Subclause 8.2.2, 8.3.9 in IEEE Std 802.16-2004" ::= { wmanIf2BsChannelMeasurementEntry 8 } wmanIf2BsStdDeviationCinrReport OBJECT-TYPE SYNTAX INTEGER (0 .. 41) UNITS "dB" MAX-ACCESS read-only STATUS current DESCRIPTION "Standard deviation CINR report." REFERENCE "Subclause 8.2.2, 8.3.9 in IEEE Std 802.16-2004" ::= { wmanIf2BsChannelMeasurementEntry 9 } wmanIf2BsStdDeviationRssiReport OBJECT-TYPE SYNTAX INTEGER (0 .. 83) UNITS "dB" MAX-ACCESS read-only STATUS current DESCRIPTION "Standard deviation RSSI report." REFERENCE "Subclause 8.2.2, 8.3.9 in IEEE Std 802.16-2004" ::= { wmanIf2BsChannelMeasurementEntry 10 } -- -- Base Station capabilities -- wmanIf2BsCapabilities OBJECT IDENTIFIER ::= { wmanIf2BsCps 4 } wmanIf2BsSsReqCapabilitiesTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2BsSsReqCapabilitiesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the basic capability information of SSs that have been reported by SSs to BS using RNG-REQ, SBC-REQ and REG-REQ messages. Entries in this table should be created when an SS registers with a BS." ::= { wmanIf2BsCapabilities 1 } wmanIf2BsSsReqCapabilitiesEntry OBJECT-TYPE SYNTAX WmanIf2BsSsReqCapabilitiesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each SS that has been registered in the BS. This table augments the table wmanIf2BsRegisteredSsTable." AUGMENTS { wmanIf2BsRegisteredSsEntry } ::= { wmanIf2BsSsReqCapabilitiesTable 1 } WmanIf2BsSsReqCapabilitiesEntry ::= SEQUENCE { wmanIf2BsSsReqCapUplinkCidSupport WmanIf2eNumOfCid, wmanIf2BsSsReqCapArqSupport WmanIf2ArqSupportType, wmanIf2BsSsReqCapDsxFlowControl WmanIf2MaxDsxFlowType, wmanIf2BsSsReqCapMacCrcSupport WmanIf2MacCrcSupport, wmanIf2BsSsReqCapMcaFlowControl WmanIf2MaxMcaFlowType, wmanIf2BsSsReqCapMcpGroupCidSupport WmanIf2MaxMcpGroupCid, wmanIf2BsSsReqCapPkmFlowControl WmanIf2MaxPkmFlowType, wmanIf2BsSsReqCapAuthPolicyControl WmanIf2AuthPolicyType, wmanIf2BsSsReqCapMaxNumOfSupportedSA WmanIf2MaxNumOfSaType, wmanIf2BsSsReqCapIpVersion WmanIf2IpVersionType, wmanIf2BsSsReqCapMacCsSupportBitMap WmanIf2MacCsBitMap, wmanIf2BsSsReqCapMaxNumOfClassifier WmanIf2MaxClassifiers, wmanIf2BsSsReqCapPhsSupport WmanIf2PhsSupportType, wmanIf2BsSsReqCapBandwidthAllocSupport WmanIf2BwAllocSupport, wmanIf2BsSsReqCapPduConstruction WmanIf2PduConstruction, wmanIf2BsSsReqCapTtgTransitionGap WmanIf2SsTransitionGap, wmanIf2BsSsReqCapRtgTransitionGap WmanIf2SsTransitionGap} wmanIf2BsSsReqCapUplinkCidSupport OBJECT-TYPE SYNTAX WmanIf2eNumOfCid MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the number of Uplink CIDs the SS can support." ::= { wmanIf2BsSsReqCapabilitiesEntry 1 } wmanIf2BsSsReqCapArqSupport OBJECT-TYPE SYNTAX WmanIf2ArqSupportType MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether the SS supports ARQ." ::= { wmanIf2BsSsReqCapabilitiesEntry 2 } wmanIf2BsSsReqCapDsxFlowControl OBJECT-TYPE SYNTAX WmanIf2MaxDsxFlowType MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the maximum number of concurrent DSA, DSC, or DSD transactions that SS is capable of having outstanding." DEFVAL { 0 } ::= { wmanIf2BsSsReqCapabilitiesEntry 3 } wmanIf2BsSsReqCapMacCrcSupport OBJECT-TYPE SYNTAX WmanIf2MacCrcSupport MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether or not the SS supports MAC level CRC." DEFVAL { macCrcSupport } ::= { wmanIf2BsSsReqCapabilitiesEntry 4 } wmanIf2BsSsReqCapMcaFlowControl OBJECT-TYPE SYNTAX WmanIf2MaxMcaFlowType MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the maximum number of concurrent MCA transactions that SS is capable of having outstanding." DEFVAL { 0 } ::= { wmanIf2BsSsReqCapabilitiesEntry 5 } wmanIf2BsSsReqCapMcpGroupCidSupport OBJECT-TYPE SYNTAX WmanIf2MaxMcpGroupCid MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the maximum number of simultaneous Multicast Polling Groups the SS is capable of belonging to." DEFVAL { 0 } ::= { wmanIf2BsSsReqCapabilitiesEntry 6 } wmanIf2BsSsReqCapPkmFlowControl OBJECT-TYPE SYNTAX WmanIf2MaxPkmFlowType MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the maximum number of concurrent PKM transactions that SS is capable of having outstanding." DEFVAL { 0 } ::= { wmanIf2BsSsReqCapabilitiesEntry 7 } wmanIf2BsSsReqCapAuthPolicyControl OBJECT-TYPE SYNTAX WmanIf2AuthPolicyType MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies authorization policy that SS is capable of. A bit value of 0 = 'not supported', 1 = 'supported'. If this field is omitted, then both SS and BS shall use the IEEE 802.16 security, constituting X.509 digital certificates and the RSA public key encryption algorithm, as authorization policy." ::= { wmanIf2BsSsReqCapabilitiesEntry 8 } wmanIf2BsSsReqCapMaxNumOfSupportedSA OBJECT-TYPE SYNTAX WmanIf2MaxNumOfSaType MAX-ACCESS read-only STATUS current DESCRIPTION "This field specifies the maximum number of supported security associations of the SS." DEFVAL { 1 } ::= { wmanIf2BsSsReqCapabilitiesEntry 9 } wmanIf2BsSsReqCapIpVersion OBJECT-TYPE SYNTAX WmanIf2IpVersionType MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the version of IP used on the 2nd Management Connection. The value should be undefined if the 2nd management CID doesn't exist." ::= { wmanIf2BsSsReqCapabilitiesEntry 10 } wmanIf2BsSsReqCapMacCsSupportBitMap OBJECT-TYPE SYNTAX WmanIf2MacCsBitMap MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates SS reported set of MAC convergence sublayer support. When a bit is set, it indicates the corresponding CS feature is supported." ::= { wmanIf2BsSsReqCapabilitiesEntry 11 } wmanIf2BsSsReqCapMaxNumOfClassifier OBJECT-TYPE SYNTAX WmanIf2MaxClassifiers MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the maximum number of admitted Classifiers that the SS can support." DEFVAL { 0 } ::= { wmanIf2BsSsReqCapabilitiesEntry 12 } wmanIf2BsSsReqCapPhsSupport OBJECT-TYPE SYNTAX WmanIf2PhsSupportType MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates indicates the level of SS support for PHS." DEFVAL { noPhsSupport } ::= { wmanIf2BsSsReqCapabilitiesEntry 13 } wmanIf2BsSsReqCapBandwidthAllocSupport OBJECT-TYPE SYNTAX WmanIf2BwAllocSupport MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the bandwidth allocation capabilities of the SS. The usage is defined by WmanIf2BwAllocSupport." ::= { wmanIf2BsSsReqCapabilitiesEntry 14 } wmanIf2BsSsReqCapPduConstruction OBJECT-TYPE SYNTAX WmanIf2PduConstruction MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the SS's capabilities for construction and transmission of MAC PDUs. The usage is defined by WmanIf2PduConstruction." ::= { wmanIf2BsSsReqCapabilitiesEntry 15 } wmanIf2BsSsReqCapTtgTransitionGap OBJECT-TYPE SYNTAX WmanIf2SsTransitionGap UNITS "us" MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the SS's transition speed SSTTG for TDD and H-FDD SSs. The usage is defined by WmanIf2SsTransitionGap." ::= { wmanIf2BsSsReqCapabilitiesEntry 16 } wmanIf2BsSsReqCapRtgTransitionGap OBJECT-TYPE SYNTAX WmanIf2SsTransitionGap UNITS "us" MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the SS's transition speed SSRTG for TDD and H-FDD SSs. The usage is defined by WmanIf2SsTransitionGap." ::= { wmanIf2BsSsReqCapabilitiesEntry 17 } wmanIf2BsSsRspCapabilitiesTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2BsSsRspCapabilitiesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the basic capability information of SSs that have been negotiated and agreed between BS and SS via RNG-REQ/RSP, SBC-REQ/RSP and REG-REQ/RSP messages. This table augments the wmanIf2BsRegisteredSsTable." REFERENCE "Subclause 6.3.2.3.7 in IEEE Std 802.16-2004" ::= { wmanIf2BsCapabilities 2 } wmanIf2BsSsRspCapabilitiesEntry OBJECT-TYPE SYNTAX WmanIf2BsSsRspCapabilitiesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each SS that has been registered in the BS. This table augments the wmanIf2BsRegisteredSsTable. " AUGMENTS { wmanIf2BsRegisteredSsEntry } ::= { wmanIf2BsSsRspCapabilitiesTable 1 } WmanIf2BsSsRspCapabilitiesEntry ::= SEQUENCE { wmanIf2BsSsRspCapUplinkCidSupport WmanIf2eNumOfCid, wmanIf2BsSsRspCapArqSupport WmanIf2ArqSupportType, wmanIf2BsSsRspCapDsxFlowControl WmanIf2MaxDsxFlowType, wmanIf2BsSsRspCapMacCrcSupport WmanIf2MacCrcSupport, wmanIf2BsSsRspCapMcaFlowControl WmanIf2MaxMcaFlowType, wmanIf2BsSsRspCapMcpGroupCidSupport WmanIf2MaxMcpGroupCid, wmanIf2BsSsRspCapPkmFlowControl WmanIf2MaxPkmFlowType, wmanIf2BsSsRspCapAuthPolicyControl WmanIf2AuthPolicyType, wmanIf2BsSsRspCapMaxNumOfSupportedSA WmanIf2MaxNumOfSaType, wmanIf2BsSsRspCapIpVersion WmanIf2IpVersionType, wmanIf2BsSsRspCapMacCsSupportBitMap WmanIf2MacCsBitMap, wmanIf2BsSsRspCapMaxNumOfClassifier WmanIf2MaxClassifiers, wmanIf2BsSsRspCapPhsSupport WmanIf2PhsSupportType, wmanIf2BsSsRspCapBandwidthAllocSupport WmanIf2BwAllocSupport, wmanIf2BsSsRspCapPduConstruction WmanIf2PduConstruction, wmanIf2BsSsRspCapTtgTransitionGap WmanIf2SsTransitionGap, wmanIf2BsSsRspCapRtgTransitionGap WmanIf2SsTransitionGap} wmanIf2BsSsRspCapUplinkCidSupport OBJECT-TYPE SYNTAX WmanIf2eNumOfCid MAX-ACCESS read-only STATUS current DESCRIPTION "Negotiated number of Uplink CIDs the SS can support." ::= { wmanIf2BsSsRspCapabilitiesEntry 1 } wmanIf2BsSsRspCapArqSupport OBJECT-TYPE SYNTAX WmanIf2ArqSupportType MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether the SS is allowed to use ARQ as a result of the capabilities negotiation." ::= { wmanIf2BsSsRspCapabilitiesEntry 2 } wmanIf2BsSsRspCapDsxFlowControl OBJECT-TYPE SYNTAX WmanIf2MaxDsxFlowType MAX-ACCESS read-only STATUS current DESCRIPTION "Negotiated maximum number of concurrent DSA, DSC, or DSD transactions that may be outstanding." ::= { wmanIf2BsSsRspCapabilitiesEntry 3 } wmanIf2BsSsRspCapMacCrcSupport OBJECT-TYPE SYNTAX WmanIf2MacCrcSupport MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether or not the SS is allowed to use MAC level CRC as a result of the capabilities negotiation." DEFVAL { macCrcSupport } ::= { wmanIf2BsSsRspCapabilitiesEntry 4 } wmanIf2BsSsRspCapMcaFlowControl OBJECT-TYPE SYNTAX WmanIf2MaxMcaFlowType MAX-ACCESS read-only STATUS current DESCRIPTION "Negotiated maximum number of concurrent MCA transactions that may be outstanding." DEFVAL { 0 } ::= { wmanIf2BsSsRspCapabilitiesEntry 5 } wmanIf2BsSsRspCapMcpGroupCidSupport OBJECT-TYPE SYNTAX WmanIf2MaxMcpGroupCid MAX-ACCESS read-only STATUS current DESCRIPTION "Negotiated maximum number of simultaneous Multicast Polling Groups the SS is capable of belonging to." DEFVAL { 0 } ::= { wmanIf2BsSsRspCapabilitiesEntry 6 } wmanIf2BsSsRspCapPkmFlowControl OBJECT-TYPE SYNTAX WmanIf2MaxPkmFlowType MAX-ACCESS read-only STATUS current DESCRIPTION "Negotiated maximum number of concurrent PKM transactions that may be outstanding." DEFVAL { 0 } ::= { wmanIf2BsSsRspCapabilitiesEntry 7 } wmanIf2BsSsRspCapAuthPolicyControl OBJECT-TYPE SYNTAX WmanIf2AuthPolicyType MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies negotiated authorization policy. A bit value of 0 = 'not supported', 1 = 'supported'. If this field is omitted, then both SS and BS shall use the IEEE 802.16 security, constituting X.509 digital certificates and the RSA public key encryption algorithm, as authorization policy." ::= { wmanIf2BsSsRspCapabilitiesEntry 8 } wmanIf2BsSsRspCapMaxNumOfSupportedSA OBJECT-TYPE SYNTAX WmanIf2MaxNumOfSaType MAX-ACCESS read-only STATUS current DESCRIPTION "Negotiated maximum number of supported security association of the SS." DEFVAL { 1 } ::= { wmanIf2BsSsRspCapabilitiesEntry 9 } wmanIf2BsSsRspCapIpVersion OBJECT-TYPE SYNTAX WmanIf2IpVersionType MAX-ACCESS read-only STATUS current DESCRIPTION "Negotiated version of IP used on the 2nd Management Connection. The value should be undefined if the 2nd management CID doesn't exist." ::= { wmanIf2BsSsRspCapabilitiesEntry 10 } wmanIf2BsSsRspCapMacCsSupportBitMap OBJECT-TYPE SYNTAX WmanIf2MacCsBitMap MAX-ACCESS read-only STATUS current DESCRIPTION "Negotiated set of MAC convergence sublayer support. When a bit is set, it indicates the corresponding CS feature is supported." ::= { wmanIf2BsSsRspCapabilitiesEntry 11 } wmanIf2BsSsRspCapMaxNumOfClassifier OBJECT-TYPE SYNTAX WmanIf2MaxClassifiers MAX-ACCESS read-only STATUS current DESCRIPTION "Negotiated maximum number of admitted Classifiers that the SS is allowed to have." DEFVAL { 0 } ::= { wmanIf2BsSsRspCapabilitiesEntry 12 } wmanIf2BsSsRspCapPhsSupport OBJECT-TYPE SYNTAX WmanIf2PhsSupportType MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the negotiated level of PHS support." DEFVAL { noPhsSupport } ::= { wmanIf2BsSsRspCapabilitiesEntry 13 } wmanIf2BsSsRspCapBandwidthAllocSupport OBJECT-TYPE SYNTAX WmanIf2BwAllocSupport MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates negotiated properties of the SS for bandwidth allocation purposes. The usage is defined by WmanIf2BwAllocSupport." ::= { wmanIf2BsSsRspCapabilitiesEntry 14 } wmanIf2BsSsRspCapPduConstruction OBJECT-TYPE SYNTAX WmanIf2PduConstruction MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies negotiated capabilities for construction and transmission of MAC PDUs. The usage is defined by WmanIf2PduConstruction." ::= { wmanIf2BsSsRspCapabilitiesEntry 15 } wmanIf2BsSsRspCapTtgTransitionGap OBJECT-TYPE SYNTAX WmanIf2SsTransitionGap UNITS "us" MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the negotiated transition speed SSTTG for TDD and H-FDD SSs. The usage is defined by WmanIf2SsTransitionGap." ::= { wmanIf2BsSsRspCapabilitiesEntry 16 } wmanIf2BsSsRspCapRtgTransitionGap OBJECT-TYPE SYNTAX WmanIf2SsTransitionGap UNITS "us" MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the negotiated transition speed SSRTG for TDD and H-FDD SSs. The usage is defined by WmanIf2SsTransitionGap." ::= { wmanIf2BsSsRspCapabilitiesEntry 17 } wmanIf2BsBasicCapabilitiesTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2BsBasicCapabilitiesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the basic capabilities of the BS as implemented in BS hardware and software. These capabilities along with the configuration for them (wmanIf2BsCapabilitiesConfigTable) are used for negotiation of basic capabilities with SS using RNG-RSP, SBC-RSP and REG-RSP messages. The negotiated capabilities are obtained by interSubclause of SS raw reported capabilities, BS raw capabilities and BS configured capabilities. The objects in the table have read-only access. The table is maintained by BS." ::= { wmanIf2BsCapabilities 3 } wmanIf2BsBasicCapabilitiesEntry OBJECT-TYPE SYNTAX WmanIf2BsBasicCapabilitiesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each BS sector and is indexed by ifIndex." INDEX { ifIndex } ::= { wmanIf2BsBasicCapabilitiesTable 1 } WmanIf2BsBasicCapabilitiesEntry ::= SEQUENCE { wmanIf2BsCapUplinkCidSupport WmanIf2eNumOfCid, wmanIf2BsCapArqSupport WmanIf2ArqSupportType, wmanIf2BsCapDsxFlowControl WmanIf2MaxDsxFlowType, wmanIf2BsCapMacCrcSupport WmanIf2MacCrcSupport, wmanIf2BsCapMcaFlowControl WmanIf2MaxMcaFlowType, wmanIf2BsCapMcpGroupCidSupport WmanIf2MaxMcpGroupCid, wmanIf2BsCapPkmFlowControl WmanIf2MaxPkmFlowType, wmanIf2BsCapAuthPolicyControl WmanIf2AuthPolicyType, wmanIf2BsCapMaxNumOfSupportedSA WmanIf2MaxNumOfSaType, wmanIf2BsCapIpVersion WmanIf2IpVersionType, wmanIf2BsCapMacCsSupportBitMap WmanIf2MacCsBitMap, wmanIf2BsCapMaxNumOfClassifier WmanIf2MaxClassifiers, wmanIf2BsCapPhsSupport WmanIf2PhsSupportType, wmanIf2BsCapBandwidthAllocSupport WmanIf2BwAllocSupport, wmanIf2BsCapPduConstruction WmanIf2PduConstruction, wmanIf2BsCapTtgTransitionGap WmanIf2SsTransitionGap, wmanIf2BsCapRtgTransitionGap WmanIf2SsTransitionGap} wmanIf2BsCapUplinkCidSupport OBJECT-TYPE SYNTAX WmanIf2eNumOfCid MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the number of Uplink CIDs the BS can support per SS." ::= { wmanIf2BsBasicCapabilitiesEntry 1 } wmanIf2BsCapArqSupport OBJECT-TYPE SYNTAX WmanIf2ArqSupportType MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether the BS supports ARQ." ::= { wmanIf2BsBasicCapabilitiesEntry 2 } wmanIf2BsCapDsxFlowControl OBJECT-TYPE SYNTAX WmanIf2MaxDsxFlowType MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the maximum number of concurrent DSA, DSC, or DSD transactions that BS allows each SS to have outstanding." DEFVAL { 0 } ::= { wmanIf2BsBasicCapabilitiesEntry 3 } wmanIf2BsCapMacCrcSupport OBJECT-TYPE SYNTAX WmanIf2MacCrcSupport MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether or not the BS supports MAC level CRC." DEFVAL { macCrcSupport } ::= { wmanIf2BsBasicCapabilitiesEntry 4 } wmanIf2BsCapMcaFlowControl OBJECT-TYPE SYNTAX WmanIf2MaxMcaFlowType MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the maximum number of concurrent MCA transactions that BS allows each SS to have." DEFVAL { 0 } ::= { wmanIf2BsBasicCapabilitiesEntry 5 } wmanIf2BsCapMcpGroupCidSupport OBJECT-TYPE SYNTAX WmanIf2MaxMcpGroupCid MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the maximum number of simultaneous Multicast Polling Groups the BS allows each SS to belong to." DEFVAL { 0 } ::= { wmanIf2BsBasicCapabilitiesEntry 6 } wmanIf2BsCapPkmFlowControl OBJECT-TYPE SYNTAX WmanIf2MaxPkmFlowType MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the maximum number of concurrent PKM transactions that BS allows each SS to have." DEFVAL { 0 } ::= { wmanIf2BsBasicCapabilitiesEntry 7 } wmanIf2BsCapAuthPolicyControl OBJECT-TYPE SYNTAX WmanIf2AuthPolicyType MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies authorization policy that BS is capable of. A bit value of 0 = 'not supported', 1 = 'supported'. If this field is omitted, then both SS and BS shall use the IEEE 802.16 security, constituting X.509 digital certificates and the RSA public key encryption algorithm, as authorization policy." ::= { wmanIf2BsBasicCapabilitiesEntry 8 } wmanIf2BsCapMaxNumOfSupportedSA OBJECT-TYPE SYNTAX WmanIf2MaxNumOfSaType MAX-ACCESS read-only STATUS current DESCRIPTION "This field specifies maximum number of supported security associations per SS that the BS allows." DEFVAL { 1 } ::= { wmanIf2BsBasicCapabilitiesEntry 9 } wmanIf2BsCapIpVersion OBJECT-TYPE SYNTAX WmanIf2IpVersionType MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the version of IP BS allows each SS to use on the 2nd Management Connection. The value 'undefined' should not be used for this field." REFERENCE "Subclause 11.7.4 in IEEE Std 802.16-2004" ::= { wmanIf2BsBasicCapabilitiesEntry 10 } wmanIf2BsCapMacCsSupportBitMap OBJECT-TYPE SYNTAX WmanIf2MacCsBitMap MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates BS set of MAC convergence sublayer support. When a bit is set, it indicates the corresponding CS feature is supported." ::= { wmanIf2BsBasicCapabilitiesEntry 11 } wmanIf2BsCapMaxNumOfClassifier OBJECT-TYPE SYNTAX WmanIf2MaxClassifiers MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the maximum number of admitted Classifiers per SS that the BS allows." DEFVAL { 0 } ::= { wmanIf2BsBasicCapabilitiesEntry 12 } wmanIf2BsCapPhsSupport OBJECT-TYPE SYNTAX WmanIf2PhsSupportType MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the level of BS support for PHS. The usage is defined by WmanIf2PhsSupportType." DEFVAL { noPhsSupport } ::= { wmanIf2BsBasicCapabilitiesEntry 13 } wmanIf2BsCapBandwidthAllocSupport OBJECT-TYPE SYNTAX WmanIf2BwAllocSupport MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the bandwidth allocation properties that the BS permits SSs to use. The usage is defined by WmanIf2BwAllocSupport." ::= { wmanIf2BsBasicCapabilitiesEntry 14 } wmanIf2BsCapPduConstruction OBJECT-TYPE SYNTAX WmanIf2PduConstruction MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the capabilities for construction and transmission of MAC PDUs allowed by the BS. The usage is defined by WmanIf2PduConstruction." ::= { wmanIf2BsBasicCapabilitiesEntry 15 } wmanIf2BsCapTtgTransitionGap OBJECT-TYPE SYNTAX WmanIf2SsTransitionGap UNITS "us" MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the transition speed SSTTG for TDD and H-FDD SSs allowed by the BS. The usage is defined by WmanIf2SsTransitionGap." ::= { wmanIf2BsBasicCapabilitiesEntry 16 } wmanIf2BsCapRtgTransitionGap OBJECT-TYPE SYNTAX WmanIf2SsTransitionGap UNITS "us" MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the transition speed SSRTG for TDD and H-FDD SSs allowed by the BS. The usage is defined by WmanIf2SsTransitionGap." ::= { wmanIf2BsBasicCapabilitiesEntry 17 } wmanIf2BsCapabilitiesConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2BsCapabilitiesConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the configuration for basic capabilities of BS. The table is intended to be used to restrict the Capabilities implemented by BS, for example in order to comply with local regulatory requirements. The BS should use the configuration along with the implemented Capabilities (wmanIf2BsBasicCapabilitiesTable) for negotiation of basic capabilities with SS using RNG-RSP, SBC-RSP and REG-RSP messages. The negotiated capabilities are obtained by interSubclause of SS reported capabilities, BS raw capabilities and BS configured capabilities. The objects in the table have read-write access. The rows are created by BS as a copy of wmanIf2BsBasicCapabilitiesTable and can be modified by NMS." ::= { wmanIf2BsCapabilities 4 } wmanIf2BsCapabilitiesConfigEntry OBJECT-TYPE SYNTAX WmanIf2BsCapabilitiesConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each BS sector and is indexed by ifIndex." INDEX { ifIndex } ::= { wmanIf2BsCapabilitiesConfigTable 1 } WmanIf2BsCapabilitiesConfigEntry ::= SEQUENCE { wmanIf2BsCapCfgUplinkCidSupport WmanIf2eNumOfCid, wmanIf2BsCapCfgArqSupport WmanIf2ArqSupportType, wmanIf2BsCapCfgDsxFlowControl WmanIf2MaxDsxFlowType, wmanIf2BsCapCfgMacCrcSupport WmanIf2MacCrcSupport, wmanIf2BsCapCfgMcaFlowControl WmanIf2MaxMcaFlowType, wmanIf2BsCapCfgMcpGroupCidSupport WmanIf2MaxMcpGroupCid, wmanIf2BsCapCfgPkmFlowControl WmanIf2MaxPkmFlowType, wmanIf2BsCapCfgAuthPolicyControl WmanIf2AuthPolicyType, wmanIf2BsCapCfgMaxNumOfSupportedSA WmanIf2MaxNumOfSaType, wmanIf2BsCapCfgIpVersion WmanIf2IpVersionType, wmanIf2BsCapCfgMacCsSupportBitMap WmanIf2MacCsBitMap, wmanIf2BsCapCfgMaxNumOfClassifier WmanIf2MaxClassifiers, wmanIf2BsCapCfgPhsSupport WmanIf2PhsSupportType, wmanIf2BsCapCfgBandwidthAllocSupport WmanIf2BwAllocSupport, wmanIf2BsCapCfgPduConstruction WmanIf2PduConstruction, wmanIf2BsCapCfgTtgTransitionGap WmanIf2SsTransitionGap, wmanIf2BsCapCfgRtgTransitionGap WmanIf2SsTransitionGap} wmanIf2BsCapCfgUplinkCidSupport OBJECT-TYPE SYNTAX WmanIf2eNumOfCid MAX-ACCESS read-write STATUS current DESCRIPTION "This object shows the configured number of Uplink CIDs the BS can support per SS." ::= { wmanIf2BsCapabilitiesConfigEntry 1 } wmanIf2BsCapCfgArqSupport OBJECT-TYPE SYNTAX WmanIf2ArqSupportType MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether the BS is configured to support ARQ." ::= { wmanIf2BsCapabilitiesConfigEntry 2 } wmanIf2BsCapCfgDsxFlowControl OBJECT-TYPE SYNTAX WmanIf2MaxDsxFlowType MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the configured maximum number of concurrent DSA, DSC, or DSD transactions that BS allows each SS to have outstanding." DEFVAL { 0 } ::= { wmanIf2BsCapabilitiesConfigEntry 3 } wmanIf2BsCapCfgMacCrcSupport OBJECT-TYPE SYNTAX WmanIf2MacCrcSupport MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether BS is configured to support MAC level CRC." DEFVAL { macCrcSupport } ::= { wmanIf2BsCapabilitiesConfigEntry 4 } wmanIf2BsCapCfgMcaFlowControl OBJECT-TYPE SYNTAX WmanIf2MaxMcaFlowType MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the maximum number of concurrent MCA transactions that BS is configured to allow each SS to have." DEFVAL { 0 } ::= { wmanIf2BsCapabilitiesConfigEntry 5 } wmanIf2BsCapCfgMcpGroupCidSupport OBJECT-TYPE SYNTAX WmanIf2MaxMcpGroupCid MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the maximum number of simultaneous Multicast Polling Groups the BS is configured to allow each SS to belong to." DEFVAL { 0 } ::= { wmanIf2BsCapabilitiesConfigEntry 6 } wmanIf2BsCapCfgPkmFlowControl OBJECT-TYPE SYNTAX WmanIf2MaxPkmFlowType MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the maximum number of concurrent PKM transactions that BS is configured to allow each SS to have." DEFVAL { 0 } ::= { wmanIf2BsCapabilitiesConfigEntry 7 } wmanIf2BsCapCfgAuthPolicyControl OBJECT-TYPE SYNTAX WmanIf2AuthPolicyType MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies authorization policy that BS is configured to be capable of. A bit value of 0 = 'not supported', 1 = 'supported'. If this field is omitted, then both SS and BS shall use the IEEE 802.16 security, constituting X.509 digital certificates and the RSA public key encryption algorithm, as authorization policy." ::= { wmanIf2BsCapabilitiesConfigEntry 8 } wmanIf2BsCapCfgMaxNumOfSupportedSA OBJECT-TYPE SYNTAX WmanIf2MaxNumOfSaType MAX-ACCESS read-write STATUS current DESCRIPTION "This field specifies configured maximum number of supported security association per SS." DEFVAL { 1 } ::= { wmanIf2BsCapabilitiesConfigEntry 9 } wmanIf2BsCapCfgIpVersion OBJECT-TYPE SYNTAX WmanIf2IpVersionType MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the configured version of IP that the BS allows each SS to use on the 2nd Management Connection. The value 'undefined' should not be used in this field." ::= { wmanIf2BsCapabilitiesConfigEntry 10 } wmanIf2BsCapCfgMacCsSupportBitMap OBJECT-TYPE SYNTAX WmanIf2MacCsBitMap MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates BS configured set of MAC convergence sublayer support. When a bit is set, it indicates the corresponding CS feature is supported." ::= { wmanIf2BsCapabilitiesConfigEntry 11 } wmanIf2BsCapCfgMaxNumOfClassifier OBJECT-TYPE SYNTAX WmanIf2MaxClassifiers MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the configured maximum number of admitted Classifiers per SS that the BS can support." DEFVAL { 0 } ::= { wmanIf2BsCapabilitiesConfigEntry 12 } wmanIf2BsCapCfgPhsSupport OBJECT-TYPE SYNTAX WmanIf2PhsSupportType MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the configured level of BS support for PHS." DEFVAL { noPhsSupport } ::= { wmanIf2BsCapabilitiesConfigEntry 13 } wmanIf2BsCapCfgBandwidthAllocSupport OBJECT-TYPE SYNTAX WmanIf2BwAllocSupport MAX-ACCESS read-write STATUS current DESCRIPTION "This field indicates configured properties of the BS for bandwidth allocation purposes. The usage is defined by WmanIf2CapBwAllocSupport." ::= { wmanIf2BsCapabilitiesConfigEntry 14 } wmanIf2BsCapCfgPduConstruction OBJECT-TYPE SYNTAX WmanIf2PduConstruction MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies configured capabilities for construction and transmission of MAC PDUs. The usage is defined by WmanIf2PduConstruction." ::= { wmanIf2BsCapabilitiesConfigEntry 15 } wmanIf2BsCapCfgTtgTransitionGap OBJECT-TYPE SYNTAX WmanIf2SsTransitionGap UNITS "us" MAX-ACCESS read-write STATUS current DESCRIPTION "This field indicates the configured transition speed SSTTG for TDD and H-FDD SSs. The usage is defined by WmanIf2SsTransitionGap." ::= { wmanIf2BsCapabilitiesConfigEntry 16 } wmanIf2BsCapCfgRtgTransitionGap OBJECT-TYPE SYNTAX WmanIf2SsTransitionGap UNITS "us" MAX-ACCESS read-write STATUS current DESCRIPTION "This field indicates the configured transition speed SSRTG for TDD and H-FDD SSs. The usage is defined by WmanIf2SsTransitionGap." ::= { wmanIf2BsCapabilitiesConfigEntry 17 } wmanIf2eBsSsReqCapabilitiesTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2eBsSsReqCapabilitiesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table augments wmanIf2BsRegisteredSsTable to include new capabilities as introduced in IEEE 802.16e 2005 standard." ::= { wmanIf2BsCapabilities 5 } wmanIf2eBsSsReqCapabilitiesEntry OBJECT-TYPE SYNTAX WmanIf2eBsSsReqCapabilitiesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each MS that has been registered in the BS. This table augments the table wmanIf2BsRegisteredSsTable." AUGMENTS { wmanIf2BsRegisteredSsEntry } ::= { wmanIf2eBsSsReqCapabilitiesTable 1 } WmanIf2eBsSsReqCapabilitiesEntry ::= SEQUENCE { wmanIf2eBsSsReqCapDownlinkCidSupport WmanIf2eNumOfCid, wmanIf2eBsSsReqCapPackingSupport WmanIf2ePackingSupport, wmanIf2eBsSsReqCapExtendedRtpsSupport WmanIf2eExtRtpsSupport, wmanIf2eBsSsReqCapMaxNumBurstToMs INTEGER, wmanIf2eBsSsReqCapIpAddrAllocMethod WmanIf2eIpAllocMethod, wmanIf2eBsSsReqCapHandoverSupported WmanIf2eHandoverType, wmanIf2eBsSsReqCapHoProcessTimer Unsigned32, wmanIf2eBsSsReqCapIdleModeTimeout Unsigned32, wmanIf2eBsSsReqCapArqAckType WmanIf2eArqAckType, wmanIf2eBsSsReqCapMacHeader WmanIf2eMacHeaderSupp} wmanIf2eBsSsReqCapDownlinkCidSupport OBJECT-TYPE SYNTAX WmanIf2eNumOfCid MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the number of Downlink CIDs the SS can support." ::= { wmanIf2eBsSsReqCapabilitiesEntry 1 } wmanIf2eBsSsReqCapPackingSupport OBJECT-TYPE SYNTAX WmanIf2ePackingSupport MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the availability of MS support for Packing." REFERENCE "Subclause 11.7.8.11 in IEEE Std 802.16e-2005" ::= { wmanIf2eBsSsReqCapabilitiesEntry 2 } wmanIf2eBsSsReqCapExtendedRtpsSupport OBJECT-TYPE SYNTAX WmanIf2eExtRtpsSupport MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the availability of MS support for extended rtPs." REFERENCE "Subclause 11.7.8.12 in IEEE Std 802.16e-2005" ::= { wmanIf2eBsSsReqCapabilitiesEntry 3 } wmanIf2eBsSsReqCapMaxNumBurstToMs OBJECT-TYPE SYNTAX INTEGER (1..16) MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum number of bursts transmitted concurrently to the MS , including all bursts without CID or with CIDs matching the MS's CIDs." REFERENCE "Subclause 11.7.8.13 in IEEE Std 802.16e-2005" ::= { wmanIf2eBsSsReqCapabilitiesEntry 4 } wmanIf2eBsSsReqCapIpAddrAllocMethod OBJECT-TYPE SYNTAX WmanIf2eIpAllocMethod MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the method of allocating IP address for the secondary management connection." REFERENCE "Subclause 11.7.11 in IEEE Std 802.16e-2005" ::= { wmanIf2eBsSsReqCapabilitiesEntry 5 } wmanIf2eBsSsReqCapHandoverSupported OBJECT-TYPE SYNTAX WmanIf2eHandoverType MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates what type(s) of Handover the BS or MS supports." REFERENCE "Subclause 11.7.12 in IEEE Std 802.16e-2005" ::= { wmanIf2eBsSsReqCapabilitiesEntry 6 } wmanIf2eBsSsReqCapHoProcessTimer OBJECT-TYPE SYNTAX Unsigned32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The duration in frames the MS shall wait until receipt of the next unsolicited network re-entry MAC management message as indicated in the HO Process Optimization element of the RNG-RSP message." REFERENCE "Subclause 11.7.13.2 in IEEE Std 802.16e-2005" ::= { wmanIf2eBsSsReqCapabilitiesEntry 7 } wmanIf2eBsSsReqCapIdleModeTimeout OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Max time interval between MS Idle Mode Location Updates." REFERENCE "Subclause 11.7.20.1 in IEEE Std 802.16e-2005" DEFVAL { 4096 } ::= { wmanIf2eBsSsReqCapabilitiesEntry 8 } wmanIf2eBsSsReqCapArqAckType OBJECT-TYPE SYNTAX WmanIf2eArqAckType MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this parameter specifies the ARQ ACK type supported by the MS." REFERENCE "Subclause 11.7.23 in IEEE Std 802.16e-2005" ::= { wmanIf2eBsSsReqCapabilitiesEntry 9 } wmanIf2eBsSsReqCapMacHeader OBJECT-TYPE SYNTAX WmanIf2eMacHeaderSupp MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether or not the MS and BS support various types of MAC header and extended subheaders." REFERENCE "Subclause 11.7.25 in IEEE Std 802.16e-2005" ::= { wmanIf2eBsSsReqCapabilitiesEntry 10 } wmanIf2eBsSsRspCapabilitiesTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2eBsSsRspCapabilitiesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the basic capability information of SSs that have been negotiated and agreed between BS and SS via RNG-REQ/RSP, SBC-REQ/RSP and REG-REQ/RSP messages. This table augments the wmanIf2BsRegisteredSsTable." REFERENCE "Subclause 6.3.2.3.7 in IEEE Std 802.16-2004" ::= { wmanIf2BsCapabilities 6 } wmanIf2eBsSsRspCapabilitiesEntry OBJECT-TYPE SYNTAX WmanIf2eBsSsRspCapabilitiesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each SS that has been registered in the BS. This table augments the wmanIf2BsRegisteredSsTable. " AUGMENTS { wmanIf2BsRegisteredSsEntry } ::= { wmanIf2eBsSsRspCapabilitiesTable 1 } WmanIf2eBsSsRspCapabilitiesEntry ::= SEQUENCE { wmanIf2eBsSsRspCapDownlinkCidSupport WmanIf2eNumOfCid, wmanIf2eBsSsRspCapPackingSupport WmanIf2ePackingSupport, wmanIf2eBsSsRspCapExtendedRtpsSupport WmanIf2eExtRtpsSupport, wmanIf2eBsSsRspCapMaxNumBurstToMs INTEGER, wmanIf2eBsSsRspCapIpAddrAllocMethod WmanIf2eIpAllocMethod, wmanIf2eBsSsRspCapHandoverSupported WmanIf2eHandoverType, wmanIf2eBsSsRspCapHoProcessTimer Unsigned32, wmanIf2eBsSsRspCapIdleModeTimeout Unsigned32, wmanIf2eBsSsRspCapArqAckType WmanIf2eArqAckType, wmanIf2eBsSsRspCapMacHeader WmanIf2eMacHeaderSupp} wmanIf2eBsSsRspCapDownlinkCidSupport OBJECT-TYPE SYNTAX WmanIf2eNumOfCid MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the number of Downlink CIDs the SS can support." ::= { wmanIf2eBsSsRspCapabilitiesEntry 1 } wmanIf2eBsSsRspCapPackingSupport OBJECT-TYPE SYNTAX WmanIf2ePackingSupport MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the availability of MS support for Packing." REFERENCE "Subclause 11.7.8.11 in IEEE Std 802.16e-2005" ::= { wmanIf2eBsSsRspCapabilitiesEntry 2 } wmanIf2eBsSsRspCapExtendedRtpsSupport OBJECT-TYPE SYNTAX WmanIf2eExtRtpsSupport MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the availability of MS support for extended rtPs." REFERENCE "Subclause 11.7.8.12 in IEEE Std 802.16e-2005" ::= { wmanIf2eBsSsRspCapabilitiesEntry 3 } wmanIf2eBsSsRspCapMaxNumBurstToMs OBJECT-TYPE SYNTAX INTEGER (1..16) MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum number of bursts transmitted concurrently to the MS , including all bursts without CID or with CIDs matching the MS CIDs." REFERENCE "Subclause 11.7.8.13 in IEEE Std 802.16e-2005" ::= { wmanIf2eBsSsRspCapabilitiesEntry 4 } wmanIf2eBsSsRspCapIpAddrAllocMethod OBJECT-TYPE SYNTAX WmanIf2eIpAllocMethod MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the method of allocating IP address for the secondary management connection." REFERENCE "Subclause 11.7.11 in IEEE Std 802.16e-2005" ::= { wmanIf2eBsSsRspCapabilitiesEntry 5 } wmanIf2eBsSsRspCapHandoverSupported OBJECT-TYPE SYNTAX WmanIf2eHandoverType MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates what type(s) of Handover the BS or MS supports." REFERENCE "Subclause 11.7.12 in IEEE Std 802.16e-2005" ::= { wmanIf2eBsSsRspCapabilitiesEntry 6 } wmanIf2eBsSsRspCapHoProcessTimer OBJECT-TYPE SYNTAX Unsigned32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The duration in frames the MS shall wait until receipt of the next unsolicited network re-entry MAC management message as indicated in the HO Process Optimization element of the RNG-RSP message." REFERENCE "Subclause 11.7.13.2 in IEEE Std 802.16e-2005" ::= { wmanIf2eBsSsRspCapabilitiesEntry 7 } wmanIf2eBsSsRspCapIdleModeTimeout OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Max time interval between MS Idle Mode Location Updates." REFERENCE "Subclause 11.7.20.1 in IEEE Std 802.16e-2005" DEFVAL { 4096 } ::= { wmanIf2eBsSsRspCapabilitiesEntry 8 } wmanIf2eBsSsRspCapArqAckType OBJECT-TYPE SYNTAX WmanIf2eArqAckType MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this parameter specifies the ARQ ACK type supported by the MS." REFERENCE "Subclause 11.7.23 in IEEE Std 802.16e-2005" ::= { wmanIf2eBsSsRspCapabilitiesEntry 9 } wmanIf2eBsSsRspCapMacHeader OBJECT-TYPE SYNTAX WmanIf2eMacHeaderSupp MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether or not the MS and BS support various types of MAC header and extended subheaders." REFERENCE "Subclause 11.7.25 in IEEE Std 802.16e-2005" ::= { wmanIf2eBsSsRspCapabilitiesEntry 10 } wmanIf2eBsBasicCapabilitiesTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2eBsBasicCapabilitiesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the basic capabilities of the BS as implemented in BS hardware and software. These capabilities along with the configuration for them (wmanIf2eBsCapabilitiesConfigTable) are used for negotiation of basic capabilities with SS using RNG-RSP, SBC-RSP and REG-RSP messages. The negotiated capabilities are obtained by interSubclause of SS raw reported capabilities, BS raw capabilities and BS configured capabilities. The objects in the table have read-only access. The table is maintained by BS." ::= { wmanIf2BsCapabilities 7 } wmanIf2eBsBasicCapabilitiesEntry OBJECT-TYPE SYNTAX WmanIf2eBsBasicCapabilitiesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each BS sector and is indexed by ifIndex." INDEX { ifIndex } ::= { wmanIf2eBsBasicCapabilitiesTable 1 } WmanIf2eBsBasicCapabilitiesEntry ::= SEQUENCE { wmanIf2eBsCapDownlinkCidSupport WmanIf2eNumOfCid, wmanIf2eBsCapPackingSupport WmanIf2ePackingSupport, wmanIf2eBsCapExtendedRtpsSupport WmanIf2eExtRtpsSupport, wmanIf2eBsCapMaxNumBurstToMs INTEGER, wmanIf2eBsCapIpAddrAllocMethod WmanIf2eIpAllocMethod, wmanIf2eBsCapHandoverSupported WmanIf2eHandoverType, wmanIf2eBsCapHoProcessTimer Unsigned32, wmanIf2eBsCapIdleModeTimeout Unsigned32, wmanIf2eBsCapArqAckType WmanIf2eArqAckType, wmanIf2eBsCapMacHeader WmanIf2eMacHeaderSupp} wmanIf2eBsCapDownlinkCidSupport OBJECT-TYPE SYNTAX WmanIf2eNumOfCid MAX-ACCESS read-only STATUS current DESCRIPTION "This object shows the number of Downlink CIDs the SS can support." ::= { wmanIf2eBsBasicCapabilitiesEntry 1 } wmanIf2eBsCapPackingSupport OBJECT-TYPE SYNTAX WmanIf2ePackingSupport MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the availability of MS support for Packing." REFERENCE "Subclause 11.7.8.11 in IEEE Std 802.16e-2005" ::= { wmanIf2eBsBasicCapabilitiesEntry 2 } wmanIf2eBsCapExtendedRtpsSupport OBJECT-TYPE SYNTAX WmanIf2eExtRtpsSupport MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the availability of MS support for extended rtPs." REFERENCE "Subclause 11.7.8.12 in IEEE Std 802.16e-2005" ::= { wmanIf2eBsBasicCapabilitiesEntry 3 } wmanIf2eBsCapMaxNumBurstToMs OBJECT-TYPE SYNTAX INTEGER (1..16) MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum number of bursts transmitted concurrently to the MS , including all bursts without CID or with CIDs matching the MS CIDs." REFERENCE "Subclause 11.7.8.13 in IEEE Std 802.16e-2005" ::= { wmanIf2eBsBasicCapabilitiesEntry 4 } wmanIf2eBsCapIpAddrAllocMethod OBJECT-TYPE SYNTAX WmanIf2eIpAllocMethod MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the method of allocating IP address for the secondary management connection." REFERENCE "Subclause 11.7.11 in IEEE Std 802.16e-2005" ::= { wmanIf2eBsBasicCapabilitiesEntry 5 } wmanIf2eBsCapHandoverSupported OBJECT-TYPE SYNTAX WmanIf2eHandoverType MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates what type(s) of Handover the BS or MS supports." REFERENCE "Subclause 11.7.12 in IEEE Std 802.16e-2005" ::= { wmanIf2eBsBasicCapabilitiesEntry 6 } wmanIf2eBsCapHoProcessTimer OBJECT-TYPE SYNTAX Unsigned32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The duration in frames the MS shall wait until receipt of the next unsolicited network re-entry MAC management message as indicated in the HO Process Optimization element of the RNG-RSP message." REFERENCE "Subclause 11.7.13.2 in IEEE Std 802.16e-2005" ::= { wmanIf2eBsBasicCapabilitiesEntry 7 } wmanIf2eBsCapIdleModeTimeout OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Max time interval between MS Idle Mode Location Updates." REFERENCE "Subclause 11.7.20.1 in IEEE Std 802.16e-2005" DEFVAL { 4096 } ::= { wmanIf2eBsBasicCapabilitiesEntry 8 } wmanIf2eBsCapArqAckType OBJECT-TYPE SYNTAX WmanIf2eArqAckType MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this parameter specifies the ARQ ACK type supported by the MS." REFERENCE "Subclause 11.7.23 in IEEE Std 802.16e-2005" ::= { wmanIf2eBsBasicCapabilitiesEntry 9 } wmanIf2eBsCapMacHeader OBJECT-TYPE SYNTAX WmanIf2eMacHeaderSupp MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether or not the MS and BS support various types of MAC header and extended subheaders." REFERENCE "Subclause 11.7.25 in IEEE Std 802.16e-2005" ::= { wmanIf2eBsBasicCapabilitiesEntry 10 } wmanIf2eBsCapabilitiesConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2eBsCapabilitiesConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the configuration for basic capabilities of BS. The table is intended to be used to restrict the Capabilities implemented by BS, for example in order to comply with local regulatory requirements. The BS should use the configuration along with the implemented Capabilities (wmanIf2eBsBasicCapabilitiesTable) for negotiation of basic capabilities with SS using RNG-RSP, SBC-RSP and REG-RSP messages. The negotiated capabilities are obtained by interSubclause of SS reported capabilities, BS raw capabilities and BS configured capabilities. The objects in the table have read-write access. The rows are created by BS as a copy of wmanIf2eBsBasicCapabilitiesTable and can be modified by NMS." ::= { wmanIf2BsCapabilities 8 } wmanIf2eBsCapabilitiesConfigEntry OBJECT-TYPE SYNTAX WmanIf2eBsCapabilitiesConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each BS sector and is indexed by ifIndex." INDEX { ifIndex } ::= { wmanIf2eBsCapabilitiesConfigTable 1 } WmanIf2eBsCapabilitiesConfigEntry ::= SEQUENCE { wmanIf2eBsCapCfgDownlinkCidSupport WmanIf2eNumOfCid, wmanIf2eBsCapCfgPackingSupport WmanIf2ePackingSupport, wmanIf2eBsCapCfgExtendedRtpsSupport WmanIf2eExtRtpsSupport, wmanIf2eBsCapCfgMaxNumBurstToMs INTEGER, wmanIf2eBsCapCfgIpAddrAllocMethod WmanIf2eIpAllocMethod, wmanIf2eBsCapCfgHandoverSupported WmanIf2eHandoverType, wmanIf2eBsCapCfgHoProcessTimer Unsigned32, wmanIf2eBsCapCfgIdleModeTimeout Unsigned32, wmanIf2eBsCapCfgArqAckType WmanIf2eArqAckType, wmanIf2eBsCapCfgMacHeader WmanIf2eMacHeaderSupp} wmanIf2eBsCapCfgDownlinkCidSupport OBJECT-TYPE SYNTAX WmanIf2eNumOfCid MAX-ACCESS read-write STATUS current DESCRIPTION "This object shows the number of Downlink CIDs the SS can support." ::= { wmanIf2eBsCapabilitiesConfigEntry 1 } wmanIf2eBsCapCfgPackingSupport OBJECT-TYPE SYNTAX WmanIf2ePackingSupport MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the availability of MS support for Packing." REFERENCE "Subclause 11.7.8.11 in IEEE Std 802.16e-2005" ::= { wmanIf2eBsCapabilitiesConfigEntry 2 } wmanIf2eBsCapCfgExtendedRtpsSupport OBJECT-TYPE SYNTAX WmanIf2eExtRtpsSupport MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates the availability of MS support for extended rtPs." REFERENCE "Subclause 11.7.8.12 in IEEE Std 802.16e-2005" ::= { wmanIf2eBsCapabilitiesConfigEntry 3 } wmanIf2eBsCapCfgMaxNumBurstToMs OBJECT-TYPE SYNTAX INTEGER (1..16) MAX-ACCESS read-write STATUS current DESCRIPTION "Maximum number of bursts transmitted concurrently to the MS , including all bursts without CID or with CIDs matching the MS CIDs." REFERENCE "Subclause 11.7.8.13 in IEEE Std 802.16e-2005" ::= { wmanIf2eBsCapabilitiesConfigEntry 4 } wmanIf2eBsCapCfgIpAddrAllocMethod OBJECT-TYPE SYNTAX WmanIf2eIpAllocMethod MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates the method of allocating IP address for the secondary management connection." REFERENCE "Subclause 11.7.11 in IEEE Std 802.16e-2005" ::= { wmanIf2eBsCapabilitiesConfigEntry 5 } wmanIf2eBsCapCfgHandoverSupported OBJECT-TYPE SYNTAX WmanIf2eHandoverType MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates what type(s) of Handover the BS or MS supports." REFERENCE "Subclause 11.7.12 in IEEE Std 802.16e-2005" ::= { wmanIf2eBsCapabilitiesConfigEntry 6 } wmanIf2eBsCapCfgHoProcessTimer OBJECT-TYPE SYNTAX Unsigned32 UNITS "frames" MAX-ACCESS read-write STATUS current DESCRIPTION "The duration in frames the MS shall wait until receipt of the next unsolicited network re-entry MAC management message as indicated in the HO Process Optimization element of the RNG-RSP message." REFERENCE "Subclause 11.7.13.2 in IEEE Std 802.16e-2005" ::= { wmanIf2eBsCapabilitiesConfigEntry 7 } wmanIf2eBsCapCfgIdleModeTimeout OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Max time interval between MS Idle Mode Location Updates." REFERENCE "Subclause 11.7.20.1 in IEEE Std 802.16e-2005" DEFVAL { 4096 } ::= { wmanIf2eBsCapabilitiesConfigEntry 8 } wmanIf2eBsCapCfgArqAckType OBJECT-TYPE SYNTAX WmanIf2eArqAckType MAX-ACCESS read-write STATUS current DESCRIPTION "The value of this parameter specifies the ARQ ACK type supported by the MS." REFERENCE "Subclause 11.7.23 in IEEE Std 802.16e-2005" ::= { wmanIf2eBsCapabilitiesConfigEntry 9 } wmanIf2eBsCapCfgMacHeader OBJECT-TYPE SYNTAX WmanIf2eMacHeaderSupp MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates whether or not the MS and BS support various types of MAC header and extended subheaders." REFERENCE "Subclause 11.7.25 in IEEE Std 802.16e-2005" ::= { wmanIf2eBsCapabilitiesConfigEntry 10 } wmanIf2BsSsActionsTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2BsSsActionsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains all the actions specified for SSs in the standard. The actions are routed down to SS using unsolicited MAC messages: REG-RSP, DREG-REQ and RES-CMD. The table also contains the parameters of the actions in cases where they are specified by the standard." ::= { wmanIf2BsCps 5 } wmanIf2BsSsActionsEntry OBJECT-TYPE SYNTAX WmanIf2BsSsActionsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is indexed by wmanIf2BsSsActionsMacAddress. The action can be requested for SS in any state not only those registered. However BS will decide whether the action is applicable to the SS based on its current state and execute it or skip it as defined in each action definition." INDEX { wmanIf2BsSsActionsMacAddress } ::= { wmanIf2BsSsActionsTable 1 } WmanIf2BsSsActionsEntry ::= SEQUENCE { wmanIf2BsSsActionsMacAddress MacAddress, wmanIf2BsSsActionsResetSs INTEGER, wmanIf2BsSsActionsAbortSs INTEGER, wmanIf2BsSsActionsOverrideDnFreq Unsigned32, wmanIf2BsSsActionsOverrideChannelId INTEGER, wmanIf2BsSsActionsDeReRegSs INTEGER, wmanIf2BsSsActionsDeReRegSsCode INTEGER, wmanIf2BsSsActionsRowStatus RowStatus} wmanIf2BsSsActionsMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object uniquely identifies the SS as an action target." ::= { wmanIf2BsSsActionsEntry 1 } wmanIf2BsSsActionsResetSs OBJECT-TYPE SYNTAX INTEGER {actionsResetSsNoAction(0), actionsResetSs(1)} MAX-ACCESS read-create STATUS current DESCRIPTION "This object should be implemented as follows: - When set to actionsResetSs value, instructs BS to send RES-CMD to SS - When set to value different than actionsResetSs it should be ignored - When read it should return actionsResetSsNoAction The RES-CMD message shall be transmitted by the BS on an SS Basic CID to force the SS to reset itself, reinitialize its MAC, and repeat initial system access." REFERENCE "Subclause 6.3.2.3.22 in IEEE Std 802.16-2004" ::= { wmanIf2BsSsActionsEntry 2 } wmanIf2BsSsActionsAbortSs OBJECT-TYPE SYNTAX INTEGER {actionsAbortSsNoAction(0), actionsAbortSs(1), actionAbortSsParams(2)} MAX-ACCESS read-create STATUS current DESCRIPTION "This object should be implemented as follows: - When set to actionsAbortSs value, it instructs BS to send unsolicited RNG-RSP with Ranging Status equal to 'abort' without override parameters - When set to actionAbortSsParams value, it instructs BS to send unsolicited RNG-RSP with Ranging Status equal to 'abort' and with 'Downlink Frequency Override' and 'Uplink Channel ID Override' parameters. - When set to any other value it should be ignored - When read it should returned actionsAbortSsNoAction" REFERENCE "Subclause 11.6, Table 365 in IEEE Std 802.16-2004" ::= { wmanIf2BsSsActionsEntry 3 } wmanIf2BsSsActionsOverrideDnFreq OBJECT-TYPE SYNTAX Unsigned32 UNITS "kHz" MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used as a parmeter of the AbortSs action with the code actionAbortSsParams. It is used for licensed bands only. It defines the Center frequency, in kHz, of new downlink channel where the SS should redo initial ranging." REFERENCE "Subclause 11.6, Table 365 in IEEE Std 802.16-2004" ::= { wmanIf2BsSsActionsEntry 4 } wmanIf2BsSsActionsOverrideChannelId OBJECT-TYPE SYNTAX INTEGER (0..199) MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used as a parmeter of the AbortSs action with the code actionAbortSsParams. It is coded as follows: - Licensed bands: The identifier of the uplink channel with which the SS is to redo initial ranging (not used with PHYs without channelized uplinks). - License-exempt bands: The Channel Nr (see 8.5.1) where the SS should redo initial ranging." REFERENCE "Subclause 11.6, Table 365 in IEEE Std 802.16-2004" ::= { wmanIf2BsSsActionsEntry 5 } wmanIf2BsSsActionsDeReRegSs OBJECT-TYPE SYNTAX INTEGER {actionsDeReRegSsNoAction(0), actionsDeReRegSs(1)} MAX-ACCESS read-create STATUS current DESCRIPTION "This object should be implemented as follows: - When set to actionsDeReRegSs value, instructs BS to send DREG-CMD to SS with specified action code - When set to value different than actionsDeReRegSs it should be ignored - When read it should return actionsDeReRegSsNoAction The DREG-CMD message shall be transmitted by the BS on an SS Basic CID to force the SS to change its access state. Upon receiving a DREG-CMD, the SS shall take the action indicated by the action code defined by wmanIf2BsSsActionsDeReRegSsCode." REFERENCE "Subclause 6.3.2.3.26 in IEEE Std 802.16-2004" ::= { wmanIf2BsSsActionsEntry 6 } wmanIf2BsSsActionsDeReRegSsCode OBJECT-TYPE SYNTAX INTEGER {actionsDeReRegSsCodeChangeChan(0), actionsDeReRegSsCodeNoTransmit(1), actionsDeReRegSsCodeLtdTransmit(2), actionsDeReRegSsCodeResume(3)} MAX-ACCESS read-create STATUS current DESCRIPTION "This object defines the action code for wmanIf2BsSsActionsDeReRegSs action. The codes are defined as follows: actionsDeReRegSsCodeChangeChan - SS shall leave the current channel and attempt to access another channel. actionsDeReRegSsCodeNoTransmit - SS shall listen to the current channel but shall not transmit until an RES-CMD message or DREG_CMD with an Action Code that allows transmission is received. actionsDeReRegSsCodeLtdTransmit - SS shall listen to the current channel but only transmit on the Basic, Primary Management and 2nd Management Connections. actionsDeReRegSsCodeResume - SS shall return to normal operation and may transmit on any of its active connections." REFERENCE "Subclause 6.3.2.3.26, Table 55 in IEEE Std 802.16-2004" ::= { wmanIf2BsSsActionsEntry 7 } wmanIf2BsSsActionsRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to ensure that the write operation to multiple columns is guaranteed to be treated as atomic operation by agent." ::= { wmanIf2BsSsActionsEntry 8 } -- -- wmanIf2BsSsPowerSavingStatusTable contains the power saving status -- wmanIf2BsSsPowerSavingStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2BsSsPowerSavingStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the power saving status for each CID in an MS. When the BS roams to a different BS, all entries associated with such MS will be deleted." ::= { wmanIf2BsCps 6 } wmanIf2BsSsPowerSavingStatusEntry OBJECT-TYPE SYNTAX WmanIf2BsSsPowerSavingStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each CID in an MS, and is indexed by ifIndex, wmanIf2BsSsMacAddress, and wmanIf2BsSsCid." INDEX { ifIndex, wmanIf2BsSsMacAddress, wmanIf2BsSsCid } ::= { wmanIf2BsSsPowerSavingStatusTable 1 } WmanIf2BsSsPowerSavingStatusEntry::= SEQUENCE { wmanIf2BsSsCid WmanIf2CidType, wmanIf2BsSsPowerSavingClassId WmanIf2PsClassId} wmanIf2BsSsCid OBJECT-TYPE SYNTAX WmanIf2CidType MAX-ACCESS read-only STATUS current DESCRIPTION "A 16 bit channel identifier to identify a connection." ::= { wmanIf2BsSsPowerSavingStatusEntry 1 } wmanIf2BsSsPowerSavingClassId OBJECT-TYPE SYNTAX WmanIf2PsClassId MAX-ACCESS read-only STATUS current DESCRIPTION "wmanIf2BsSsPowerSavingClassId identifies the power saving class associated with this CID. It maps to an entry in wmanIf2BsSsPowerSavingClassesTable." ::= { wmanIf2BsSsPowerSavingStatusEntry 2 } -- -- wmanIf2BsSsPowerSavingClassesTable contains the power saving classes -- information -- wmanIf2BsSsPowerSavingClassesTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2BsSsPowerSavingClassesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the power saving classes definitions, and activation / deactivation information that are provided by MOB_SLP-REQ and MOB_SLP-RSP messages. When the BS roams to a different BS, all entries associated with such MS will be deleted." ::= { wmanIf2BsCps 7 } wmanIf2BsSsPowerSavingClassesEntry OBJECT-TYPE SYNTAX WmanIf2BsSsPowerSavingClassesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is indexed by ifIndex, wmanIf2BsSsMacAddress, and wmanIf2BsSsPsClassesId. It is intended to support both unicast and multicast service flows. wmanIf2BsSsMacAddress contains the MAC address of the MS to which the power saving classes are associated." INDEX { ifIndex, wmanIf2BsSsMacAddress, wmanIf2BsSsPsClassId } ::= { wmanIf2BsSsPowerSavingClassesTable 1 } WmanIf2BsSsPowerSavingClassesEntry ::= SEQUENCE { wmanIf2BsSsPsClassId WmanIf2PsClassId, wmanIf2BsSsStartFrameNumber INTEGER, wmanIf2BsSsPowerSavingClassType WmanIf2ePsClassType, wmanIf2BsSsPsClassCidDirection WmanIf2ePsClassCidDir, wmanIf2BsSsTrafficTriggeredWakening INTEGER, wmanIf2BsSsInitialSleepWindow INTEGER, wmanIf2BsSsFinalSleepWindowBase INTEGER, wmanIf2BsSsFinalSleepWindowExponent INTEGER, wmanIf2BsSsListeningWindow INTEGER, wmanIf2BsSsPowerSavingMode WmanIf2PowerSavingMode, wmanIf2BsSsSlpId INTEGER} wmanIf2BsSsPsClassId OBJECT-TYPE SYNTAX WmanIf2PsClassId MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object uniquely identifies the power saving classes in a MS." ::= { wmanIf2BsSsPowerSavingClassesEntry 1 } wmanIf2BsSsStartFrameNumber OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Start frame number for first sleep window." REFERENCE "Subclause 6.3.2.3.44 in IEEE Std 802.16e-2005" ::= { wmanIf2BsSsPowerSavingClassesEntry 2 } wmanIf2BsSsPowerSavingClassType OBJECT-TYPE SYNTAX WmanIf2ePsClassType MAX-ACCESS read-write STATUS current DESCRIPTION "Power saving classes type I - BE & NRT-VR, Power saving classes type II - UGS & RT-VR, Power saving classes type III - multicast, management CID" REFERENCE "Subclause 6.3.21.2-4, in IEEE Std 802.16e-2005" ::= { wmanIf2BsSsPowerSavingClassesEntry 3 } wmanIf2BsSsPsClassCidDirection OBJECT-TYPE SYNTAX WmanIf2ePsClassCidDir MAX-ACCESS read-write STATUS current DESCRIPTION "The direction of power saving class's CIDs." REFERENCE "Subclause 6.3.2.3.44, in IEEE Std 802.16e-2005" ::= { wmanIf2BsSsPowerSavingClassesEntry 4 } wmanIf2BsSsTrafficTriggeredWakening OBJECT-TYPE SYNTAX INTEGER (0..1) MAX-ACCESS read-write STATUS current DESCRIPTION "0 = Power Saving Class shall not be deactivated if traffic appears at the connection as per 6.3.19.2. 1 = Power Saving Class shall be deactivated if traffic appears at the connection as 6.3.19.2." REFERENCE "Subclause 6.3.19.2, in IEEE Std 802.16e-2005" ::= { wmanIf2BsSsPowerSavingClassesEntry 5 } wmanIf2BsSsInitialSleepWindow OBJECT-TYPE SYNTAX INTEGER (0..255) UNITS "frame" MAX-ACCESS read-write STATUS current DESCRIPTION "The initial duration for the sleep window. It is not relevant for Power Saving Class type III, and shall return '0'." REFERENCE "Subclause 6.3.2.3.44, in IEEE Std 802.16e-2005" ::= { wmanIf2BsSsPowerSavingClassesEntry 6 } wmanIf2BsSsFinalSleepWindowBase OBJECT-TYPE SYNTAX INTEGER (0..1023) UNITS "frame" MAX-ACCESS read-write STATUS current DESCRIPTION "The final value for the sleep interval. It is not relevant for Power Saving Class type II, and shall return '0'. For Power Saving Class type III, it is the base for duration of single sleep window request." REFERENCE "Subclause 6.3.2.3.44, in IEEE Std 802.16e-2005" ::= { wmanIf2BsSsPowerSavingClassesEntry 7 } wmanIf2BsSsFinalSleepWindowExponent OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "The factor by which the final-sleep window base is multiplied in order to calculate the final-sleep window. The following formula is used: final-sleep window = final-sleep window base x 2^(final-sleep window exponent) For Power Saving Class type III, it is the exponent for the duration of single sleep window request." REFERENCE "Subclause 6.3.2.3.44, in IEEE Std 802.16e-2005" ::= { wmanIf2BsSsPowerSavingClassesEntry 8 } wmanIf2BsSsListeningWindow OBJECT-TYPE SYNTAX INTEGER (0..255) UNITS "frame" MAX-ACCESS read-write STATUS current DESCRIPTION "The Duration of MS listening window. It is not relevant for Power Saving Class type III, and shall return '0'." REFERENCE "Subclause 6.3.2.3.44, in IEEE Std 802.16e-2005" ::= { wmanIf2BsSsPowerSavingClassesEntry 9 } wmanIf2BsSsPowerSavingMode OBJECT-TYPE SYNTAX WmanIf2PowerSavingMode MAX-ACCESS read-write STATUS current DESCRIPTION "Indicate whether the power saving class mode of such CID is active or not. wmanIf2BsSsPowerSavingMode = Sleep_Approved && Operation." REFERENCE "Subclause 6.3.2.3.45, in IEEE Std 802.16e-2005" ::= { wmanIf2BsSsPowerSavingClassesEntry 10 } wmanIf2BsSsSlpId OBJECT-TYPE SYNTAX INTEGER (0..1023) MAX-ACCESS read-only STATUS current DESCRIPTION "wmanIf2BsSsSlpId is assigned by the BS whenever an MS is instructed to enter sleep mode. This number shall be unique among all MSs that are in sleep mode." REFERENCE "Subclause 6.3.2.3.45, in IEEE Std 802.16e-2005" ::= { wmanIf2BsSsPowerSavingClassesEntry 11 } -- -- Mobile Station Sleep Mode Statistics Table -- wmanIf2BsSsSleepModeStatisticsTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2BsSsSleepModeStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the sleep mode statistic for MS. This table shall be maintained as FIFO to store the sleep mode statistics over a period of time that is subject to implementation. This statistics information can be to monitor, fine tuning, or debugging the power saving performance of each MS. When the statistics entry for an MS reaches the limit, it wraps around to the beginning, and overwrites the oldest entry with the new entry. When the BS roams to a different BS, all entries associated with such MS will be deleted." REFERENCE "6.3.21 in IEEE Std 802.16e-2005" ::= { wmanIf2BsCps 8 } wmanIf2BsSsSleepModeStatisticsEntry OBJECT-TYPE SYNTAX WmanIf2BsSsSleepModeStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in the table contains the event of an MS entering the sleep mode. It is indexed by ifIndex, wmanIf2BsSsMacAddress, and wmanIf2BsSsStatisticsIndex. wmanIf2BsSsStatisticsIndex is the index to sleep mode event entry in the table, and should be increased monotonically, and wraps around when it reaches the implementation specific limit. A time stamp is provided in each entry to indicate when the sleep mode event took place." INDEX { ifIndex, wmanIf2BsSsMacAddress, wmanIf2BsSsCid, wmanIf2BsSsStatisticsIndex } ::= { wmanIf2BsSsSleepModeStatisticsTable 1 } WmanIf2BsSsSleepModeStatisticsEntry ::= SEQUENCE { wmanIf2BsSsStatisticsIndex Unsigned32, wmanIf2BsSsSleepWindowStarted Unsigned32, wmanIf2BsSsListeningWindowStarted Unsigned32, wmanIf2BsSsPendingMsdu INTEGER, wmanIf2BsSsSleepWindowTimeStamp DateAndTime} wmanIf2BsSsStatisticsIndex OBJECT-TYPE SYNTAX Unsigned32 (1 .. 4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "wmanIf2BsSsStatisticsIndex identifies the entry in the table where the latest sleep mode event took place." ::= { wmanIf2BsSsSleepModeStatisticsEntry 1 } wmanIf2BsSsSleepWindowStarted OBJECT-TYPE SYNTAX Unsigned32 (1 .. 166777215) UNITS "frame" MAX-ACCESS read-only STATUS current DESCRIPTION "wmanIf2BsSsSleepWindowStarted identifies when the sleep mode is activated. wmanIf2BsSsSleepWindowStarted = current frame number + Start_frame_number. The frame number is provided in the DL-MAP, and is incremented by 1 MOD 2^24 each frame." ::= { wmanIf2BsSsSleepModeStatisticsEntry 2 } wmanIf2BsSsListeningWindowStarted OBJECT-TYPE SYNTAX Unsigned32 (1 .. 166777215) UNITS "frame" MAX-ACCESS read-only STATUS current DESCRIPTION "wmanIf2BsSsListeningWindowStarted identifies when the sleep mode is deactivated. wmanIf2BsSsListeningWindowStarted = wmanIf2BsSsListeningWindowStarted + sleep window The frame number is provided in the DL-MAP, and is incremented by 1 MOD 2^24 each frame." ::= { wmanIf2BsSsSleepModeStatisticsEntry 3 } wmanIf2BsSsPendingMsdu OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Indicate the number of MAC SDU that are received from the network during the sleep window." ::= { wmanIf2BsSsSleepModeStatisticsEntry 4 } wmanIf2BsSsSleepWindowTimeStamp OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "This is the time when sleep window is started in seconds. The definition of time is as in IETF RFC 868." ::= { wmanIf2BsSsSleepModeStatisticsEntry 5 } -- -- Base station PKM group -- wmanIf2BsPkmObjects contain the Base Station Privacy Sublayer objects -- wmanIf2BsPkmObjects OBJECT IDENTIFIER ::= { wmanIf2BsObjects 3 } -- -- Table wmanIf2BsPkmBaseTable -- wmanIf2BsPkmBaseTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2BsPkmBaseEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the basic PKM attributes of each Base Station wireless interface." ::= { wmanIf2BsPkmObjects 1 } wmanIf2BsPkmBaseEntry OBJECT-TYPE SYNTAX WmanIf2BsPkmBaseEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains objects describing attributes of one BS wireless interface." INDEX { ifIndex } ::= { wmanIf2BsPkmBaseTable 1 } WmanIf2BsPkmBaseEntry ::= SEQUENCE { wmanIf2BsPkmDefaultAuthLifetime Integer32, wmanIf2BsPkmDefaultTekLifetime Integer32, wmanIf2BsPkmDefaultSelfSigManufCertTrust INTEGER, wmanIf2BsPkmCheckCertValidityPeriods TruthValue, wmanIf2BsPkmAuthentInfos Counter32, wmanIf2BsPkmAuthRequests Counter32, wmanIf2BsPkmAuthReplies Counter32, wmanIf2BsPkmAuthRejects Counter32, wmanIf2BsPkmAuthInvalids Counter32, wmanIf2BsPkmAuthGraceTime Integer32, wmanIf2BsPkmTekGraceTime Integer32, wmanIf2BsPkmAuthWaitTimeout Integer32, wmanIf2BsPkmReauthWaitTimeout Integer32, wmanIf2BsPkmOpWaitTimeout Integer32, wmanIf2BsPkmRekeyWaitTimeout Integer32, wmanIf2BsPkmAuthRejectWaitTimeout Integer32} wmanIf2BsPkmDefaultAuthLifetime OBJECT-TYPE SYNTAX Integer32 (86400..6048000) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The value of this object is the default lifetime, in seconds, the BS assigns to a new authorization key." REFERENCE "Table 343 in IEEE Std 802.16-2004" DEFVAL { 604800 } ::= { wmanIf2BsPkmBaseEntry 1 } wmanIf2BsPkmDefaultTekLifetime OBJECT-TYPE SYNTAX Integer32 (1800..604800) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The value of this object is the default lifetime, in seconds, the BS assigns to a new Traffic Encryption Key(TEK)." REFERENCE "Table 343 in IEEE Std 802.16-2004" DEFVAL { 43200 } ::= { wmanIf2BsPkmBaseEntry 2 } wmanIf2BsPkmDefaultSelfSigManufCertTrust OBJECT-TYPE SYNTAX INTEGER {trusted (1), untrusted (2)} MAX-ACCESS read-write STATUS current DESCRIPTION "This object determines the default trust of all (new) self-signed manufacturer certificates obtained after setting the object." ::= { wmanIf2BsPkmBaseEntry 3 } wmanIf2BsPkmCheckCertValidityPeriods OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object to TRUE causes all certificates received thereafter to have their validity periods (and their chain's validity periods) checked against the current time of day. A FALSE setting will cause all certificates received Thereafter to not have their validity periods (nor their chain's validity periods) checked against the current time of day." ::= { wmanIf2BsPkmBaseEntry 4 } wmanIf2BsPkmAuthentInfos OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the BS has received an Authentication Information message from any SS." ::= { wmanIf2BsPkmBaseEntry 5 } wmanIf2BsPkmAuthRequests OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the BS has received an Authorization Request message from any SS" ::= { wmanIf2BsPkmBaseEntry 6 } wmanIf2BsPkmAuthReplies OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the BS has transmitted an Authorization Reply message to any SS." ::= { wmanIf2BsPkmBaseEntry 7 } wmanIf2BsPkmAuthRejects OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the BS has transmitted an Authorization Reject message to any SS." ::= { wmanIf2BsPkmBaseEntry 8 } wmanIf2BsPkmAuthInvalids OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the BS has transmitted an Authorization Invalid message to any SS." ::= { wmanIf2BsPkmBaseEntry 9 } wmanIf2BsPkmAuthGraceTime OBJECT-TYPE SYNTAX Integer32 (300..3024000) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The value of this object is the grace time for an authorization key. A SS is expected to start trying to get a new authorization key beginning AuthGraceTime seconds before the authorization key actually expires." REFERENCE "Table 343 and subclause 11.9.19 in IEEE Std 802.16-2004" DEFVAL { 600 } ::= { wmanIf2BsPkmBaseEntry 10 } wmanIf2BsPkmTekGraceTime OBJECT-TYPE SYNTAX Integer32 (300..3024000) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The value of this object is the grace time for the TEK in seconds. The SS is expected to start trying to acquire a new TEK beginning TEK GraceTime seconds before the expiration of the most recent TEK." REFERENCE "Table 343 and subclause 11.9.19 in IEEE Std 802.16-2004" DEFVAL { 3600 } ::= { wmanIf2BsPkmBaseEntry 11 } wmanIf2BsPkmAuthWaitTimeout OBJECT-TYPE SYNTAX Integer32 (2..30) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The value of this object is the Authorize Wait Timeout." REFERENCE "Table 343 and subclause 11.9.19 in IEEE Std 802.16-2004" DEFVAL { 10 } ::= { wmanIf2BsPkmBaseEntry 12 } wmanIf2BsPkmReauthWaitTimeout OBJECT-TYPE SYNTAX Integer32 (2..30) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The value of this object is the Reauthorize Wait Timeout in seconds." REFERENCE "Table 343 and subclause 11.9.19 in IEEE Std 802.16-2004" DEFVAL { 10 } ::= { wmanIf2BsPkmBaseEntry 13 } wmanIf2BsPkmOpWaitTimeout OBJECT-TYPE SYNTAX Integer32 (1..10) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The value of this object is the Operational Wait Timeout in seconds." REFERENCE "Table 343 and subclause 11.9.19 in IEEE Std 802.16-2004" DEFVAL { 1 } ::= { wmanIf2BsPkmBaseEntry 14 } wmanIf2BsPkmRekeyWaitTimeout OBJECT-TYPE SYNTAX Integer32 (1..10) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The value of this object is the Rekey Wait Timeout in seconds." REFERENCE "Table 343 and subclause 11.9.19 in IEEE Std 802.16-2004" DEFVAL { 1 } ::= { wmanIf2BsPkmBaseEntry 15 } wmanIf2BsPkmAuthRejectWaitTimeout OBJECT-TYPE SYNTAX Integer32 (10..600) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The value of this object is the Authorization Reject Wait Timeout in seconds." REFERENCE "Table 343 and subclause 11.9.19 in IEEE Std 802.16-2004" DEFVAL { 60 } ::= { wmanIf2BsPkmBaseEntry 16 } -- -- Table wmanIf2BsSsPkmAuthTable -- wmanIf2BsSsPkmAuthTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2BsSsPkmAuthEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes PKM attributes related to the authorization for each SS. The BS maintains one Primary Security Association with each Baseline Privacy-enabled SS on each BS wireless interface." ::= { wmanIf2BsPkmObjects 2 } wmanIf2BsSsPkmAuthEntry OBJECT-TYPE SYNTAX WmanIf2BsSsPkmAuthEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The BS MUST create one entry per SS per wireless interface, based on the receipt of an Authorization Request message and MUST not delete the entry before the SS authorization permanently expires." INDEX { ifIndex, wmanIf2BsSsPkmAuthMacAddress } ::= { wmanIf2BsSsPkmAuthTable 1 } WmanIf2BsSsPkmAuthEntry ::= SEQUENCE { wmanIf2BsSsPkmAuthMacAddress MacAddress, wmanIf2BsSsPkmAuthKeySequenceNumber Integer32, wmanIf2BsSsPkmAuthExpiresOld DateAndTime, wmanIf2BsSsPkmAuthExpiresNew DateAndTime, wmanIf2BsSsPkmAuthLifetime Integer32, wmanIf2BsSsPkmAuthReset INTEGER, wmanIf2BsSsPkmAuthInfos Counter64, wmanIf2BsSsPkmAuthRequests Counter64, wmanIf2BsSsPkmAuthReplies Counter64, wmanIf2BsSsPkmAuthRejects Counter64, wmanIf2BsSsPkmAuthInvalids Counter64, wmanIf2BsSsPkmAuthRejectErrorCode INTEGER, wmanIf2BsSsPkmAuthRejectErrorString SnmpAdminString, wmanIf2BsSsPkmAuthInvalidErrorCode INTEGER, wmanIf2BsSsPkmAuthInvalidErrorString SnmpAdminString, wmanIf2BsSsPkmAuthPrimarySAId INTEGER, wmanIf2BsSsPkmAuthValidStatus INTEGER} wmanIf2BsSsPkmAuthMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The value of this object is the physical address of the SS to which the authorization association applies." ::= { wmanIf2BsSsPkmAuthEntry 1 } wmanIf2BsSsPkmAuthKeySequenceNumber OBJECT-TYPE SYNTAX Integer32 (0..15) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the most recent authorization key sequence number for this SS." ::= { wmanIf2BsSsPkmAuthEntry 2 } wmanIf2BsSsPkmAuthExpiresOld OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the actual clock time for expiration of the immediate predecessor of the most recent authorization key for this FSM. If this FSM has only one authorization key, then the value is the time of activation of this FSM." ::= { wmanIf2BsSsPkmAuthEntry 3 } wmanIf2BsSsPkmAuthExpiresNew OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the actual clock time for expiration of the most recent authorization key for this FSM" ::= { wmanIf2BsSsPkmAuthEntry 4 } wmanIf2BsSsPkmAuthLifetime OBJECT-TYPE SYNTAX Integer32 (86400..6048000) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The vaue of this object is the lifetime, in seconds, the BS assigns to an authorization key for this SS." REFERENCE "Table 343 in IEEE Std 802.16-2004" DEFVAL { 604800 } ::= { wmanIf2BsSsPkmAuthEntry 5 } wmanIf2BsSsPkmAuthReset OBJECT-TYPE SYNTAX INTEGER {noResetRequested(1), invalidateAuth(2), sendAuthInvalid(3), invalidateTeks(4)} MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object to invalidateAuth(2) causes the BS to invalidate the current SS authorization key(s), but not to transmit an Authorization Invalid message nor to invalidate unicast TEKs. Setting this object to sendAuthInvalid(3) causes the BS to invalidate the current SS authorization key(s), and to transmit an Authorization Invalid message to the SS, but not to invalidate unicast TEKs. Setting this object to invalidateTeks(4) causes the BS to invalidate the current SS authorization key(s), to transmit an Authorization Invalid message to the SS, and to invalidate all unicast TEKs associated with this SS authorization. Reading this object returns the most-recently-set value of this object, or returns noResetRequested(1) if the object has not been set since the last BS reboot." ::= { wmanIf2BsSsPkmAuthEntry 6 } wmanIf2BsSsPkmAuthInfos OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the BS has received an Authentication Information message from this SS." ::= { wmanIf2BsSsPkmAuthEntry 7 } wmanIf2BsSsPkmAuthRequests OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the BS has received an Authorization Request message from this SS." ::= { wmanIf2BsSsPkmAuthEntry 8 } wmanIf2BsSsPkmAuthReplies OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the BS has transmitted an Authorization Reply message to this SS." ::= { wmanIf2BsSsPkmAuthEntry 9 } wmanIf2BsSsPkmAuthRejects OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the BS has transmitted an Authorization Reject message to this SS." ::= { wmanIf2BsSsPkmAuthEntry 10 } wmanIf2BsSsPkmAuthInvalids OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the BS has transmitted an Authorization Invalid message to this SS." ::= { wmanIf2BsSsPkmAuthEntry 11 } wmanIf2BsSsPkmAuthRejectErrorCode OBJECT-TYPE SYNTAX INTEGER {noInformation(0), unauthorizedSs(1), unauthorizedSaid(2), permanentAuthorizationFailure(6)} MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the enumerated description of the Error-Code in most recent Authorization Reject message transmitted to the SS." REFERENCE "IEEE Std 802.16-2004; Table 371" ::= { wmanIf2BsSsPkmAuthEntry 12 } wmanIf2BsSsPkmAuthRejectErrorString OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the Display-String in most recent Authorization Reject message transmitted to the SS. This is a zero length string if no Authorization Reject message has been transmitted to the SS." ::= { wmanIf2BsSsPkmAuthEntry 13 } wmanIf2BsSsPkmAuthInvalidErrorCode OBJECT-TYPE SYNTAX INTEGER {noInformation(0), unauthorizedSs(1), unsolicited(3), invalidKeySequence(4), keyRequestAuthenticationFailure(5)} MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the enumerated description of the Error-Code in most recent Authorization Invalid message transmitted to the SS." REFERENCE "IEEE Std 802.16-2004; Table 371" ::= { wmanIf2BsSsPkmAuthEntry 14 } wmanIf2BsSsPkmAuthInvalidErrorString OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the Display-String in most recent Authorization Invalid message transmitted to the SS. This is a zero length string if no Authorization Invalid message has been transmitted to the SS." ::= { wmanIf2BsSsPkmAuthEntry 15 } wmanIf2BsSsPkmAuthPrimarySAId OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the Primary Security Association identifier." REFERENCE "IEEE Std 802.16-2004; 11.9.7" ::= { wmanIf2BsSsPkmAuthEntry 16 } wmanIf2BsSsPkmAuthValidStatus OBJECT-TYPE SYNTAX INTEGER {unknown (0), validSsChained (1), validSsTrusted (2), invalidSsUntrusted (3), invalidCAUntrusted (4), invalidSsOther (5), invalidCAOther (6)} MAX-ACCESS read-only STATUS current DESCRIPTION "Contains the reason why a SS's certificate is deemed valid or invalid. Return unknown if the SS is running PKM mode. ValidSsChained means the certificate is valid because it chains to a valid certificate. ValidSsTrusted means the certificate is valid because it has been provisioned to be trusted. InvalidSsUntrusted means the certificate is invalid because it has been provisioned to be untrusted. InvalidCAUntrusted means the certificate is invalid because it chains to an untrusted certificate. InvalidSsOther and InvalidCAOther refer to errors in parsing, validity periods, etc, which are attributable to the SS certificate or its chain respectively." ::= { wmanIf2BsSsPkmAuthEntry 17 } -- -- Table wmanIf2BsPkmTekTable -- wmanIf2BsPkmTekTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2BsPkmTekEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the attributes of each Traffic Encryption Key (TEK) association. The BS maintains one TEK association per SAID on each BS wireless interface." ::= { wmanIf2BsPkmObjects 3 } wmanIf2BsPkmTekEntry OBJECT-TYPE SYNTAX WmanIf2BsPkmTekEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains objects describing attributes of one TEK association on a particular BS wireless interface. The BS MUST create one entry per SAID per wireless interface, based on the receipt of a Key Request message, and MUST not delete the entry before the SS authorization for the SAID permanently expires." INDEX { ifIndex, wmanIf2BsPkmTekSAId } ::= { wmanIf2BsPkmTekTable 1 } WmanIf2BsPkmTekEntry ::= SEQUENCE { wmanIf2BsPkmTekSAId INTEGER, wmanIf2BsPkmTekSAType INTEGER, wmanIf2BsPkmTekDataEncryptAlg WmanIf2DataEncryptAlgId, wmanIf2BsPkmTekDataAuthentAlg WmanIf2DataAuthAlgId, wmanIf2BsPkmTekEncryptAlg WmanIf2TekEncryptAlgId, wmanIf2BsPkmTekLifetime Integer32, wmanIf2BsPkmTekKeySequenceNumber Integer32, wmanIf2BsPkmTekExpiresOld DateAndTime, wmanIf2BsPkmTekExpiresNew DateAndTime, wmanIf2BsPkmTekReset TruthValue, wmanIf2BsPkmKeyRequests Counter32, wmanIf2BsPkmKeyReplies Counter32, wmanIf2BsPkmKeyRejects Counter32, wmanIf2BsPkmTekInvalids Counter32, wmanIf2BsPkmKeyRejectErrorCode INTEGER, wmanIf2BsPkmKeyRejectErrorString SnmpAdminString, wmanIf2BsPkmTekInvalidErrorCode INTEGER, wmanIf2BsPkmTekInvalidErrorString SnmpAdminString} wmanIf2BsPkmTekSAId OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The value of this object is the Security Association ID (SAID)." REFERENCE "IEEE Std 802.16-2004; 11.9.7" ::= { wmanIf2BsPkmTekEntry 1 } wmanIf2BsPkmTekSAType OBJECT-TYPE SYNTAX INTEGER {primarySA(0), staticSA(1), dynamicSA(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the type of security association. Dynamic does not apply to SSs running in PKM mode." REFERENCE "IEEE Std 802.16-2004; subclause 11.9.18" ::= { wmanIf2BsPkmTekEntry 2 } wmanIf2BsPkmTekDataEncryptAlg OBJECT-TYPE SYNTAX WmanIf2DataEncryptAlgId MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the data encryption algorithm being utilized." REFERENCE "Table 375, IEEE Std 802.16-2004" ::= { wmanIf2BsPkmTekEntry 3 } wmanIf2BsPkmTekDataAuthentAlg OBJECT-TYPE SYNTAX WmanIf2DataAuthAlgId MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the data authentication algorithm being utilized." REFERENCE "Table 376, IEEE Std 802.16-2004" ::= { wmanIf2BsPkmTekEntry 4 } wmanIf2BsPkmTekEncryptAlg OBJECT-TYPE SYNTAX WmanIf2TekEncryptAlgId MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the TEK key encryption algorithm being utilized." REFERENCE "Table 377, IEEE Std 802.16-2004" ::= { wmanIf2BsPkmTekEntry 5 } wmanIf2BsPkmTekLifetime OBJECT-TYPE SYNTAX Integer32 (1800..604800) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the lifetime, in seconds, the BS assigns to keys for this TEK association." REFERENCE "Table 343 in IEEE Std 802.16-2004" DEFVAL { 43200 } ::= { wmanIf2BsPkmTekEntry 6 } wmanIf2BsPkmTekKeySequenceNumber OBJECT-TYPE SYNTAX Integer32 (0..3) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the most recent TEK key sequence number for this SAID." REFERENCE "IEEE Std 802.16-2004; subclause 11.9.5" ::= { wmanIf2BsPkmTekEntry 7 } wmanIf2BsPkmTekExpiresOld OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the actual clock time for expiration of the immediate predecessor of the most recent TEK for this FSM. If this FSM has only one TEK, then the value is the time of activation of this FSM." ::= { wmanIf2BsPkmTekEntry 8 } wmanIf2BsPkmTekExpiresNew OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the actual clock time for expiration of the most recent TEK for this FSM." ::= { wmanIf2BsPkmTekEntry 9 } wmanIf2BsPkmTekReset OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object to TRUE causes the BS to invalidate the current active TEK(s) (plural due to key transition periods), and to generate a new TEK for the associated SAID; the BS MAY also generate an unsolicited TEK Invalid message, to optimize the TEK synchronization between the BS and the SS. Reading this object always returns FALSE." ::= { wmanIf2BsPkmTekEntry 10 } wmanIf2BsPkmKeyRequests OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the BS has received a Key Request message." ::= { wmanIf2BsPkmTekEntry 11 } wmanIf2BsPkmKeyReplies OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the BS has transmitted a Key Reply message." ::= { wmanIf2BsPkmTekEntry 12 } wmanIf2BsPkmKeyRejects OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the BS has transmitted a Key Reject message." ::= { wmanIf2BsPkmTekEntry 13 } wmanIf2BsPkmTekInvalids OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the BS has transmitted a TEK Invalid message." ::= { wmanIf2BsPkmTekEntry 14 } wmanIf2BsPkmKeyRejectErrorCode OBJECT-TYPE SYNTAX INTEGER {noInformation(0), unauthorizedSaid(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the enumerated; description of the Error-Code in the most recent Key Reject message sent in response to a Key Request for this SAID." REFERENCE "IEEE Std 802.16-2004; Table 371" ::= { wmanIf2BsPkmTekEntry 15 } wmanIf2BsPkmKeyRejectErrorString OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the Display-String in the most recent Key Reject message sent in response to a Key Request for this SAID. This is a zero length string if no Key Reject message has been received since reboot." ::= { wmanIf2BsPkmTekEntry 16 } wmanIf2BsPkmTekInvalidErrorCode OBJECT-TYPE SYNTAX INTEGER {noInformation(0), invalidKeySequence(4)} MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the enumerated description of the Error-Code in the most recent TEK Invalid message sent in association with this SAID." REFERENCE "IEEE Std 802.16-2004; Table 371" ::= { wmanIf2BsPkmTekEntry 17 } wmanIf2BsPkmTekInvalidErrorString OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the Display-String in the most recent TEK Invalid message sent in association with this SAID. This is a zero length string if no TEK Invalid message has been received since reboot." ::= { wmanIf2BsPkmTekEntry 18 } -- -- Base station Notification Group -- wmanIf2BsNotificationObjects contains the BS SNMP Trap objects -- wmanIf2BsNotification OBJECT IDENTIFIER ::= { wmanIf2BsObjects 4 } wmanIf2BsTrapControl OBJECT IDENTIFIER ::= { wmanIf2BsNotification 1 } wmanIf2BsTrapDefinitions OBJECT IDENTIFIER ::= { wmanIf2BsNotification 2 } -- This object groups all NOTIFICATION-TYPE objects for BS. -- It is defined following RFC2758 sections 8.5 and 8.6 -- for the compatibility with SNMPv1. wmanIf2BsTrapPrefix OBJECT IDENTIFIER ::= { wmanIf2BsTrapDefinitions 0 } wmanIf2BsTrapControlRegister OBJECT-TYPE SYNTAX BITS {wmanIf2BsSsStatusNotification (0), wmanIf2BsSsDynamicServiceFail (1), wmanIf2BsSsRssiStatusChange (2), wmanIf2BsSsRegistrer (3), wmanIf2BsSsPkmFail (4), wmanIf2BsSsDynamicServiceFail2 (5), wmanIf2BsSsRegister2Trap (6)} MAX-ACCESS read-write STATUS current DESCRIPTION "The object is used to enable or disable Base Station traps. From left to right, the set bit indicates the corresponding Base Station trap is enabled." ::= { wmanIf2BsTrapControl 1 } wmanIf2BsStatusTrapControlRegister OBJECT-TYPE SYNTAX BITS {unused(0), ssInitRangingSucc(1), ssInitRangingFail(2), ssRegistered(3), ssRegistrationFail(4), ssDeregistered(5), ssBasicCapabilitySucc(6), ssBasicCapabilityFail(7), ssAuthorizationSucc(8), ssAuthorizationFail(9), tftpSucc(10), tftpFail(11), sfCreationSucc(12), sfCreationFail(13)} MAX-ACCESS read-write STATUS current DESCRIPTION "The object is used to enable or disable Base Station status notification traps. The set bit indicates the corresponding Base Station trap is enabled." ::= { wmanIf2BsTrapControl 2 } -- -- BS threshold Definitions -- wmanIf2BsThresholdConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2BsThresholdConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains threshold objects that can be set to detect the threshold crossing events." ::= { wmanIf2BsTrapControl 3 } wmanIf2BsThresholdConfigEntry OBJECT-TYPE SYNTAX WmanIf2BsThresholdConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each BS sector, and is indexed by ifIndex." INDEX { ifIndex } ::= { wmanIf2BsThresholdConfigTable 1 } WmanIf2BsThresholdConfigEntry ::= SEQUENCE { wmanIf2BsRssiLowThreshold Integer32, wmanIf2BsRssiHighThreshold Integer32} wmanIf2BsRssiLowThreshold OBJECT-TYPE SYNTAX Integer32 UNITS "dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "Low threshold for generating the RSSI alarm." ::= { wmanIf2BsThresholdConfigEntry 1 } wmanIf2BsRssiHighThreshold OBJECT-TYPE SYNTAX Integer32 UNITS "dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "High threshold for clearing the RSSI alarm." ::= { wmanIf2BsThresholdConfigEntry 2 } -- -- Subscriber station Notification Objects Definitions -- wmanIf2BsSsNotificationObjectsTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2BsSsNotificationObjectsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains SS notification objects that have been reported by the trap." ::= { wmanIf2BsTrapDefinitions 1 } wmanIf2BsSsNotificationObjectsEntry OBJECT-TYPE SYNTAX WmanIf2BsSsNotificationObjectsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each SS that has generated traps, and is double indexed by wmanIf2BsSsNotificationMacAddr and ifIndex for BS sector." INDEX { ifIndex, wmanIf2BsSsNotificationMacAddr } ::= { wmanIf2BsSsNotificationObjectsTable 1 } WmanIf2BsSsNotificationObjectsEntry ::= SEQUENCE { wmanIf2BsSsNotificationMacAddr MacAddress, wmanIf2BsSsStatusValue INTEGER, wmanIf2BsSsStatusInfo OCTET STRING, wmanIf2BsDynamicServiceType INTEGER, wmanIf2BsDynamicServiceFailReason OCTET STRING, wmanIf2BsSsRssiStatus INTEGER, wmanIf2BsSsRssiStatusInfo OCTET STRING, wmanIf2BsSsRegisterStatus INTEGER, wmanIf2BsDynamicServiceFailSfid Unsigned32} wmanIf2BsSsNotificationMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address of the SS, reporing the notofiation." ::= { wmanIf2BsSsNotificationObjectsEntry 1 } wmanIf2BsSsStatusValue OBJECT-TYPE SYNTAX INTEGER {ssInitRangingSucc(1), ssInitRangingFail(2), ssRegistered(3), ssRegistrationFail(4), ssDeregistered(5), ssBasicCapabilitySucc(6), ssBasicCapabilityFail(7), ssAuthorizationSucc(8), ssAuthorizationFail(9), tftpSucc(10), tftpFail(11), sfCreationSucc(12), sfCreationFail(13)} MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the status of a SS, as it goes through network entry and initialization procedure." ::= { wmanIf2BsSsNotificationObjectsEntry 2 } wmanIf2BsSsStatusInfo OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the reason of SS's status change." ::= { wmanIf2BsSsNotificationObjectsEntry 3 } wmanIf2BsDynamicServiceType OBJECT-TYPE SYNTAX INTEGER {bsSfCreationReq(1), bsSfCreationRsp(2), bsSfCreationAck(3)} MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the dynamic service flow creation command type." ::= { wmanIf2BsSsNotificationObjectsEntry 4 } wmanIf2BsDynamicServiceFailReason OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the reason why the service flow creation has failed." ::= { wmanIf2BsSsNotificationObjectsEntry 5 } wmanIf2BsSsRssiStatus OBJECT-TYPE SYNTAX INTEGER {bsRssiAlarm(1), bsRssiNoAlarm(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "A RSSI alarm is generated when RSSI becomes lower than wmanIf2BsLowRssiThreshold and is cleared when RSSI becomes higher than wmanIf2BsLowRssiThreshold." ::= { wmanIf2BsSsNotificationObjectsEntry 6 } wmanIf2BsSsRssiStatusInfo OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the reason why RSSI alarm is generated." ::= { wmanIf2BsSsNotificationObjectsEntry 7 } wmanIf2BsSsRegisterStatus OBJECT-TYPE SYNTAX INTEGER {ssRegister(1), ssDeregister(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the status of SS registration." ::= { wmanIf2BsSsNotificationObjectsEntry 8 } wmanIf2BsDynamicServiceFailSfid OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "This object identifies the dynamic service flow for notification purposes." ::= { wmanIf2BsSsNotificationObjectsEntry 9 } -- -- Subscriber station Notification Trap Definitions -- wmanIf2BsSsStatusNotificationTrap NOTIFICATION-TYPE OBJECTS {ifIndex, wmanIf2BsSsNotificationMacAddr, wmanIf2BsSsStatusValue, wmanIf2BsSsStatusInfo} STATUS current DESCRIPTION "This trap reports the status of a SS. Based on this notification the NMS will issue an alarm with certain severity depending on the status and the reason received." ::= { wmanIf2BsTrapPrefix 1 } wmanIf2BsSsDynamicServiceFailTrap NOTIFICATION-TYPE OBJECTS {ifIndex, wmanIf2BsSsNotificationMacAddr, wmanIf2BsDynamicServiceType, wmanIf2BsDynamicServiceFailReason} STATUS deprecated DESCRIPTION "Trap deprecated due to limited value without object reporting SFID of victim service flow. An event to report the failure of a dynamic service operation happened during the dynamic services process and detected in the Bs side." ::= { wmanIf2BsTrapPrefix 2 } wmanIf2BsSsRssiStatusChangeTrap NOTIFICATION-TYPE OBJECTS {ifIndex, wmanIf2BsSsNotificationMacAddr, wmanIf2BsSsRssiStatus, wmanIf2BsSsRssiStatusInfo} STATUS current DESCRIPTION "An event to report that the uplink RSSI is below wmanIf2BsLowRssiThreshold, or above wmanIf2BsHighRssiThreshold after restore." ::= { wmanIf2BsTrapPrefix 3 } wmanIf2BsSsPkmFailTrap NOTIFICATION-TYPE OBJECTS {wmanIf2BsSsNotificationMacAddr} STATUS current DESCRIPTION "An event to report the failure of a Pkm operation." ::= { wmanIf2BsTrapPrefix 4 } wmanIf2BsSsRegistrerTrap NOTIFICATION-TYPE OBJECTS {wmanIf2BsSsNotificationMacAddr, wmanIf2BsSsRegisterStatus} STATUS deprecated DESCRIPTION "Trap deprecated due to limited value without object ifIndex reported. An event to report SS registration status." ::= { wmanIf2BsTrapPrefix 5 } wmanIf2BsSsDynamicServiceFail2Trap NOTIFICATION-TYPE OBJECTS {ifIndex, wmanIf2BsSsNotificationMacAddr, wmanIf2BsDynamicServiceType, wmanIf2BsDynamicServiceFailReason, wmanIf2BsDynamicServiceFailSfid} STATUS current DESCRIPTION "An event reporting failure of DSx operation for a service flow identified by wmanIf2BsDynamicServiceFailSfid and detected in the Bs side." ::= { wmanIf2BsTrapPrefix 6 } wmanIf2BsSsRegister2Trap NOTIFICATION-TYPE OBJECTS {ifIndex, wmanIf2BsSsNotificationMacAddr, wmanIf2BsSsRegisterStatus} STATUS current DESCRIPTION "An event to report SS registration status for a given sector identified by ifIndex." ::= { wmanIf2BsTrapPrefix 7 } -- -- Base station PHY Group -- wmanIf2BsPhy OBJECT IDENTIFIER ::= { wmanIf2BsObjects 6 } -- -- BS OFDM PHY objects -- wmanIf2BsOfdmPhy OBJECT IDENTIFIER ::= { wmanIf2BsPhy 1 } wmanIf2BsOfdmUplinkChannelTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2BsOfdmUplinkChannelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains UCD channel attributes, defining the transmission characteristics of uplink channels" REFERENCE "Table 349 and Table 352, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmPhy 1 } wmanIf2BsOfdmUplinkChannelEntry OBJECT-TYPE SYNTAX WmanIf2BsOfdmUplinkChannelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each uplink channel of multi-sector BS, and is indexed by BS ifIndex. An entry in this table exists for each ifEntry of BS with an ifType of propBWAp2Mp." INDEX { ifIndex } ::= { wmanIf2BsOfdmUplinkChannelTable 1 } WmanIf2BsOfdmUplinkChannelEntry ::= SEQUENCE { wmanIf2BsOfdmCtBasedResvTimeout INTEGER, wmanIf2BsOfdmBwReqOppSize INTEGER, wmanIf2BsOfdmRangReqOppSize INTEGER, wmanIf2BsOfdmUplinkCenterFreq Unsigned32, wmanIf2BsOfdmNumSubChReqRegionFull INTEGER, wmanIf2BsOfdmNumSymbolsReqRegionFull INTEGER, wmanIf2BsOfdmSubChFocusCtCode INTEGER, wmanIf2BsOfdmUpLinkChannelId INTEGER} wmanIf2BsOfdmCtBasedResvTimeout OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-write STATUS current DESCRIPTION "The number of UL-MAPs to receive before contention-based reservation is attempted again for the same connection." REFERENCE "Table 349, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmUplinkChannelEntry 1 } wmanIf2BsOfdmBwReqOppSize OBJECT-TYPE SYNTAX INTEGER (1..65535) UNITS "PS" MAX-ACCESS read-write STATUS current DESCRIPTION "Size (in units of PS) of PHY payload that SS may use to format and transmit a bandwidth request message in a contention request opportunity. The value includes all PHY overhead as well as allowance for the MAC data the message may hold." REFERENCE "Table 349, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmUplinkChannelEntry 2 } wmanIf2BsOfdmRangReqOppSize OBJECT-TYPE SYNTAX INTEGER (1..65535) UNITS "PS" MAX-ACCESS read-write STATUS current DESCRIPTION "Size (in units of PS) of PHY payload that SS may use to format and transmit a RNG-REQ message in a contention request opportunity. The value includes all PHY overhead as well as allowance for the MAC data the message may hold and the maxiumum SS/BS roundtrip propagation delay." REFERENCE "Table 349, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmUplinkChannelEntry 3 } wmanIf2BsOfdmUplinkCenterFreq OBJECT-TYPE SYNTAX Unsigned32 UNITS "kHz" MAX-ACCESS read-write STATUS current DESCRIPTION " Uplink center frequency (kHz)" REFERENCE "Table 349, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmUplinkChannelEntry 4 } wmanIf2BsOfdmNumSubChReqRegionFull OBJECT-TYPE SYNTAX INTEGER {oneSubchannel(0), twoSubchannels(1), fourSubchannels(2), eightSubchannels(3), sixteenSubchannels(4)} MAX-ACCESS read-write STATUS current DESCRIPTION "Number of subchannels used by each transmit opportunity when REQ Region-Full is allocated in subchannelization region." REFERENCE "Table 352, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmUplinkChannelEntry 5 } wmanIf2BsOfdmNumSymbolsReqRegionFull OBJECT-TYPE SYNTAX INTEGER (0..31) MAX-ACCESS read-write STATUS current DESCRIPTION "Number of OFDM symbols used by each transmit opportunity when REQ Region-Full is allocated in subchannelization region." REFERENCE "Table 352, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmUplinkChannelEntry 6 } wmanIf2BsOfdmSubChFocusCtCode OBJECT-TYPE SYNTAX INTEGER (0..8) MAX-ACCESS read-write STATUS current DESCRIPTION "Number of contention codes (CSE) that shall only be used to request a subchannelized allocation. Default value 0. Allowed values 0-8." REFERENCE "Table 352, in IEEE Std 802.16-2004" DEFVAL { 0 } ::= { wmanIf2BsOfdmUplinkChannelEntry 7 } wmanIf2BsOfdmUpLinkChannelId OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "The identifier of the uplink channel to which the relevant RNG-RSP or RNG-REQ message refers." REFERENCE "Subclause 6.3.2.3.4. Table 16, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmUplinkChannelEntry 8 } wmanIf2BsOfdmDownlinkChannelTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2BsOfdmDownlinkChannelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains DCD channel attributes, defining the transmission characteristics of downlink channels" REFERENCE "Table 358, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmPhy 2 } wmanIf2BsOfdmDownlinkChannelEntry OBJECT-TYPE SYNTAX WmanIf2BsOfdmDownlinkChannelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each downlink channel of multi-sector BS, and is indexed by BS ifIndex. An entry in this table exists for each ifEntry of BS with an ifType of propBWAp2Mp." INDEX { ifIndex } ::= { wmanIf2BsOfdmDownlinkChannelTable 1 } WmanIf2BsOfdmDownlinkChannelEntry ::= SEQUENCE { wmanIf2BsOfdmBsEIRP INTEGER, wmanIf2BsOfdmChannelNumber WmanIf2ChannelNumber, wmanIf2BsOfdmTTG INTEGER, wmanIf2BsOfdmRTG INTEGER, wmanIf2BsOfdmInitRngMaxRSS INTEGER, wmanIf2BsOfdmDownlinkCenterFreq Unsigned32, wmanIf2BsOfdmBsId WmanIf2BsIdType, wmanIf2BsOfdmMacVersion WmanIf2MacVersion, wmanIf2BsOfdmFrameDurationCode INTEGER, wmanIf2BsOfdmDownLinkChannelId INTEGER} wmanIf2BsOfdmBsEIRP OBJECT-TYPE SYNTAX INTEGER (-32768..32767) UNITS "dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "The EIRP is the equivalent isotropic radiated power of the base station, which is computed for a simple single-antenna transmitter." REFERENCE "Table 358, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmDownlinkChannelEntry 1 } wmanIf2BsOfdmChannelNumber OBJECT-TYPE SYNTAX WmanIf2ChannelNumber MAX-ACCESS read-write STATUS current DESCRIPTION "Downlink channel number as defined in 8.5. Used for license-exempt operation only." REFERENCE "Table 358, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmDownlinkChannelEntry 2 } wmanIf2BsOfdmTTG OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Transmit / Receive Transition Gap." REFERENCE "Table 358, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmDownlinkChannelEntry 3 } wmanIf2BsOfdmRTG OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Receive / Transmit Transition Gap." REFERENCE "Table 358, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmDownlinkChannelEntry 4 } wmanIf2BsOfdmInitRngMaxRSS OBJECT-TYPE SYNTAX INTEGER (-32768..32767) UNITS "dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "Initial Ranging Max. equivalent isotropic received power at BS Signed in units of 1 dBm." REFERENCE "Table 358, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmDownlinkChannelEntry 5 } wmanIf2BsOfdmDownlinkCenterFreq OBJECT-TYPE SYNTAX Unsigned32 UNITS "kHz" MAX-ACCESS read-write STATUS current DESCRIPTION "Downlink center frequency (kHz)." REFERENCE "Table 358, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmDownlinkChannelEntry 6 } wmanIf2BsOfdmBsId OBJECT-TYPE SYNTAX WmanIf2BsIdType MAX-ACCESS read-write STATUS current DESCRIPTION "Base station ID." REFERENCE "Table 358, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmDownlinkChannelEntry 7 } wmanIf2BsOfdmMacVersion OBJECT-TYPE SYNTAX WmanIf2MacVersion MAX-ACCESS read-write STATUS current DESCRIPTION "This parameter specifies the version of 802.16 to which the message originator conforms." REFERENCE "Table 358, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmDownlinkChannelEntry 8 } wmanIf2BsOfdmFrameDurationCode OBJECT-TYPE SYNTAX INTEGER {duration2dot5ms(0), duration4ms(1), duration5ms(2), duration8ms(3), duration10ms(4), duration12dot5ms(5), duration20ms(6)} MAX-ACCESS read-write STATUS current DESCRIPTION "The duration of the frame. The frame duration code values are specified in Table 230." REFERENCE "Subclause 11.4.1, Table 230, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmDownlinkChannelEntry 9 } wmanIf2BsOfdmDownLinkChannelId OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "The identifier of the downlink channel to which this message refers." REFERENCE "Subclause 6.3.2.3.1. Table 15, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmDownlinkChannelEntry 10 } wmanIf2BsOfdmUcdBurstProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2BsOfdmUcdBurstProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains UCD burst profiles for each uplink channel" REFERENCE "Table 356, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmPhy 3 } wmanIf2BsOfdmUcdBurstProfileEntry OBJECT-TYPE SYNTAX WmanIf2BsOfdmUcdBurstProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each UCD burst profile. This table is double indexed. The primary index is an ifIndex with an ifType of propBWAp2Mp. The secondary index is wmanIf2BsOfdmUiucIndex." INDEX { ifIndex, wmanIf2BsOfdmUiucIndex } ::= { wmanIf2BsOfdmUcdBurstProfileTable 1 } WmanIf2BsOfdmUcdBurstProfileEntry ::= SEQUENCE { wmanIf2BsOfdmUiucIndex INTEGER, wmanIf2BsOfdmUcdFecCodeType WmanIf2OfdmFecCodeType, wmanIf2BsOfdmFocusCtPowerBoost INTEGER, wmanIf2BsOfdmUcdTcsEnable INTEGER, wmanIf2BsOfdmUcdBurstProfileRowStatus RowStatus} wmanIf2BsOfdmUiucIndex OBJECT-TYPE SYNTAX INTEGER (5 .. 12) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Uplink Interval Usage Code indicates the uplink burst profile in the UCD message, and is used along with ifIndex to identify an entry in the wmanIf2BsOfdmUcdBurstProfileTable." REFERENCE "Subclause 8.3.6.3.1, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmUcdBurstProfileEntry 1 } wmanIf2BsOfdmUcdFecCodeType OBJECT-TYPE SYNTAX WmanIf2OfdmFecCodeType MAX-ACCESS read-create STATUS current DESCRIPTION "Uplink FEC code type and modulation type" REFERENCE "Table 356, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmUcdBurstProfileEntry 2 } wmanIf2BsOfdmFocusCtPowerBoost OBJECT-TYPE SYNTAX INTEGER (0 .. 255) MAX-ACCESS read-create STATUS current DESCRIPTION "The power boost in dB of focused contention carriers, as described in 8.3.6.3.3." REFERENCE "Table 356, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmUcdBurstProfileEntry 3 } wmanIf2BsOfdmUcdTcsEnable OBJECT-TYPE SYNTAX INTEGER {tcsDisabled(0), tcsEnabled(1)} MAX-ACCESS read-create STATUS current DESCRIPTION "This parameter determines the transmission convergence sublayer, as described in 8.1.4.3, can be enabled on a per-burst basis for both uplink and downlink. through DIUC/UIUC messages." REFERENCE "Table 356, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmUcdBurstProfileEntry 4 } wmanIf2BsOfdmUcdBurstProfileRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table. If the implementator of this MIB has choosen not to implement 'dynamic assignment' of profiles, this object is not useful and should return noSuchName upon SNMP request." ::= { wmanIf2BsOfdmUcdBurstProfileEntry 5 } wmanIf2BsOfdmDcdBurstProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2BsOfdmDcdBurstProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each DCD burst profile. This table is double indexed. The primary index is an ifIndex with an ifType of propBWAp2Mp. The secondary index is wmanIf2BsOfdmDiucIndex." REFERENCE "Table 362, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmPhy 4 } wmanIf2BsOfdmDcdBurstProfileEntry OBJECT-TYPE SYNTAX WmanIf2BsOfdmDcdBurstProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each DCD burst profile. This table is double indexed. The primary index is an ifIndex with an ifType of propBWAp2Mp. The secondary index is wmanIf2BsOfdmDiucIndex." INDEX { ifIndex, wmanIf2BsOfdmDiucIndex } ::= { wmanIf2BsOfdmDcdBurstProfileTable 1 } WmanIf2BsOfdmDcdBurstProfileEntry ::= SEQUENCE { wmanIf2BsOfdmDiucIndex INTEGER, wmanIf2BsOfdmDownlinkFrequency Unsigned32, wmanIf2BsOfdmDcdFecCodeType WmanIf2OfdmFecCodeType, wmanIf2BsOfdmDiucMandatoryExitThresh INTEGER, wmanIf2BsOfdmDiucMinEntryThresh INTEGER, wmanIf2BsOfdmTcsEnable INTEGER, wmanIf2BsOfdmDcdBurstProfileRowStatus RowStatus} wmanIf2BsOfdmDiucIndex OBJECT-TYPE SYNTAX INTEGER (1..11) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Downlink Interval Usage Code indicates the downlink burst profile in the DCD message, and is used along with ifIndex to identify an entry in the wmanIf2BsOfdmDcdBurstProfileTable." REFERENCE "Subclause 8.3.6.3.1, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmDcdBurstProfileEntry 1 } wmanIf2BsOfdmDownlinkFrequency OBJECT-TYPE SYNTAX Unsigned32 UNITS "kHz" MAX-ACCESS read-create STATUS current DESCRIPTION "Downlink Frequency (kHz)." REFERENCE "Table 359, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmDcdBurstProfileEntry 2 } wmanIf2BsOfdmDcdFecCodeType OBJECT-TYPE SYNTAX WmanIf2OfdmFecCodeType MAX-ACCESS read-create STATUS current DESCRIPTION "Downlink FEC code type and modulation type" REFERENCE "Table 362, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmDcdBurstProfileEntry 3 } wmanIf2BsOfdmDiucMandatoryExitThresh OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "DIUC mandatory exit threshold: 0 - 63.75 dB CINR at or below where this DIUC can no longer be used and where this change to a more robust DIUC is required in 0.25 dB units." REFERENCE "Table 362, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmDcdBurstProfileEntry 4 } wmanIf2BsOfdmDiucMinEntryThresh OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "DIUC minimum entry threshold: 0 - 63.75 dB The minimum CINR required to start using this DIUC when changing from a more robust DIUC is required, in 0.25 dB units." REFERENCE "Table 362, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmDcdBurstProfileEntry 5 } wmanIf2BsOfdmTcsEnable OBJECT-TYPE SYNTAX INTEGER {tcsDisabled (0), tcsEnabled (1)} MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether Transmission COnvergence Sublayer is enabled or disabled." REFERENCE "Table 362, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmDcdBurstProfileEntry 6 } wmanIf2BsOfdmDcdBurstProfileRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table. If the implementator of this MIB has choosen not to implement 'dynamic assignment' of profiles, this object is not useful and should return noSuchName upon SNMP request." ::= { wmanIf2BsOfdmDcdBurstProfileEntry 7 } wmanIf2BsOfdmConfigurationTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2BsOfdmConfigurationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains BS configuration objects, specific to OFDM PHY." ::= { wmanIf2BsOfdmPhy 5 } wmanIf2BsOfdmConfigurationEntry OBJECT-TYPE SYNTAX WmanIf2BsOfdmConfigurationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is indexed by ifIndex with an ifType of propBWAp2Mp." INDEX { ifIndex } ::= { wmanIf2BsOfdmConfigurationTable 1 } WmanIf2BsOfdmConfigurationEntry ::= SEQUENCE { wmanIf2BsOfdmMinReqRegionFullTxOpp INTEGER, wmanIf2BsOfdmMinFocusedCtTxOpp INTEGER, wmanIf2BsOfdmMaxRoundTripDelay INTEGER, wmanIf2BsOfdmRangeAbortTimingThold INTEGER, wmanIf2BsOfdmRangeAbortPowerThold INTEGER, wmanIf2BsOfdmRangeAbortFreqThold INTEGER, wmanIf2BsOfdmDnlkRateId INTEGER, wmanIf2BsOfdmRatioG INTEGER} wmanIf2BsOfdmMinReqRegionFullTxOpp OBJECT-TYPE SYNTAX INTEGER (1..65535) UNITS "1/sec" MAX-ACCESS read-write STATUS current DESCRIPTION "The minimum number of Full bandwidth Req-Region Full Transmit opportunities scheduled in the UL per second." REFERENCE "Subclause 6.3.7.4.3 in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmConfigurationEntry 1 } wmanIf2BsOfdmMinFocusedCtTxOpp OBJECT-TYPE SYNTAX INTEGER (0..65535) UNITS "1/sec" MAX-ACCESS read-write STATUS current DESCRIPTION "The minimum number of focused contention Transmit opportunities scheduled in the UL per second. The value may be 0 if the focused contention is not implemented." REFERENCE "Subclauses 6.3.6.4 and 8.3.7.3.3 in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmConfigurationEntry 2 } wmanIf2BsOfdmMaxRoundTripDelay OBJECT-TYPE SYNTAX INTEGER (1..65535) UNITS "us" MAX-ACCESS read-write STATUS current DESCRIPTION "Maximum supported round trip delay. It is required to limit the cell size." REFERENCE "Subclause 8.3.5.1 in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmConfigurationEntry 3 } wmanIf2BsOfdmRangeAbortTimingThold OBJECT-TYPE SYNTAX INTEGER (0..255) UNITS "1/Fs" MAX-ACCESS read-write STATUS current DESCRIPTION "This object defines Tolerable Timing Offset. BS performs Initial Ranging until the SS transmissions are within limits that are deemed tolerable by the BS. If the SS does not transmit within these limits after a number of correction attempts then the BS aborts Initial Ranging." REFERENCE "Figure 63 and Table 365 in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmConfigurationEntry 4 } wmanIf2BsOfdmRangeAbortPowerThold OBJECT-TYPE SYNTAX INTEGER (0..255) UNITS "0.25dB" MAX-ACCESS read-write STATUS current DESCRIPTION "This object defines Tolerable Power Offset. BS performs Initial Ranging until the SS transmissions are within limits that are deemed tolerable by the BS. If the SS does not transmit within these limits after a number of correction attempts then the BS aborts Initial Ranging." REFERENCE "Figure 63 and Table 365 in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmConfigurationEntry 5 } wmanIf2BsOfdmRangeAbortFreqThold OBJECT-TYPE SYNTAX INTEGER (0..255) UNITS "Hz" MAX-ACCESS read-write STATUS current DESCRIPTION "This object defines Tolerable Frequency Offset. BS performs Initial Ranging until the SS transmissions are within limits that are deemed tolerable by the BS. If the SS does not transmit within these limits after a number of correction attempts then the BS aborts Initial Ranging." REFERENCE "Figure 63 and Table 365 in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmConfigurationEntry 6 } wmanIf2BsOfdmDnlkRateId OBJECT-TYPE SYNTAX INTEGER {dnlkRateIdBpsk1Over2(0), dnlkRateIdQpsk1Over2(1), dnlkRateIdQpsk3Over4(2), dnlkRateId16Qam1Over2(3), dnlkRateId16Qam3Over4(4), dnlkRateId64Qam2Over3(5), dnlkRateId64Qam3Over4(6)} MAX-ACCESS read-write STATUS current DESCRIPTION "The Rate ID to be used in the first downlink burst immediately following the FCH. The Rate ID encoding is static and cannot be changed during system operation. The change of the Rate ID should be applied on system re-intialisation (e.g. following sector or BS reset)." REFERENCE "Subclause 8.3.3.4.3 in IEEE Std 802.16-2004" DEFVAL { dnlkRateIdBpsk1Over2 } ::= { wmanIf2BsOfdmConfigurationEntry 7 } wmanIf2BsOfdmRatioG OBJECT-TYPE SYNTAX INTEGER {ratio1To4(0), ratio1To8(1), ratio1To16(2), ratio1To32(3)} MAX-ACCESS read-write STATUS current DESCRIPTION "The ratio of CP time to 'useful' time.Values are 1/4, 1/8, 1/16 or 1/32." REFERENCE "Subclause 8.3.1.1.1 in IEEE Std 802.16-2004" DEFVAL { ratio1To4 } ::= { wmanIf2BsOfdmConfigurationEntry 8 } wmanIf2BsSsOfdmReqCapabilitiesTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2BsSsOfdmReqCapabilitiesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the basic capability information, specific to OFDM Phy, of SSs that have been reported by SSs to BS using RNG-REQ, SBC-REQ and REG-REQ messages. Entries in this table should be created when an SS registers with a BS." ::= { wmanIf2BsOfdmPhy 6 } wmanIf2BsSsOfdmReqCapabilitiesEntry OBJECT-TYPE SYNTAX WmanIf2BsSsOfdmReqCapabilitiesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each SS that has been registered in the BS. This table augments the table wmanIf2BsRegisteredSsTable." AUGMENTS { wmanIf2BsRegisteredSsEntry } ::= { wmanIf2BsSsOfdmReqCapabilitiesTable 1 } WmanIf2BsSsOfdmReqCapabilitiesEntry ::= SEQUENCE { wmanIf2BsSsOfdmReqCapFftSizes WmanIf2OfdmFftSizes, wmanIf2BsSsOfdmReqCapSsDemodulator WmanIf2OfdmSsDeModType, wmanIf2BsSsOfdmReqCapSsModulator WmanIf2OfdmSsModType, wmanIf2BsSsOfdmReqCapFocusedCtSupport WmanIf2OfdmFocusedCt, wmanIf2BsSsOfdmReqCapTcSublayerSupport WmanIf2OfdmTcSublayer, wmanIf2eBsSsOfdmReqCapPrivteMapSupport WmanIf2eOfdmPrivMap, wmanIf2eBsSsOfdmReqCapUlPowerControl WmanIf2eOfdmUlPower, wmanIf2eBsSsOfdmReqCapLoopPwrControlSw Unsigned32} wmanIf2BsSsOfdmReqCapFftSizes OBJECT-TYPE SYNTAX WmanIf2OfdmFftSizes MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the FFT sizes supported by SS. The usage is defined by WmanIf2OfdmFftSizes." ::= { wmanIf2BsSsOfdmReqCapabilitiesEntry 1 } wmanIf2BsSsOfdmReqCapSsDemodulator OBJECT-TYPE SYNTAX WmanIf2OfdmSsDeModType MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the different demodulator options supported by SS for downlink. The usage is defined by WmanIf2OfdmSsDeModType." ::= { wmanIf2BsSsOfdmReqCapabilitiesEntry 2 } wmanIf2BsSsOfdmReqCapSsModulator OBJECT-TYPE SYNTAX WmanIf2OfdmSsModType MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the different modulator options supported by SS for uplink. The usage is defined by WmanIf2OfdmSsModType." ::= { wmanIf2BsSsOfdmReqCapabilitiesEntry 3 } wmanIf2BsSsOfdmReqCapFocusedCtSupport OBJECT-TYPE SYNTAX WmanIf2OfdmFocusedCt MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates whether the SS supports Focused Contention. The usage is defined by WmanIf2OfdmFocusedCt." ::= { wmanIf2BsSsOfdmReqCapabilitiesEntry 4 } wmanIf2BsSsOfdmReqCapTcSublayerSupport OBJECT-TYPE SYNTAX WmanIf2OfdmTcSublayer MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates whether or not the SS supports the TC sublayer. The usage is defined by WmanIf2OfdmTcSublayer." ::= { wmanIf2BsSsOfdmReqCapabilitiesEntry 5 } wmanIf2eBsSsOfdmReqCapPrivteMapSupport OBJECT-TYPE SYNTAX WmanIf2eOfdmPrivMap MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates if the private map parameters is supported." ::= { wmanIf2BsSsOfdmReqCapabilitiesEntry 6 } wmanIf2eBsSsOfdmReqCapUlPowerControl OBJECT-TYPE SYNTAX WmanIf2eOfdmUlPower MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the uplink power control options supported by SS." ::= { wmanIf2BsSsOfdmReqCapabilitiesEntry 7 } wmanIf2eBsSsOfdmReqCapLoopPwrControlSw OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates he minimum number of frames that SS takes to switch from the open loop power control scheme to the closed loop power control scheme or vice versa." ::= { wmanIf2BsSsOfdmReqCapabilitiesEntry 8 } wmanIf2BsSsOfdmRspCapabilitiesTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2BsSsOfdmRspCapabilitiesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the basic capability information, specific to OFDM Phy, of SSs that have been negotiated and agreed between BS and SS via RNG-REQ/RSP, SBC-REQ/RSP and REG-REQ/RSP messages. This table augments the wmanIf2BsRegisteredSsTable." REFERENCE "Subclause 6.3.2.3.7 in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmPhy 7 } wmanIf2BsSsOfdmRspCapabilitiesEntry OBJECT-TYPE SYNTAX WmanIf2BsSsOfdmRspCapabilitiesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each SS that has been registered in the BS. This table augments the wmanIf2BsRegisteredSsTable. " AUGMENTS { wmanIf2BsRegisteredSsEntry } ::= { wmanIf2BsSsOfdmRspCapabilitiesTable 1 } WmanIf2BsSsOfdmRspCapabilitiesEntry ::= SEQUENCE { wmanIf2BsSsOfdmRspCapFftSizes WmanIf2OfdmFftSizes, wmanIf2BsSsOfdmRspCapSsDemodulator WmanIf2OfdmSsDeModType, wmanIf2BsSsOfdmRspCapSsModulator WmanIf2OfdmSsModType, wmanIf2BsSsOfdmRspCapFocusedCtSupport WmanIf2OfdmFocusedCt, wmanIf2BsSsOfdmRspCapTcSublayerSupport WmanIf2OfdmTcSublayer, wmanIf2eBsSsOfdmRspCapPrivteMapSupport WmanIf2eOfdmPrivMap, wmanIf2eBsSsOfdmRspCapUlPowerControl WmanIf2eOfdmUlPower, wmanIf2eBsSsOfdmRspCapLoopPwrControlSw Unsigned32} wmanIf2BsSsOfdmRspCapFftSizes OBJECT-TYPE SYNTAX WmanIf2OfdmFftSizes MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the FFT sizes negotiated with the SS. The usage is defined by WmanIf2OfdmFftSizes." ::= { wmanIf2BsSsOfdmRspCapabilitiesEntry 1 } wmanIf2BsSsOfdmRspCapSsDemodulator OBJECT-TYPE SYNTAX WmanIf2OfdmSsDeModType MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the different demodulator options negotiated for SS for downlink. The usage is defined by WmanIf2OfdmSsDeModType." ::= { wmanIf2BsSsOfdmRspCapabilitiesEntry 2 } wmanIf2BsSsOfdmRspCapSsModulator OBJECT-TYPE SYNTAX WmanIf2OfdmSsModType MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the different modulator options negotiated for SS for uplink. The usage is defined by WmanIf2OfdmSsModType." ::= { wmanIf2BsSsOfdmRspCapabilitiesEntry 3 } wmanIf2BsSsOfdmRspCapFocusedCtSupport OBJECT-TYPE SYNTAX WmanIf2OfdmFocusedCt MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates whether the SS has negotiated the support for Focused Contention. The usage is defined by WmanIf2OfdmFocusedCt." ::= { wmanIf2BsSsOfdmRspCapabilitiesEntry 4 } wmanIf2BsSsOfdmRspCapTcSublayerSupport OBJECT-TYPE SYNTAX WmanIf2OfdmTcSublayer MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates whether the SS has negotiated support for the TC sublayer. The usage is defined by WmanIf2OfdmTcSublayer." ::= { wmanIf2BsSsOfdmRspCapabilitiesEntry 5 } wmanIf2eBsSsOfdmRspCapPrivteMapSupport OBJECT-TYPE SYNTAX WmanIf2eOfdmPrivMap MAX-ACCESS read-only STATUS current DESCRIPTION "This field iindicates if the private map parameters is supported." ::= { wmanIf2BsSsOfdmRspCapabilitiesEntry 6 } wmanIf2eBsSsOfdmRspCapUlPowerControl OBJECT-TYPE SYNTAX WmanIf2eOfdmUlPower MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the uplink power control options supported by SS." ::= { wmanIf2BsSsOfdmRspCapabilitiesEntry 7 } wmanIf2eBsSsOfdmRspCapLoopPwrControlSw OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates he minimum number of frames that SS takes to switch from the open loop power control scheme to the closed loop power control scheme or vice versa." ::= { wmanIf2BsSsOfdmRspCapabilitiesEntry 8 } wmanIf2BsOfdmCapabilitiesTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2BsOfdmCapabilitiesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the basic capabilities, specific to OFDM Phy, of the BS as implemented in BS hardware and software. These capabilities along with the configuration for them (wmanIf2BsOfdmCapabilitiesConfigTable) are used for negotiation of basic capabilities with SS using RNG-RSP, SBC-RSP and REG-RSP messages. The negotiated capabilities are obtained by interSubclause of SS raw reported capabilities, BS raw capabilities and BS configured capabilities. The objects in the table have read-only access. The table is maintained by BS." ::= { wmanIf2BsOfdmPhy 8 } wmanIf2BsOfdmCapabilitiesEntry OBJECT-TYPE SYNTAX WmanIf2BsOfdmCapabilitiesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each BS sector and is indexed by ifIndex." INDEX { ifIndex } ::= { wmanIf2BsOfdmCapabilitiesTable 1 } WmanIf2BsOfdmCapabilitiesEntry ::= SEQUENCE { wmanIf2BsOfdmCapFftSizes WmanIf2OfdmFftSizes, wmanIf2BsOfdmCapSsDemodulator WmanIf2OfdmSsDeModType, wmanIf2BsOfdmCapSsModulator WmanIf2OfdmSsModType, wmanIf2BsOfdmCapFocusedCtSupport WmanIf2OfdmFocusedCt, wmanIf2BsOfdmCapTcSublayerSupport WmanIf2OfdmTcSublayer, wmanIf2eBsOfdmCapPrivteMapSupport WmanIf2eOfdmPrivMap, wmanIf2eBsSsOfdmCapUlPowerControl WmanIf2eOfdmUlPower, wmanIf2eBsSsOfdmCapLoopPwrControlSw Unsigned32} wmanIf2BsOfdmCapFftSizes OBJECT-TYPE SYNTAX WmanIf2OfdmFftSizes MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the FFT sizes supported by the BS. The usage is defined by WmanIf2OfdmFftSizes." ::= { wmanIf2BsOfdmCapabilitiesEntry 1 } wmanIf2BsOfdmCapSsDemodulator OBJECT-TYPE SYNTAX WmanIf2OfdmSsDeModType MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the different BS demodulator options for uplink supported by the BS. The usage is defined by WmanIf2OfdmSsDeModType." ::= { wmanIf2BsOfdmCapabilitiesEntry 2 } wmanIf2BsOfdmCapSsModulator OBJECT-TYPE SYNTAX WmanIf2OfdmSsModType MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the different BS modulator options for downlink supported by the BS. The usage is defined by WmanIf2OfdmSsModType." ::= { wmanIf2BsOfdmCapabilitiesEntry 3 } wmanIf2BsOfdmCapFocusedCtSupport OBJECT-TYPE SYNTAX WmanIf2OfdmFocusedCt MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the BS support for Focused Contention. The usage is defined by WmanIf2OfdmFocusedCt." ::= { wmanIf2BsOfdmCapabilitiesEntry 4 } wmanIf2BsOfdmCapTcSublayerSupport OBJECT-TYPE SYNTAX WmanIf2OfdmTcSublayer MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the BS supports for TC sublayer. The usage is defined by WmanIf2OfdmTcSublayer." ::= { wmanIf2BsOfdmCapabilitiesEntry 5 } wmanIf2eBsOfdmCapPrivteMapSupport OBJECT-TYPE SYNTAX WmanIf2eOfdmPrivMap MAX-ACCESS read-only STATUS current DESCRIPTION "This field iindicates if the private map parameters is supported." ::= { wmanIf2BsOfdmCapabilitiesEntry 6 } wmanIf2eBsSsOfdmCapUlPowerControl OBJECT-TYPE SYNTAX WmanIf2eOfdmUlPower MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the uplink power control options supported by SS." ::= { wmanIf2BsOfdmCapabilitiesEntry 7 } wmanIf2eBsSsOfdmCapLoopPwrControlSw OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates he minimum number of frames that SS takes to switch from the open loop power control scheme to the closed loop power control scheme or vice versa." ::= { wmanIf2BsOfdmCapabilitiesEntry 8 } wmanIf2BsOfdmCapabilitiesConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2BsOfdmCapabilitiesConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the configuration for basic capabilities of BS, specific to OFDM Phy. The table is intended to be used to restrict the Capabilities implemented by BS, for example in order to comply with local regulatory requirements. The BS should use the configuration along with the implemented Capabilities (wmanIf2BsOfdmPhyTable) for negotiation of basic capabilities with SS using RNG-RSP, SBC-RSP and REG-RSP messages. The negotiated capabilities are obtained by interSubclause of SS reported capabilities, BS raw capabilities and BS configured capabilities. The objects in the table have read-write access. The rows are created by BS as a copy of wmanIf2BsBasicCapabilitiesTable and can be modified by NMS." ::= { wmanIf2BsOfdmPhy 9 } wmanIf2BsOfdmCapabilitiesConfigEntry OBJECT-TYPE SYNTAX WmanIf2BsOfdmCapabilitiesConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each BS sector and is indexed by ifIndex." INDEX { ifIndex } ::= { wmanIf2BsOfdmCapabilitiesConfigTable 1 } WmanIf2BsOfdmCapabilitiesConfigEntry ::= SEQUENCE { wmanIf2BsOfdmCapCfgFftSizes WmanIf2OfdmFftSizes, wmanIf2BsOfdmCapCfgSsDemodulator WmanIf2OfdmSsDeModType, wmanIf2BsOfdmCapCfgSsModulator WmanIf2OfdmSsModType, wmanIf2BsOfdmCapCfgFocusedCtSupport WmanIf2OfdmFocusedCt, wmanIf2BsOfdmCapCfgTcSublayerSupport WmanIf2OfdmTcSublayer, wmanIf2eBsOfdmCapCfgPrivteMapSupport WmanIf2eOfdmPrivMap, wmanIf2eBsSsOfdmCapCfgUlPowerControl WmanIf2eOfdmUlPower, wmanIf2eBsSsOfdmCapCfgLoopPwrControlSw Unsigned32} wmanIf2BsOfdmCapCfgFftSizes OBJECT-TYPE SYNTAX WmanIf2OfdmFftSizes MAX-ACCESS read-write STATUS current DESCRIPTION "This field indicates the FFT sizes support configured for the BS. The usage is defined by WmanIf2OfdmFftSizes." ::= { wmanIf2BsOfdmCapabilitiesConfigEntry 1 } wmanIf2BsOfdmCapCfgSsDemodulator OBJECT-TYPE SYNTAX WmanIf2OfdmSsDeModType MAX-ACCESS read-write STATUS current DESCRIPTION "This field indicates the different BS demodulator options configured for uplink. The usage is defined by WmanIf2OfdmSsDeModType." ::= { wmanIf2BsOfdmCapabilitiesConfigEntry 2 } wmanIf2BsOfdmCapCfgSsModulator OBJECT-TYPE SYNTAX WmanIf2OfdmSsModType MAX-ACCESS read-write STATUS current DESCRIPTION "This field indicates the different BS modulator options configured for downlink. The usage is defined by WmanIf2OfdmSsModType." ::= { wmanIf2BsOfdmCapabilitiesConfigEntry 3 } wmanIf2BsOfdmCapCfgFocusedCtSupport OBJECT-TYPE SYNTAX WmanIf2OfdmFocusedCt MAX-ACCESS read-write STATUS current DESCRIPTION "This field indicates the BS support configured for Focused Contention. The usage is defined by WmanIf2OfdmFocusedCt." ::= { wmanIf2BsOfdmCapabilitiesConfigEntry 4 } wmanIf2BsOfdmCapCfgTcSublayerSupport OBJECT-TYPE SYNTAX WmanIf2OfdmTcSublayer MAX-ACCESS read-write STATUS current DESCRIPTION "This field indicates the BS support configured for TC sublayer. The usage is defined by WmanIf2OfdmTcSublayer." ::= { wmanIf2BsOfdmCapabilitiesConfigEntry 5 } wmanIf2eBsOfdmCapCfgPrivteMapSupport OBJECT-TYPE SYNTAX WmanIf2eOfdmPrivMap MAX-ACCESS read-write STATUS current DESCRIPTION "This field iindicates if the private map parameters is supported." ::= { wmanIf2BsOfdmCapabilitiesConfigEntry 6 } wmanIf2eBsSsOfdmCapCfgUlPowerControl OBJECT-TYPE SYNTAX WmanIf2eOfdmUlPower MAX-ACCESS read-write STATUS current DESCRIPTION "This field indicates the uplink power control options supported by SS." ::= { wmanIf2BsOfdmCapabilitiesConfigEntry 7 } wmanIf2eBsSsOfdmCapCfgLoopPwrControlSw OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This field indicates he minimum number of frames that SS takes to switch from the open loop power control scheme to the closed loop power control scheme or vice versa." ::= { wmanIf2BsOfdmCapabilitiesConfigEntry 8 } -- -- BS OFDMA PHY objects -- wmanIf2BsOfdmaPhy OBJECT IDENTIFIER ::= { wmanIf2BsPhy 2 } wmanIf2BsOfdmaUplinkChannelTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2BsOfdmaUplinkChannelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains UCD channel attributes, defining the transmission characteristics of uplink channels" REFERENCE "Table 349 and Table 353, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmaPhy 1 } wmanIf2BsOfdmaUplinkChannelEntry OBJECT-TYPE SYNTAX WmanIf2BsOfdmaUplinkChannelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each uplink channel of multi-sector BS, and is indexed by BS ifIndex. An entry in this table exists for each ifEntry of BS with an ifType of propBWAp2Mp." INDEX { ifIndex } ::= { wmanIf2BsOfdmaUplinkChannelTable 1 } WmanIf2BsOfdmaUplinkChannelEntry ::= SEQUENCE { wmanIf2BsOfdmaCtBasedResvTimeout INTEGER, wmanIf2BsOfdmaBwReqOppSize INTEGER, wmanIf2BsOfdmaRangReqOppSize INTEGER, wmanIf2BsOfdmaUplinkCenterFreq Unsigned32, wmanIf2BsOfdmaInitRngCodes INTEGER, wmanIf2BsOfdmaPeriodicRngCodes INTEGER, wmanIf2BsOfdmaBWReqCodes INTEGER, wmanIf2BsOfdmaPerRngBackoffStart INTEGER, wmanIf2BsOfdmaPerRngBackoffEnd INTEGER, wmanIf2eBsOfdmaStartOfRngCodes INTEGER, wmanIf2BsOfdmaPermutationBase INTEGER, wmanIf2BsOfdmaULAllocSubchBitmap OCTET STRING, wmanIf2BsOfdmaOptPermULAllocSubchBitmap OCTET STRING, wmanIf2BsOfdmaBandAMCAllocThreshold INTEGER, wmanIf2BsOfdmaBandAMCReleaseThreshold INTEGER, wmanIf2BsOfdmaBandAMCAllocTimer INTEGER, wmanIf2BsOfdmaBandAMCReleaseTimer INTEGER, wmanIf2BsOfdmaBandStatRepMAXPeriod INTEGER, wmanIf2BsOfdmaBandAMCRetryTimer INTEGER, wmanIf2BsOfdmaSafetyChAllocThreshold INTEGER, wmanIf2BsOfdmaSafetyChReleaseThreshold INTEGER, wmanIf2BsOfdmaSafetyChAllocTimer INTEGER, wmanIf2BsOfdmaSafetyChReleaseTimer INTEGER, wmanIf2BsOfdmaBinStatRepMAXPeriod INTEGER, wmanIf2BsOfdmaSafetyChaRetryTimer INTEGER, wmanIf2BsOfdmaHARQAackDelayULBurst INTEGER, wmanIf2BsOfdmaCQICHBandAMCTranaDelay INTEGER} wmanIf2BsOfdmaCtBasedResvTimeout OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-write STATUS current DESCRIPTION "The number of UL-MAPs to receive before contention-based reservation is attempted again for the same connection." REFERENCE "Table 349, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmaUplinkChannelEntry 1 } wmanIf2BsOfdmaBwReqOppSize OBJECT-TYPE SYNTAX INTEGER (1..65535) UNITS "PS" MAX-ACCESS read-write STATUS current DESCRIPTION "Size (in units of PS) of PHY payload that SS may use to format and transmit a bandwidth request message in a contention request opportunity. The value includes all PHY overhead as well as allowance for the MAC data the message may hold." REFERENCE "Table 349, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmaUplinkChannelEntry 2 } wmanIf2BsOfdmaRangReqOppSize OBJECT-TYPE SYNTAX INTEGER (1..65535) UNITS "PS" MAX-ACCESS read-write STATUS current DESCRIPTION "Size (in units of PS) of PHY payload that SS may use to format and transmit a RNG-REQ message in a contention request opportunity. The value includes all PHY overhead as well as allowance for the MAC data the message may hold and the maxiumum SS/BS roundtrip propagation delay." REFERENCE "Table 349, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmaUplinkChannelEntry 3 } wmanIf2BsOfdmaUplinkCenterFreq OBJECT-TYPE SYNTAX Unsigned32 UNITS "kHz" MAX-ACCESS read-write STATUS current DESCRIPTION " Uplink center frequency (kHz)" REFERENCE "Table 349, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmaUplinkChannelEntry 4 } wmanIf2BsOfdmaInitRngCodes OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-write STATUS deprecated DESCRIPTION "Number of initial ranging CDMA codes. Possible values are 0..255. The total number of wmanIf2BsOfdmaInitRngCodes, wmanIf2BsOfdmaPeriodicRngCodes and wmanIf2BsOfdmaBWReqCodes shall be equal or less than 256." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16-2004" DEFVAL { 30 } ::= { wmanIf2BsOfdmaUplinkChannelEntry 5 } wmanIf2BsOfdmaPeriodicRngCodes OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-write STATUS deprecated DESCRIPTION "Number of periodic ranging CDMA codes. Possible values are 0..255. The total number of wmanIf2BsOfdmaInitRngCodes, wmanIf2BsOfdmaPeriodicRngCodes and wmanIf2BsOfdmaBWReqCodes shall be equal or less than 256." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16-2004" DEFVAL { 30 } ::= { wmanIf2BsOfdmaUplinkChannelEntry 6 } wmanIf2BsOfdmaBWReqCodes OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-write STATUS deprecated DESCRIPTION "Number of bandwidth request codes. Possible values are 0..255. The total number of wmanIf2BsOfdmaInitRngCodes, wmanIf2BsOfdmaPeriodicRngCodes and wmanIf2BsOfdmaBWReqCodes shall be equal or less than 256." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16-2004" DEFVAL { 30 } ::= { wmanIf2BsOfdmaUplinkChannelEntry 7 } wmanIf2BsOfdmaPerRngBackoffStart OBJECT-TYPE SYNTAX INTEGER (0..15) MAX-ACCESS read-write STATUS deprecated DESCRIPTION "Initial backoff window size for periodic ranging contention, , expressed as a power of 2. Range: 0..15 (the highest order bits shall be unused and set to 0)." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16-2004" DEFVAL { 0 } ::= { wmanIf2BsOfdmaUplinkChannelEntry 8 } wmanIf2BsOfdmaPerRngBackoffEnd OBJECT-TYPE SYNTAX INTEGER (0 .. 15) MAX-ACCESS read-write STATUS deprecated DESCRIPTION "Final backoff window size for periodic ranging contention, expressed as a power of 2. Range: 0..15 (the highest order bits shall be unused and set to 0)." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16-2004" DEFVAL { 15 } ::= { wmanIf2BsOfdmaUplinkChannelEntry 9 } wmanIf2eBsOfdmaStartOfRngCodes OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates the starting number, S, of the group of codes used for this uplink.All the ranging codes used on this uplink will be between S and ((S+N+M+L) mod 256). Where, N: the number of initial-ranging codes M: the number of periodic-ranging codes L: the number of bandwidth-request codes O: the number of handover-ranging codes" REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16e-2005" DEFVAL { 0 } ::= { wmanIf2BsOfdmaUplinkChannelEntry 10 } wmanIf2BsOfdmaPermutationBase OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Determines the UL_PermBase parameter for the subcarrier permutation to be used on this uplink channel. UL_PermBase = 7 LSBs of Permutation base." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16-2004" DEFVAL { 0 } ::= { wmanIf2BsOfdmaUplinkChannelEntry 11 } wmanIf2BsOfdmaULAllocSubchBitmap OBJECT-TYPE SYNTAX OCTET STRING (SIZE (9)) MAX-ACCESS read-write STATUS current DESCRIPTION "This is a bitmap describing the physical sub-channels allocated to the segment in the UL, when using the uplink PUSC permutation. The LSB of the first byte shall corrspond to subchannel 0. For any bit that is not set, the corresponding subchannel shall not be used by the SS on that segment" REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16e-2005" ::= { wmanIf2BsOfdmaUplinkChannelEntry 12 } wmanIf2BsOfdmaOptPermULAllocSubchBitmap OBJECT-TYPE SYNTAX OCTET STRING (SIZE (13)) MAX-ACCESS read-write STATUS current DESCRIPTION "This is a bitmap describing the sub-channels allocated to the segment in the UL, when using the uplink optional PUSC permutation (see 8.4.6.2.5 in IEEE Std 802.16-2004). The LSB of the first byte shall correspond to subchannel 0. For any bit that is not set, the corresponding subchannel shall not be used by the SS on that segment. When this TLV is not present, BS may allocate any subchannels to an SS." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmaUplinkChannelEntry 13 } wmanIf2BsOfdmaBandAMCAllocThreshold OBJECT-TYPE SYNTAX INTEGER (0 .. 255) UNITS "dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Threshold of the maximum of the standard deviations of the individual bands CINR measurements over time to trigger mode transition from normal subchannel to Band AMC" REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16e-2005" ::= { wmanIf2BsOfdmaUplinkChannelEntry 14 } wmanIf2BsOfdmaBandAMCReleaseThreshold OBJECT-TYPE SYNTAX INTEGER (0 .. 255) UNITS "dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Threshold of the maximum of the standard deviations of the individual bands CINR measurements over time to trigger mode transition from Band AMC to normal subchannel" REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16e-2005" ::= { wmanIf2BsOfdmaUplinkChannelEntry 15 } wmanIf2BsOfdmaBandAMCAllocTimer OBJECT-TYPE SYNTAX INTEGER (0 .. 255) UNITS "Frame" MAX-ACCESS read-write STATUS current DESCRIPTION "Minimum required number of frames to measure the average and standard deviation for the event of Band AMC triggering" REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16e-2005" ::= { wmanIf2BsOfdmaUplinkChannelEntry 16 } wmanIf2BsOfdmaBandAMCReleaseTimer OBJECT-TYPE SYNTAX INTEGER (0 .. 255) UNITS "Frame" MAX-ACCESS read-write STATUS current DESCRIPTION "Minimum required number of frames to measure the average and standard deviation for the event triggering from Band AMC to normal subchannel" REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16e-2005" ::= { wmanIf2BsOfdmaUplinkChannelEntry 17 } wmanIf2BsOfdmaBandStatRepMAXPeriod OBJECT-TYPE SYNTAX INTEGER (0 .. 255) UNITS "Frame" MAX-ACCESS read-write STATUS current DESCRIPTION "Maximum period between refreshing the Band CINR measurement by the unsolicited REP-RSP" REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16e-2005" ::= { wmanIf2BsOfdmaUplinkChannelEntry 18 } wmanIf2BsOfdmaBandAMCRetryTimer OBJECT-TYPE SYNTAX INTEGER (0 .. 255) UNITS "Frame" MAX-ACCESS read-write STATUS current DESCRIPTION "Backoff timer between consecutive mode transitions from normal subchannel to Band AMC when the previous request is failed" REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16e-2005" ::= { wmanIf2BsOfdmaUplinkChannelEntry 19 } wmanIf2BsOfdmaSafetyChAllocThreshold OBJECT-TYPE SYNTAX INTEGER (0 .. 255) UNITS "dB" MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This object defines the OFDMA safety channel allocation threshold." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmaUplinkChannelEntry 20 } wmanIf2BsOfdmaSafetyChReleaseThreshold OBJECT-TYPE SYNTAX INTEGER (0 .. 255) UNITS "dB" MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This object defines the OFDMA safety channel release threshold." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmaUplinkChannelEntry 21 } wmanIf2BsOfdmaSafetyChAllocTimer OBJECT-TYPE SYNTAX INTEGER (0 .. 255) UNITS "Frame" MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This object defines the OFDMA safety channel allocation timer." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmaUplinkChannelEntry 22 } wmanIf2BsOfdmaSafetyChReleaseTimer OBJECT-TYPE SYNTAX INTEGER (0 .. 255) UNITS "Frame" MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This object defines the OFDMA safety channel release timer." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmaUplinkChannelEntry 23 } wmanIf2BsOfdmaBinStatRepMAXPeriod OBJECT-TYPE SYNTAX INTEGER (0 .. 255) UNITS "Frame" MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This object defines the OFDMA bin status reporting maximum period." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmaUplinkChannelEntry 24 } wmanIf2BsOfdmaSafetyChaRetryTimer OBJECT-TYPE SYNTAX INTEGER (0 .. 255) UNITS "Frame" MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This object defines the OFDMA safety channel retry timer." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmaUplinkChannelEntry 25 } wmanIf2BsOfdmaHARQAackDelayULBurst OBJECT-TYPE SYNTAX INTEGER {oneframeoffset(1), twoframesoffset(2), threeframesoffset(3)} MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This object defines the OFDMA H-ARQ ACK delay for UL burst. 1 = one frame offset 2 = two frames offset 3 = three frames offset" REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmaUplinkChannelEntry 26 } wmanIf2BsOfdmaCQICHBandAMCTranaDelay OBJECT-TYPE SYNTAX INTEGER (0 .. 255) UNITS "Frame" MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This object defines the OFDMA CQICH band AMC transition delay." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmaUplinkChannelEntry 27 } wmanIf2BsOfdmaDownlinkChannelTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2BsOfdmaDownlinkChannelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains DCD channel attributes, defining the transmission characteristics of downlink channels" REFERENCE "Subclause 11.4.1, Table 358, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmaPhy 2 } wmanIf2BsOfdmaDownlinkChannelEntry OBJECT-TYPE SYNTAX WmanIf2BsOfdmaDownlinkChannelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each downlink channel of multi-sector BS, and is indexed by BS ifIndex. An entry in this table exists for each ifEntry of BS with an ifType of propBWAp2Mp." INDEX { ifIndex } ::= { wmanIf2BsOfdmaDownlinkChannelTable 1 } WmanIf2BsOfdmaDownlinkChannelEntry ::= SEQUENCE { wmanIf2BsOfdmaBsEIRP INTEGER, wmanIf2BsOfdmaChannelNumber WmanIf2ChannelNumber, wmanIf2BsOfdmaTTG INTEGER, wmanIf2BsOfdmaRTG INTEGER, wmanIf2BsOfdmaInitRngMaxRSS INTEGER, wmanIf2BsOfdmaDownlinkCenterFreq Unsigned32, wmanIf2BsOfdmaBsId WmanIf2BsIdType, wmanIf2BsOfdmaMacVersion WmanIf2MacVersion, wmanIf2BsOfdmaFrameDurationCode INTEGER, wmanIf2BsOfdmaSizeCqichIdField INTEGER, wmanIf2BsOfdmaHARQAackDelayBurst INTEGER} wmanIf2BsOfdmaBsEIRP OBJECT-TYPE SYNTAX INTEGER (-32768..32767) UNITS "dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "The EIRP is the equivalent isotropic radiated power of the base station, which is computed for a simple single-antenna transmitter." REFERENCE "Subclause 11.4.1, Table 358, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmaDownlinkChannelEntry 1 } wmanIf2BsOfdmaChannelNumber OBJECT-TYPE SYNTAX WmanIf2ChannelNumber MAX-ACCESS read-write STATUS current DESCRIPTION "Downlink channel number as defined in 8.5. Used for license-exempt operation only." REFERENCE "Subclause 11.4.1, Table 358, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmaDownlinkChannelEntry 2 } wmanIf2BsOfdmaTTG OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Transmit / Receive Transition Gap." REFERENCE "Subclause 11.4.1, Table 358, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmaDownlinkChannelEntry 3 } wmanIf2BsOfdmaRTG OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Receive / Transmit Transition Gap." REFERENCE "Subclause 11.4.1, Table 358, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmaDownlinkChannelEntry 4 } wmanIf2BsOfdmaInitRngMaxRSS OBJECT-TYPE SYNTAX INTEGER (-32768..32767) UNITS "dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "Initial Ranging Max. equivalent isotropic received power at BS Signed in units of 1 dBm." REFERENCE "Subclause 11.4.1, Table 358, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmaDownlinkChannelEntry 5 } wmanIf2BsOfdmaDownlinkCenterFreq OBJECT-TYPE SYNTAX Unsigned32 UNITS "kHz" MAX-ACCESS read-write STATUS current DESCRIPTION "Downlink center frequency (kHz)." REFERENCE "Subclause 11.4.1, Table 358, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmaDownlinkChannelEntry 6 } wmanIf2BsOfdmaBsId OBJECT-TYPE SYNTAX WmanIf2BsIdType MAX-ACCESS read-write STATUS current DESCRIPTION "Base station ID." REFERENCE "Subclause 11.4.1, Table 358, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmaDownlinkChannelEntry 7 } wmanIf2BsOfdmaMacVersion OBJECT-TYPE SYNTAX WmanIf2MacVersion MAX-ACCESS read-write STATUS current DESCRIPTION "This parameter specifies the version of 802.16 to which the message originator conforms." REFERENCE "Subclause 11.4.1, Table 358, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmaDownlinkChannelEntry 8 } wmanIf2BsOfdmaFrameDurationCode OBJECT-TYPE SYNTAX INTEGER {aASGap(0), duration2ms(1), duration2dot5ms(2), duration4ms(3), duration5ms(4), duration8ms(5), duration10ms(6), duration12dot5ms(7), duration20ms(8)} MAX-ACCESS read-write STATUS current DESCRIPTION "The duration of the frame. The frame duration code values are specified in Table 274." REFERENCE "Table 273, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmaDownlinkChannelEntry 9 } wmanIf2BsOfdmaSizeCqichIdField OBJECT-TYPE SYNTAX INTEGER {threebits(1), fourbits(2), fivebits(3), sixbits(4), sevenbits(5), eightbits(6), ninebits(7)} MAX-ACCESS read-write STATUS current DESCRIPTION "This object defines the size of CQICH ID field. 0 = Reserved 1 = 3 bits 2 = 4 bits 3 = 5 bits 4 = 6 bits 5 = 7 bits 6 = 8 bits 7 = 9 bits 8...255 = Reserved" REFERENCE "Subclause 11.3.1, Table 358, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmaDownlinkChannelEntry 10 } wmanIf2BsOfdmaHARQAackDelayBurst OBJECT-TYPE SYNTAX INTEGER {oneframeoffset(1), twoframesoffset(2), threeframesoffset(3)} MAX-ACCESS read-write STATUS current DESCRIPTION "This object defines the OFDMA H-ARQ ACK delay for DL burst. 1 = one frame offset 2 = two frames offset 3 = three frames offset" REFERENCE "Subclause 11.3.1, Table 358, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmaDownlinkChannelEntry 11 } wmanIf2BsOfdmaUcdBurstProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2BsOfdmaUcdBurstProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains UCD burst profiles for each uplink channel" REFERENCE "Table 356, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmaPhy 3 } wmanIf2BsOfdmaUcdBurstProfileEntry OBJECT-TYPE SYNTAX WmanIf2BsOfdmaUcdBurstProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each UCD burst profile. This table is double indexed. The primary index is an ifIndex with an ifType of propBWAp2Mp. The secondary index is wmanIf2BsOfdmaUiucIndex." INDEX { ifIndex, wmanIf2BsOfdmaUiucIndex } ::= { wmanIf2BsOfdmaUcdBurstProfileTable 1 } WmanIf2BsOfdmaUcdBurstProfileEntry ::= SEQUENCE { wmanIf2BsOfdmaUiucIndex INTEGER, wmanIf2BsOfdmaUcdFecCodeType WmanIf2OfdmaFecCodeType, wmanIf2BsOfdmaRangingDataRatio INTEGER, wmanIf2BsOfdmaNorCOverNOverride OCTET STRING, wmanIf2BsOfdmaUcdBurstProfileRowStatus RowStatus} wmanIf2BsOfdmaUiucIndex OBJECT-TYPE SYNTAX INTEGER (1 .. 10) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Uplink Interval Usage Code indicates the uplink burst profile in the UCD message, and is used along with ifIndex to identify an entry in the wmanIf2BsOfdmaUcdBurstProfileTable." REFERENCE "Subclause 8.4.5.4.1, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmaUcdBurstProfileEntry 1 } wmanIf2BsOfdmaUcdFecCodeType OBJECT-TYPE SYNTAX WmanIf2OfdmaFecCodeType MAX-ACCESS read-create STATUS current DESCRIPTION "Uplink FEC code type and modulation type" REFERENCE "Subclause 11.3.1.1, Table 357, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmaUcdBurstProfileEntry 2 } wmanIf2BsOfdmaRangingDataRatio OBJECT-TYPE SYNTAX INTEGER (0 .. 255) MAX-ACCESS read-create STATUS current DESCRIPTION "Reducing factor in units of 1 dB, between the power used for this burst and power should be used for CDMA Ranging." REFERENCE "Subclause 11.3.1.1, Table 357, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmaUcdBurstProfileEntry 3 } wmanIf2BsOfdmaNorCOverNOverride OBJECT-TYPE SYNTAX OCTET STRING (SIZE (5)) MAX-ACCESS read-create STATUS current DESCRIPTION "This is a list of numbers, where each number is encoded by one nibble, and interpeted as a signed integer. The nibbles correspond in order to the list define by Table 334 in IEEE Std 802.16-2004 starting from the second line, such that the LS nibble of the first byte corresponds to the second line in the table. The number encoded by each nibble represents the difference in normalized C/N relative to the previous line in the table" REFERENCE "Subclause 11.3.1.1, Table 357, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmaUcdBurstProfileEntry 4 } wmanIf2BsOfdmaUcdBurstProfileRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table. If the implementator of this MIB has choosen not to implement 'dynamic assignment' of profiles, this object is not useful and should return noSuchName upon SNMP request." ::= { wmanIf2BsOfdmaUcdBurstProfileEntry 5 } wmanIf2BsOfdmaDcdBurstProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2BsOfdmaDcdBurstProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each DCD burst profile. This table is double indexed. The primary index is an ifIndex with an ifType of propBWAp2Mp. The secondary index is wmanIf2BsOfdmaDiucIndex." ::= { wmanIf2BsOfdmaPhy 4 } wmanIf2BsOfdmaDcdBurstProfileEntry OBJECT-TYPE SYNTAX WmanIf2BsOfdmaDcdBurstProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each DCD burst profile. This table is double indexed. The primary index is an ifIndex with an ifType of propBWAp2Mp. The secondary index is wmanIf2BsOfdmaDiucIndex." INDEX { ifIndex, wmanIf2BsOfdmaDiucIndex } ::= { wmanIf2BsOfdmaDcdBurstProfileTable 1 } WmanIf2BsOfdmaDcdBurstProfileEntry ::= SEQUENCE { wmanIf2BsOfdmaDiucIndex INTEGER, wmanIf2BsOfdmaDownlinkFrequency Unsigned32, wmanIf2BsOfdmaDcdFecCodeType WmanIf2OfdmaFecCodeType, wmanIf2BsOfdmaDiucMandatoryExitThresh INTEGER, wmanIf2BsOfdmaDiucMinEntryThresh INTEGER, wmanIf2BsOfdmaDcdBurstProfileRowStatus RowStatus} wmanIf2BsOfdmaDiucIndex OBJECT-TYPE SYNTAX INTEGER (0 .. 12) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Downlink Interval Usage Code indicates the downlink burst profile in the DCD message, and is used along with ifIndex to identify an entry in the wmanIf2BsOfdmaDcdBurstProfileTable." REFERENCE "Subclause 8.4.5.3.1, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmaDcdBurstProfileEntry 1 } wmanIf2BsOfdmaDownlinkFrequency OBJECT-TYPE SYNTAX Unsigned32 UNITS "kHz" MAX-ACCESS read-create STATUS current DESCRIPTION "Downlink Frequency (kHz)." REFERENCE "Subclause 11.4.2, Table 359, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmaDcdBurstProfileEntry 2 } wmanIf2BsOfdmaDcdFecCodeType OBJECT-TYPE SYNTAX WmanIf2OfdmaFecCodeType MAX-ACCESS read-create STATUS current DESCRIPTION "Downlink FEC code type and modulation type" REFERENCE "Subclause 11.4.2, Table 363, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmaDcdBurstProfileEntry 3 } wmanIf2BsOfdmaDiucMandatoryExitThresh OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "DIUC mandatory exit threshold: 0 - 63.75 dB CINR at or below where this DIUC can no longer be used and where this change to a more robust DIUC is required, in 0.25 dB units." REFERENCE "Subclause 11.4.2, Table 363, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmaDcdBurstProfileEntry 4 } wmanIf2BsOfdmaDiucMinEntryThresh OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "DIUC minimum entry threshold: 0 - 63.75 dB The minimum CINR required to start using this DIUC when changing from a more robust DIUC is required, in 0.25 dB units." REFERENCE "Subclause 11.4.2, Table 363, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmaDcdBurstProfileEntry 5 } wmanIf2BsOfdmaDcdBurstProfileRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table. If the implementator of this MIB has choosen not to implement 'dynamic assignment' of profiles, this object is not useful and should return noSuchName upon SNMP request." ::= { wmanIf2BsOfdmaDcdBurstProfileEntry 6 } wmanIf2BsSsOfdmaReqCapabilitiesTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2BsSsOfdmaReqCapabilitiesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the basic capability information, specific to OFDMA Phy, of MSs that have been reported by MSs to BS using RNG-REQ, SBC-REQ and REG-REQ messages. Entries in this table should be created when an MS registers with a BS." ::= { wmanIf2BsOfdmaPhy 5 } wmanIf2BsSsOfdmaReqCapabilitiesEntry OBJECT-TYPE SYNTAX WmanIf2BsSsOfdmaReqCapabilitiesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each MS that has been registered in the BS. This table augments the table wmanIf2BsRegisteredSsTable." AUGMENTS { wmanIf2BsRegisteredSsEntry } ::= { wmanIf2BsSsOfdmaReqCapabilitiesTable 1 } WmanIf2BsSsOfdmaReqCapabilitiesEntry ::= SEQUENCE { wmanIf2BsSsOfdmaReqCapFftSizes WmanIf2OfdmaFftSizes, wmanIf2BsSsOfdmaReqCapDemodulator WmanIf2OfdmaMsDeModType, wmanIf2BsSsOfdmaReqCapModulator WmanIf2OfdmaMsModType, wmanIf2eBsSsOfdmaReqCapNoHarqChannel Unsigned32, wmanIf2BsSsOfdmaReqCapPermutation WmanIf2OfdmaPermutation, wmanIf2eBsSsOfdmaReqCapMobilityFeature WmanIf2eOfdmaMobility, wmanIf2eBsSsOfdmaReqCapMaxMacLevelDlFm WmanIf2eMaxMacLevel, wmanIf2eBsSsOfdmaReqCapMaxMacLevelUlFm WmanIf2eMaxMacLevel, wmanIf2eBsSsOfdmaReqCapDemMimo WmanIf2eOfdmaDemMimo, wmanIf2eBsSsOfdmaReqCapMimoCapability WmanIf2eOfdmaMimoCap, wmanIf2eBsSsOfdmaReqCapUlMimo WmanIf2eOfdmaUlMimo, wmanIf2eBsSsOfdmaReqCapPrivateMap WmanIf2eOfdmaPrivMap, wmanIf2eBsSsOfdmaReqCapAasCapability WmanIf2eOfdmaAasCap, wmanIf2eBsSsOfdmaReqCapCinrMesurement WmanIf2eOfdmaCinrCap, wmanIf2eBsSsOfdmaReqCapUlPowerControl WmanIf2eOfdmaUlPower, wmanIf2eBsSsOfdmaReqCapMapCapability WmanIf2eOfdmaMapCap, wmanIf2eBsSsOfdmaReqCapUlControlChannel WmanIf2eOfdmaUlCntlCh, wmanIf2eBsSsOfdmaReqCapCistCapability WmanIf2eOfdmaMsCistCap, wmanIf2eBsSsOfdmaReqCapMaxHarqBurst WmanIf2eOfdmaMaxHarq, wmanIf2eBsSsOfdmaReqCapModMimo WmanIf2eOfdmaModMimo, wmanIf2eBsSsOfdmaReqCapSdmaPilot WmanIf2eSdmaPilotCap, wmanIf2eBsSsOfdmaReqCapMultipleBurst WmanIf2eMultiBurst, wmanIf2eBsSsOfdmaReqCapIncrHarqBuffer WmanIf2eIncrHarqBuf, wmanIf2eBsSsOfdmaReqCapChaseHarqBuffer WmanIf2eChaseHarqBuf} wmanIf2BsSsOfdmaReqCapFftSizes OBJECT-TYPE SYNTAX WmanIf2OfdmaFftSizes MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the FFT sizes supported by MS." ::= { wmanIf2BsSsOfdmaReqCapabilitiesEntry 1 } wmanIf2BsSsOfdmaReqCapDemodulator OBJECT-TYPE SYNTAX WmanIf2OfdmaMsDeModType MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the different demodulator options supported by MS for downlink." ::= { wmanIf2BsSsOfdmaReqCapabilitiesEntry 2 } wmanIf2BsSsOfdmaReqCapModulator OBJECT-TYPE SYNTAX WmanIf2OfdmaMsModType MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the different modulator options supported by MS for uplink." ::= { wmanIf2BsSsOfdmaReqCapabilitiesEntry 3 } wmanIf2eBsSsOfdmaReqCapNoHarqChannel OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This field specifies the number of uplink H-ARQ channels (n) the SS supports, where n = 1..16. The value of this object should be 0..15." ::= { wmanIf2BsSsOfdmaReqCapabilitiesEntry 4 } wmanIf2BsSsOfdmaReqCapPermutation OBJECT-TYPE SYNTAX WmanIf2OfdmaPermutation MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the OFDMA MS Permutation support." ::= { wmanIf2BsSsOfdmaReqCapabilitiesEntry 5 } wmanIf2eBsSsOfdmaReqCapMobilityFeature OBJECT-TYPE SYNTAX WmanIf2eOfdmaMobility MAX-ACCESS read-only STATUS current DESCRIPTION "The field indicates whether or not the MS supports mobility hand-over, Sleepmode, and Idle-mode." ::= { wmanIf2BsSsOfdmaReqCapabilitiesEntry 6 } wmanIf2eBsSsOfdmaReqCapMaxMacLevelDlFm OBJECT-TYPE SYNTAX WmanIf2eMaxMacLevel MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum amount of MAC level data the MS is capable of processing per DL frame." REFERENCE "Subclause 11.7.8.10.1 in IEEE Std 802.16e-2005" DEFVAL { 0 } ::= { wmanIf2BsSsOfdmaReqCapabilitiesEntry 7 } wmanIf2eBsSsOfdmaReqCapMaxMacLevelUlFm OBJECT-TYPE SYNTAX WmanIf2eMaxMacLevel MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum amount of MAC level data the MS is capable of processing per UL frame." REFERENCE "Subclause 11.7.8.10.1 in IEEE Std 802.16e-2005" DEFVAL { 0 } ::= { wmanIf2BsSsOfdmaReqCapabilitiesEntry 8 } wmanIf2eBsSsOfdmaReqCapDemMimo OBJECT-TYPE SYNTAX WmanIf2eOfdmaDemMimo MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the different MIMO options supported by a WirelessMAN-OFDMA PHY SS in the downlink." ::= { wmanIf2BsSsOfdmaReqCapabilitiesEntry 9 } wmanIf2eBsSsOfdmaReqCapMimoCapability OBJECT-TYPE SYNTAX WmanIf2eOfdmaMimoCap MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the MIMO capability of OFDMA MS demodulator." ::= { wmanIf2BsSsOfdmaReqCapabilitiesEntry 10 } wmanIf2eBsSsOfdmaReqCapUlMimo OBJECT-TYPE SYNTAX WmanIf2eOfdmaUlMimo MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates different MIMO options supported by a OFDMA PHY SS in the uplink" REFERENCE "Subclause 11.8.3.7.6 in IEEE 802.16e" ::= { wmanIf2BsSsOfdmaReqCapabilitiesEntry 11 } wmanIf2eBsSsOfdmaReqCapPrivateMap OBJECT-TYPE SYNTAX WmanIf2eOfdmaPrivMap MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates AAS private map parameters supported by a OFDMA SS" REFERENCE "Subclause 11.8.3.7.7 in IEEE 802.16e" ::= { wmanIf2BsSsOfdmaReqCapabilitiesEntry 12 } wmanIf2eBsSsOfdmaReqCapAasCapability OBJECT-TYPE SYNTAX WmanIf2eOfdmaAasCap MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates different AAS options supported by a OFDMA PHY SS in the downlink" REFERENCE "Subclause 11.8.3.7.8 in IEEE 802.16e" ::= { wmanIf2BsSsOfdmaReqCapabilitiesEntry 13 } wmanIf2eBsSsOfdmaReqCapCinrMesurement OBJECT-TYPE SYNTAX WmanIf2eOfdmaCinrCap MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the CINR measurement capability supported by a OFDMA PHY SS in the downlink." REFERENCE "Subclause 11.8.3.7.9 in IEEE 802.16e" ::= { wmanIf2BsSsOfdmaReqCapabilitiesEntry 14 } wmanIf2eBsSsOfdmaReqCapUlPowerControl OBJECT-TYPE SYNTAX WmanIf2eOfdmaUlPower MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the power control options supported by a OFDMA PHY SS for uplink transmission." REFERENCE "Subclause 11.8.3.7.11 in IEEE 802.16e" ::= { wmanIf2BsSsOfdmaReqCapabilitiesEntry 15 } wmanIf2eBsSsOfdmaReqCapMapCapability OBJECT-TYPE SYNTAX WmanIf2eOfdmaMapCap MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the different MAP options supported by a OFDMA PHY SS" REFERENCE "Subclause 11.8.3.7.11 in IEEE 802.16e" ::= { wmanIf2BsSsOfdmaReqCapabilitiesEntry 16 } wmanIf2eBsSsOfdmaReqCapUlControlChannel OBJECT-TYPE SYNTAX WmanIf2eOfdmaUlCntlCh MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the different uplink control channels supported by a OFDMA PHY SS." REFERENCE "Subclause 11.8.3.7.13 in IEEE 802.16e" ::= { wmanIf2BsSsOfdmaReqCapabilitiesEntry 17 } wmanIf2eBsSsOfdmaReqCapCistCapability OBJECT-TYPE SYNTAX WmanIf2eOfdmaMsCistCap MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the MS capability of supporting CSIT (uplink sounding)." REFERENCE "Subclause 11.8.3.7.14 in IEEE 802.16e" ::= { wmanIf2BsSsOfdmaReqCapabilitiesEntry 18 } wmanIf2eBsSsOfdmaReqCapMaxHarqBurst OBJECT-TYPE SYNTAX WmanIf2eOfdmaMaxHarq MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the maximum number of UL/DL HARQ burst allocations for the SS in a single UL/DL subframe." REFERENCE "Subclause 11.8.3.7.15 in IEEE 802.16e" ::= { wmanIf2BsSsOfdmaReqCapabilitiesEntry 19 } wmanIf2eBsSsOfdmaReqCapModMimo OBJECT-TYPE SYNTAX WmanIf2eOfdmaModMimo MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the MIMO capability of OFDMA SS modulator." REFERENCE "Subclause 11.8.3.7.16 in IEEE 802.16e" ::= { wmanIf2BsSsOfdmaReqCapabilitiesEntry 20 } wmanIf2eBsSsOfdmaReqCapSdmaPilot OBJECT-TYPE SYNTAX WmanIf2eSdmaPilotCap MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the SDMA pilot pattern support for AMC zone." REFERENCE "Subclause 11.8.3.7.17 in IEEE 802.16e" ::= { wmanIf2BsSsOfdmaReqCapabilitiesEntry 21 } wmanIf2eBsSsOfdmaReqCapMultipleBurst OBJECT-TYPE SYNTAX WmanIf2eMultiBurst MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates whether multiple FEC types are supported in DL/UL burst profiles." REFERENCE "Subclause 11.8.3.7.18 in IEEE 802.16e" ::= { wmanIf2BsSsOfdmaReqCapabilitiesEntry 22 } wmanIf2eBsSsOfdmaReqCapIncrHarqBuffer OBJECT-TYPE SYNTAX WmanIf2eIncrHarqBuf MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the maximal number of data bits the SS is able to use for buffering for NEP/NSCH based incremental redundancy CTC in downlink and uplink transmissions." REFERENCE "Subclause 11.8.3.7.19 in IEEE 802.16e" ::= { wmanIf2BsSsOfdmaReqCapabilitiesEntry 23 } wmanIf2eBsSsOfdmaReqCapChaseHarqBuffer OBJECT-TYPE SYNTAX WmanIf2eChaseHarqBuf MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the maximal number of data bits the SS is able to use for buffering for DIUC/duration based HARQ methods (Chase combining and CC-IR)in downlink and uplink transmissions." REFERENCE "Subclause 11.8.3.7.19 in IEEE 802.16e" ::= { wmanIf2BsSsOfdmaReqCapabilitiesEntry 24 } wmanIf2BsSsOfdmaRspCapabilitiesTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2BsSsOfdmaRspCapabilitiesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the basic capability information, specific to OFDMA Phy, of MSs that have been reported by MSs to BS using RNG-REQ, SBC-REQ and REG-REQ messages. Entries in this table should be created when an MS registers with a BS." ::= { wmanIf2BsOfdmaPhy 6 } wmanIf2BsSsOfdmaRspCapabilitiesEntry OBJECT-TYPE SYNTAX WmanIf2BsSsOfdmaRspCapabilitiesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each MS that has been registered in the BS. This table augments the table wmanIf2BsRegisteredSsTable." AUGMENTS { wmanIf2BsRegisteredSsEntry } ::= { wmanIf2BsSsOfdmaRspCapabilitiesTable 1 } WmanIf2BsSsOfdmaRspCapabilitiesEntry ::= SEQUENCE { wmanIf2BsSsOfdmaRspCapFftSizes WmanIf2OfdmaFftSizes, wmanIf2BsSsOfdmaRspCapDemodulator WmanIf2OfdmaMsDeModType, wmanIf2BsSsOfdmaRspCapModulator WmanIf2OfdmaMsModType, wmanIf2BsSsOfdmaRspCapNoHarqChannel Unsigned32, wmanIf2BsSsOfdmaRspCapPermutation WmanIf2OfdmaPermutation, wmanIf2eBsSsOfdmaRspCapMobilityFeature WmanIf2eOfdmaMobility, wmanIf2eBsSsOfdmaRspCapMaxMacLevelDlFm WmanIf2eMaxMacLevel, wmanIf2eBsSsOfdmaRspCapMaxMacLevelUlFm WmanIf2eMaxMacLevel, wmanIf2eBsSsOfdmaRspCapDemMimo WmanIf2eOfdmaDemMimo, wmanIf2eBsSsOfdmaRspCapMimoCapability WmanIf2eOfdmaMimoCap, wmanIf2eBsSsOfdmaRspCapUlMimo WmanIf2eOfdmaUlMimo, wmanIf2eBsSsOfdmaRspCapPrivateMap WmanIf2eOfdmaPrivMap, wmanIf2eBsSsOfdmaRspCapAasCapability WmanIf2eOfdmaAasCap, wmanIf2eBsSsOfdmaRspCapCinrMesurement WmanIf2eOfdmaCinrCap, wmanIf2eBsSsOfdmaRspCapUlPowerControl WmanIf2eOfdmaUlPower, wmanIf2eBsSsOfdmaRspCapMapCapability WmanIf2eOfdmaMapCap, wmanIf2eBsSsOfdmaRspCapUlControlChannel WmanIf2eOfdmaUlCntlCh, wmanIf2eBsSsOfdmaRspCapCistCapability WmanIf2eOfdmaMsCistCap, wmanIf2eBsSsOfdmaRspCapMaxHarqBurst WmanIf2eOfdmaMaxHarq, wmanIf2eBsSsOfdmaRspCapModMimo WmanIf2eOfdmaModMimo, wmanIf2eBsSsOfdmaRspCapSdmaPilot WmanIf2eSdmaPilotCap, wmanIf2eBsSsOfdmaRspCapMultipleBurst WmanIf2eMultiBurst, wmanIf2eBsSsOfdmaRspCapIncrHarqBuffer WmanIf2eIncrHarqBuf, wmanIf2eBsSsOfdmaRspCapChaseHarqBuffer WmanIf2eChaseHarqBuf} wmanIf2BsSsOfdmaRspCapFftSizes OBJECT-TYPE SYNTAX WmanIf2OfdmaFftSizes MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the FFT sizes negotiated with the MS." ::= { wmanIf2BsSsOfdmaRspCapabilitiesEntry 1 } wmanIf2BsSsOfdmaRspCapDemodulator OBJECT-TYPE SYNTAX WmanIf2OfdmaMsDeModType MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the different demodulator options negotiated for MS for downlink." ::= { wmanIf2BsSsOfdmaRspCapabilitiesEntry 2 } wmanIf2BsSsOfdmaRspCapModulator OBJECT-TYPE SYNTAX WmanIf2OfdmaMsModType MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the different modulator options negotiated for MS for uplink." ::= { wmanIf2BsSsOfdmaRspCapabilitiesEntry 3 } wmanIf2BsSsOfdmaRspCapNoHarqChannel OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This field specifies the number of uplink H-ARQ channels (n) the SS supports, where n = 1..16. The value of this object should be 0..15." ::= { wmanIf2BsSsOfdmaRspCapabilitiesEntry 4 } wmanIf2BsSsOfdmaRspCapPermutation OBJECT-TYPE SYNTAX WmanIf2OfdmaPermutation MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the OFDMA MS Permutation support negotiated for MS." ::= { wmanIf2BsSsOfdmaRspCapabilitiesEntry 5 } wmanIf2eBsSsOfdmaRspCapMobilityFeature OBJECT-TYPE SYNTAX WmanIf2eOfdmaMobility MAX-ACCESS read-only STATUS current DESCRIPTION "The field indicates the mobility hand-over, Sleepmode, and Idle-mode negotiated for MS." ::= { wmanIf2BsSsOfdmaRspCapabilitiesEntry 6 } wmanIf2eBsSsOfdmaRspCapMaxMacLevelDlFm OBJECT-TYPE SYNTAX WmanIf2eMaxMacLevel MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum amount of MAC level data the MS is capable of processing per DL frame. A value of 0 indicates such limitation does not exist, except the limitation of the physical medium" REFERENCE "Subclause 11.7.8.10.1 in IEEE Std 802.16e-2005" DEFVAL { 0 } ::= { wmanIf2BsSsOfdmaRspCapabilitiesEntry 7 } wmanIf2eBsSsOfdmaRspCapMaxMacLevelUlFm OBJECT-TYPE SYNTAX WmanIf2eMaxMacLevel MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum amount of MAC level data the MS is capable of processing per UL frame. A value of 0 indicates such limitation does not exist, except the limitation of the physical medium" REFERENCE "Subclause 11.7.8.10.1 in IEEE Std 802.16e-2005" DEFVAL { 0 } ::= { wmanIf2BsSsOfdmaRspCapabilitiesEntry 8 } wmanIf2eBsSsOfdmaRspCapDemMimo OBJECT-TYPE SYNTAX WmanIf2eOfdmaDemMimo MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the different MIMO options supported by a WirelessMAN-OFDMA PHY SS in the downlink." ::= { wmanIf2BsSsOfdmaRspCapabilitiesEntry 9 } wmanIf2eBsSsOfdmaRspCapMimoCapability OBJECT-TYPE SYNTAX WmanIf2eOfdmaMimoCap MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the MIMO capability of OFDMA MS demodulator." ::= { wmanIf2BsSsOfdmaRspCapabilitiesEntry 10 } wmanIf2eBsSsOfdmaRspCapUlMimo OBJECT-TYPE SYNTAX WmanIf2eOfdmaUlMimo MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates different MIMO options supported by a OFDMA PHY SS in the uplink" REFERENCE "Subclause 11.8.3.7.6 in IEEE 802.16e" ::= { wmanIf2BsSsOfdmaRspCapabilitiesEntry 11 } wmanIf2eBsSsOfdmaRspCapPrivateMap OBJECT-TYPE SYNTAX WmanIf2eOfdmaPrivMap MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates AAS private map parameters supported by a OFDMA SS" REFERENCE "Subclause 11.8.3.7.7 in IEEE 802.16e" ::= { wmanIf2BsSsOfdmaRspCapabilitiesEntry 12 } wmanIf2eBsSsOfdmaRspCapAasCapability OBJECT-TYPE SYNTAX WmanIf2eOfdmaAasCap MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates different AAS options supported by a OFDMA PHY SS in the downlink" REFERENCE "Subclause 11.8.3.7.8 in IEEE 802.16e" ::= { wmanIf2BsSsOfdmaRspCapabilitiesEntry 13 } wmanIf2eBsSsOfdmaRspCapCinrMesurement OBJECT-TYPE SYNTAX WmanIf2eOfdmaCinrCap MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the CINR measurement capability supported by a OFDMA PHY SS in the downlink." REFERENCE "Subclause 11.8.3.7.9 in IEEE 802.16e" ::= { wmanIf2BsSsOfdmaRspCapabilitiesEntry 14 } wmanIf2eBsSsOfdmaRspCapUlPowerControl OBJECT-TYPE SYNTAX WmanIf2eOfdmaUlPower MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the power control options supported by a OFDMA PHY SS for uplink transmission." REFERENCE "Subclause 11.8.3.7.11 in IEEE 802.16e" ::= { wmanIf2BsSsOfdmaRspCapabilitiesEntry 15 } wmanIf2eBsSsOfdmaRspCapMapCapability OBJECT-TYPE SYNTAX WmanIf2eOfdmaMapCap MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the different MAP options supported by a OFDMA PHY SS" REFERENCE "Subclause 11.8.3.7.11 in IEEE 802.16e" ::= { wmanIf2BsSsOfdmaRspCapabilitiesEntry 16 } wmanIf2eBsSsOfdmaRspCapUlControlChannel OBJECT-TYPE SYNTAX WmanIf2eOfdmaUlCntlCh MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the different uplink control channels supported by a OFDMA PHY SS." REFERENCE "Subclause 11.8.3.7.13 in IEEE 802.16e" ::= { wmanIf2BsSsOfdmaRspCapabilitiesEntry 17 } wmanIf2eBsSsOfdmaRspCapCistCapability OBJECT-TYPE SYNTAX WmanIf2eOfdmaMsCistCap MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the MS capability of supporting CSIT (uplink sounding)." REFERENCE "Subclause 11.8.3.7.14 in IEEE 802.16e" ::= { wmanIf2BsSsOfdmaRspCapabilitiesEntry 18 } wmanIf2eBsSsOfdmaRspCapMaxHarqBurst OBJECT-TYPE SYNTAX WmanIf2eOfdmaMaxHarq MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the maximum number of UL/DL HARQ burst allocations for the SS in a single UL/DL subframe." REFERENCE "Subclause 11.8.3.7.15 in IEEE 802.16e" ::= { wmanIf2BsSsOfdmaRspCapabilitiesEntry 19 } wmanIf2eBsSsOfdmaRspCapModMimo OBJECT-TYPE SYNTAX WmanIf2eOfdmaModMimo MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the MIMO capability of OFDMA SS modulator." REFERENCE "Subclause 11.8.3.7.16 in IEEE 802.16e" ::= { wmanIf2BsSsOfdmaRspCapabilitiesEntry 20 } wmanIf2eBsSsOfdmaRspCapSdmaPilot OBJECT-TYPE SYNTAX WmanIf2eSdmaPilotCap MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the SDMA pilot pattern support for AMC zone." REFERENCE "Subclause 11.8.3.7.17 in IEEE 802.16e" ::= { wmanIf2BsSsOfdmaRspCapabilitiesEntry 21 } wmanIf2eBsSsOfdmaRspCapMultipleBurst OBJECT-TYPE SYNTAX WmanIf2eMultiBurst MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates whether multiple FEC types are supported in DL/UL burst profiles." REFERENCE "Subclause 11.8.3.7.18 in IEEE 802.16e" ::= { wmanIf2BsSsOfdmaRspCapabilitiesEntry 22 } wmanIf2eBsSsOfdmaRspCapIncrHarqBuffer OBJECT-TYPE SYNTAX WmanIf2eIncrHarqBuf MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the maximal number of data bits the SS is able to use for buffering for NEP/NSCH based incremental redundancy CTC in downlink and uplink transmissions." REFERENCE "Subclause 11.8.3.7.19 in IEEE 802.16e" ::= { wmanIf2BsSsOfdmaRspCapabilitiesEntry 23 } wmanIf2eBsSsOfdmaRspCapChaseHarqBuffer OBJECT-TYPE SYNTAX WmanIf2eChaseHarqBuf MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the maximal number of data bits the SS is able to use for buffering for DIUC/duration based HARQ methods (Chase combining and CC-IR)in downlink and uplink transmissions." REFERENCE "Subclause 11.8.3.7.19 in IEEE 802.16e" ::= { wmanIf2BsSsOfdmaRspCapabilitiesEntry 24 } wmanIf2BsOfdmaCapabilitiesTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2BsOfdmaCapabilitiesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the basic capabilities, specific to OFDMA Phy, of the BS as implemented in BS hardware and software. These capabilities along with the configuration for them (wmanIf2BsOfdmaCapabilitiesConfigTable) are used for negotiation of basic capabilities with SS using RNG-RSP, SBC-RSP and REG-RSP messages. The negotiated capabilities are obtained by interSubclause of MS raw reported capabilities, BS raw capabilities and BS configured capabilities. The objects in the table have read-only access. The table is maintained by BS." ::= { wmanIf2BsOfdmaPhy 7 } wmanIf2BsOfdmaCapabilitiesEntry OBJECT-TYPE SYNTAX WmanIf2BsOfdmaCapabilitiesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each BS sector and is indexed by ifIndex." INDEX { ifIndex } ::= { wmanIf2BsOfdmaCapabilitiesTable 1 } WmanIf2BsOfdmaCapabilitiesEntry ::= SEQUENCE { wmanIf2BsOfdmaCapFftSizes WmanIf2OfdmaFftSizes, wmanIf2BsOfdmaCapDemodulator WmanIf2OfdmaMsDeModType, wmanIf2BsOfdmaCapModulator WmanIf2OfdmaMsModType, wmanIf2BsOfdmaCapNoHarqChannel Unsigned32, wmanIf2BsOfdmaCapPermutation WmanIf2OfdmaPermutation, wmanIf2eBsOfdmaCapMobilityFeature WmanIf2eOfdmaMobility, wmanIf2eBsSsOfdmaCapMaxMacLevelDlFm WmanIf2eMaxMacLevel, wmanIf2eBsSsOfdmaCapMaxMacLevelUlFm WmanIf2eMaxMacLevel, wmanIf2eBsSsOfdmaCapDemMimo WmanIf2eOfdmaDemMimo, wmanIf2eBsSsOfdmaCapMimoCapability WmanIf2eOfdmaMimoCap, wmanIf2eBsSsOfdmaCapUlMimo WmanIf2eOfdmaUlMimo, wmanIf2eBsSsOfdmaCapPrivateMap WmanIf2eOfdmaPrivMap, wmanIf2eBsSsOfdmaCapAasCapability WmanIf2eOfdmaAasCap, wmanIf2eBsSsOfdmaCapCinrMesurement WmanIf2eOfdmaCinrCap, wmanIf2eBsSsOfdmaCapUlPowerControl WmanIf2eOfdmaUlPower, wmanIf2eBsSsOfdmaCapMapCapability WmanIf2eOfdmaMapCap, wmanIf2eBsSsOfdmaCapUlControlChannel WmanIf2eOfdmaUlCntlCh, wmanIf2eBsSsOfdmaCapCistCapability WmanIf2eOfdmaMsCistCap, wmanIf2eBsSsOfdmaCapMaxHarqBurst WmanIf2eOfdmaMaxHarq, wmanIf2eBsSsOfdmaCapModMimo WmanIf2eOfdmaModMimo, wmanIf2eBsSsOfdmaCapSdmaPilot WmanIf2eSdmaPilotCap, wmanIf2eBsSsOfdmaCapMultipleBurst WmanIf2eMultiBurst, wmanIf2eBsSsOfdmaCapIncrHarqBuffer WmanIf2eIncrHarqBuf, wmanIf2eBsSsOfdmaCapChaseHarqBuffer WmanIf2eChaseHarqBuf} wmanIf2BsOfdmaCapFftSizes OBJECT-TYPE SYNTAX WmanIf2OfdmaFftSizes MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the FFT sizes supported by BS." ::= { wmanIf2BsOfdmaCapabilitiesEntry 1 } wmanIf2BsOfdmaCapDemodulator OBJECT-TYPE SYNTAX WmanIf2OfdmaMsDeModType MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the different demodulator options supported by BS." ::= { wmanIf2BsOfdmaCapabilitiesEntry 2 } wmanIf2BsOfdmaCapModulator OBJECT-TYPE SYNTAX WmanIf2OfdmaMsModType MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the different modulator options supported by BS." ::= { wmanIf2BsOfdmaCapabilitiesEntry 3 } wmanIf2BsOfdmaCapNoHarqChannel OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This field specifies the number of uplink H-ARQ channels (n) the SS supports, where n = 1..16. The value of this object should be 0..15." ::= { wmanIf2BsOfdmaCapabilitiesEntry 4 } wmanIf2BsOfdmaCapPermutation OBJECT-TYPE SYNTAX WmanIf2OfdmaPermutation MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the OFDMA MS Permutation support supported by BS." ::= { wmanIf2BsOfdmaCapabilitiesEntry 5 } wmanIf2eBsOfdmaCapMobilityFeature OBJECT-TYPE SYNTAX WmanIf2eOfdmaMobility MAX-ACCESS read-only STATUS current DESCRIPTION "The field indicates the mobility hand-over, Sleepmode, and Idle-mode supported by BS." ::= { wmanIf2BsOfdmaCapabilitiesEntry 6 } wmanIf2eBsSsOfdmaCapMaxMacLevelDlFm OBJECT-TYPE SYNTAX WmanIf2eMaxMacLevel MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum amount of MAC level data the MS is capable of processing per DL frame. A value of 0 indicates such limitation does not exist, except the limitation of the physical medium" REFERENCE "Subclause 11.7.8.10.1 in IEEE Std 802.16e-2005" DEFVAL { 0 } ::= { wmanIf2BsOfdmaCapabilitiesEntry 7 } wmanIf2eBsSsOfdmaCapMaxMacLevelUlFm OBJECT-TYPE SYNTAX WmanIf2eMaxMacLevel MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum amount of MAC level data the MS is capable of processing per UL frame. A value of 0 indicates such limitation does not exist, except the limitation of the physical medium" REFERENCE "Subclause 11.7.8.10.1 in IEEE Std 802.16e-2005" DEFVAL { 0 } ::= { wmanIf2BsOfdmaCapabilitiesEntry 8 } wmanIf2eBsSsOfdmaCapDemMimo OBJECT-TYPE SYNTAX WmanIf2eOfdmaDemMimo MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the different MIMO options supported by a WirelessMAN-OFDMA PHY SS in the downlink." ::= { wmanIf2BsOfdmaCapabilitiesEntry 9 } wmanIf2eBsSsOfdmaCapMimoCapability OBJECT-TYPE SYNTAX WmanIf2eOfdmaMimoCap MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the MIMO capability of OFDMA MS demodulator." ::= { wmanIf2BsOfdmaCapabilitiesEntry 10 } wmanIf2eBsSsOfdmaCapUlMimo OBJECT-TYPE SYNTAX WmanIf2eOfdmaUlMimo MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates different MIMO options supported by a OFDMA PHY SS in the uplink" REFERENCE "Subclause 11.8.3.7.6 in IEEE 802.16e" ::= { wmanIf2BsOfdmaCapabilitiesEntry 11 } wmanIf2eBsSsOfdmaCapPrivateMap OBJECT-TYPE SYNTAX WmanIf2eOfdmaPrivMap MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates AAS private map parameters supported by a OFDMA SS" REFERENCE "Subclause 11.8.3.7.7 in IEEE 802.16e" ::= { wmanIf2BsOfdmaCapabilitiesEntry 12 } wmanIf2eBsSsOfdmaCapAasCapability OBJECT-TYPE SYNTAX WmanIf2eOfdmaAasCap MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates different AAS options supported by a OFDMA PHY SS in the downlink" REFERENCE "Subclause 11.8.3.7.8 in IEEE 802.16e" ::= { wmanIf2BsOfdmaCapabilitiesEntry 13 } wmanIf2eBsSsOfdmaCapCinrMesurement OBJECT-TYPE SYNTAX WmanIf2eOfdmaCinrCap MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the CINR measurement capability supported by a OFDMA PHY SS in the downlink." REFERENCE "Subclause 11.8.3.7.9 in IEEE 802.16e" ::= { wmanIf2BsOfdmaCapabilitiesEntry 14 } wmanIf2eBsSsOfdmaCapUlPowerControl OBJECT-TYPE SYNTAX WmanIf2eOfdmaUlPower MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the power control options supported by a OFDMA PHY SS for uplink transmission." REFERENCE "Subclause 11.8.3.7.11 in IEEE 802.16e" ::= { wmanIf2BsOfdmaCapabilitiesEntry 15 } wmanIf2eBsSsOfdmaCapMapCapability OBJECT-TYPE SYNTAX WmanIf2eOfdmaMapCap MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the different MAP options supported by a OFDMA PHY SS" REFERENCE "Subclause 11.8.3.7.11 in IEEE 802.16e" ::= { wmanIf2BsOfdmaCapabilitiesEntry 16 } wmanIf2eBsSsOfdmaCapUlControlChannel OBJECT-TYPE SYNTAX WmanIf2eOfdmaUlCntlCh MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the different uplink control channels supported by a OFDMA PHY SS." REFERENCE "Subclause 11.8.3.7.13 in IEEE 802.16e" ::= { wmanIf2BsOfdmaCapabilitiesEntry 17 } wmanIf2eBsSsOfdmaCapCistCapability OBJECT-TYPE SYNTAX WmanIf2eOfdmaMsCistCap MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the MS capability of supporting CSIT (uplink sounding)." REFERENCE "Subclause 11.8.3.7.14 in IEEE 802.16e" ::= { wmanIf2BsOfdmaCapabilitiesEntry 18 } wmanIf2eBsSsOfdmaCapMaxHarqBurst OBJECT-TYPE SYNTAX WmanIf2eOfdmaMaxHarq MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the maximum number of UL/DL HARQ burst allocations for the SS in a single UL/DL subframe." REFERENCE "Subclause 11.8.3.7.15 in IEEE 802.16e" ::= { wmanIf2BsOfdmaCapabilitiesEntry 19 } wmanIf2eBsSsOfdmaCapModMimo OBJECT-TYPE SYNTAX WmanIf2eOfdmaModMimo MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the MIMO capability of OFDMA SS modulator." REFERENCE "Subclause 11.8.3.7.16 in IEEE 802.16e" ::= { wmanIf2BsOfdmaCapabilitiesEntry 20 } wmanIf2eBsSsOfdmaCapSdmaPilot OBJECT-TYPE SYNTAX WmanIf2eSdmaPilotCap MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the SDMA pilot pattern support for AMC zone." REFERENCE "Subclause 11.8.3.7.17 in IEEE 802.16e" ::= { wmanIf2BsOfdmaCapabilitiesEntry 21 } wmanIf2eBsSsOfdmaCapMultipleBurst OBJECT-TYPE SYNTAX WmanIf2eMultiBurst MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates whether multiple FEC types are supported in DL/UL burst profiles." REFERENCE "Subclause 11.8.3.7.18 in IEEE 802.16e" ::= { wmanIf2BsOfdmaCapabilitiesEntry 22 } wmanIf2eBsSsOfdmaCapIncrHarqBuffer OBJECT-TYPE SYNTAX WmanIf2eIncrHarqBuf MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the maximal number of data bits the SS is able to use for buffering for NEP/NSCH based incremental redundancy CTC in downlink and uplink transmissions." REFERENCE "Subclause 11.8.3.7.19 in IEEE 802.16e" ::= { wmanIf2BsOfdmaCapabilitiesEntry 23 } wmanIf2eBsSsOfdmaCapChaseHarqBuffer OBJECT-TYPE SYNTAX WmanIf2eChaseHarqBuf MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the maximal number of data bits the SS is able to use for buffering for DIUC/duration based HARQ methods (Chase combining and CC-IR)in downlink and uplink transmissions." REFERENCE "Subclause 11.8.3.7.19 in IEEE 802.16e" ::= { wmanIf2BsOfdmaCapabilitiesEntry 24 } wmanIf2BsOfdmaCapabilitiesConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2BsOfdmaCapabilitiesConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the configuration for basic capabilities of BS, specific to OFDMA Phy. The table is intended to be used to restrict the Capabilities implemented by BS, for example in order to comply with local regulatory requirements. The BS should use the configuration along with the implemented Capabilities (wmanIf2BsOfdmaPhyTable) for negotiation of basic capabilities with SS using RNG-RSP, SBC-RSP and REG-RSP messages. The negotiated capabilities are obtained by interSubclause of MS reported capabilities, BS raw capabilities and BS configured capabilities. The objects in the table have read-write access. The rows are created by BS as a copy of wmanIf2BsBasicCapabilitiesTable and can be modified by NMS." ::= { wmanIf2BsOfdmaPhy 8 } wmanIf2BsOfdmaCapabilitiesConfigEntry OBJECT-TYPE SYNTAX WmanIf2BsOfdmaCapabilitiesConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each BS sector and is indexed by ifIndex." INDEX { ifIndex } ::= { wmanIf2BsOfdmaCapabilitiesConfigTable 1 } WmanIf2BsOfdmaCapabilitiesConfigEntry ::= SEQUENCE { wmanIf2BsOfdmaCapCfgFftSizes WmanIf2OfdmaFftSizes, wmanIf2BsOfdmaCapCfgDemodulator WmanIf2OfdmaMsDeModType, wmanIf2BsOfdmaCapCfgModulator WmanIf2OfdmaMsModType, wmanIf2BsOfdmaCapCfgNoHarqChannel Unsigned32, wmanIf2BsOfdmaCapCfgPermutation WmanIf2OfdmaPermutation, wmanIf2eBsOfdmaCapCfgMobilityFeature WmanIf2eOfdmaMobility, wmanIf2eBsSsOfdmaCapCfgMaxMacLevelDlFm WmanIf2eMaxMacLevel, wmanIf2eBsSsOfdmaCapCfgMaxMacLevelUlFm WmanIf2eMaxMacLevel, wmanIf2eBsSsOfdmaCapCfgDemMimo WmanIf2eOfdmaDemMimo, wmanIf2eBsSsOfdmaCapCfgMimoCapability WmanIf2eOfdmaMimoCap, wmanIf2eBsSsOfdmaCapCfgUlMimo WmanIf2eOfdmaUlMimo, wmanIf2eBsSsOfdmaCapCfgPrivateMap WmanIf2eOfdmaPrivMap, wmanIf2eBsSsOfdmaCapCfgAasCapability WmanIf2eOfdmaAasCap, wmanIf2eBsSsOfdmaCapCfgCinrMesurement WmanIf2eOfdmaCinrCap, wmanIf2eBsSsOfdmaCapCfgUlPowerControl WmanIf2eOfdmaUlPower, wmanIf2eBsSsOfdmaCapCfgMapCapability WmanIf2eOfdmaMapCap, wmanIf2eBsSsOfdmaCapCfgUlControlChannel WmanIf2eOfdmaUlCntlCh, wmanIf2eBsSsOfdmaCapCfgCistCapability WmanIf2eOfdmaMsCistCap, wmanIf2eBsSsOfdmaCapCfgMaxHarqBurst WmanIf2eOfdmaMaxHarq, wmanIf2eBsSsOfdmaCapCfgModMimo WmanIf2eOfdmaModMimo, wmanIf2eBsSsOfdmaCapCfgSdmaPilot WmanIf2eSdmaPilotCap, wmanIf2eBsSsOfdmaCapCfgMultipleBurst WmanIf2eMultiBurst, wmanIf2eBsSsOfdmaCapCfgIncrHarqBuffer WmanIf2eIncrHarqBuf, wmanIf2eBsSsOfdmaCapCfgChaseHarqBuffer WmanIf2eChaseHarqBuf} wmanIf2BsOfdmaCapCfgFftSizes OBJECT-TYPE SYNTAX WmanIf2OfdmaFftSizes MAX-ACCESS read-write STATUS current DESCRIPTION "This field indicates the FFT sizes configured for the BS." ::= { wmanIf2BsOfdmaCapabilitiesConfigEntry 1 } wmanIf2BsOfdmaCapCfgDemodulator OBJECT-TYPE SYNTAX WmanIf2OfdmaMsDeModType MAX-ACCESS read-write STATUS current DESCRIPTION "This field indicates the different demodulator options configured for the BS." ::= { wmanIf2BsOfdmaCapabilitiesConfigEntry 2 } wmanIf2BsOfdmaCapCfgModulator OBJECT-TYPE SYNTAX WmanIf2OfdmaMsModType MAX-ACCESS read-write STATUS current DESCRIPTION "This field indicates the different modulator options configured for the BS." ::= { wmanIf2BsOfdmaCapabilitiesConfigEntry 3 } wmanIf2BsOfdmaCapCfgNoHarqChannel OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This field specifies the number of uplink H-ARQ channels (n) the SS supports, where n = 1..16. The value of this object should be 0..15." ::= { wmanIf2BsOfdmaCapabilitiesConfigEntry 4 } wmanIf2BsOfdmaCapCfgPermutation OBJECT-TYPE SYNTAX WmanIf2OfdmaPermutation MAX-ACCESS read-write STATUS current DESCRIPTION "This field indicates the OFDMA MS Permutation support configured for the BS." ::= { wmanIf2BsOfdmaCapabilitiesConfigEntry 5 } wmanIf2eBsOfdmaCapCfgMobilityFeature OBJECT-TYPE SYNTAX WmanIf2eOfdmaMobility MAX-ACCESS read-write STATUS current DESCRIPTION "The field indicates the mobility hand-over, Sleepmode, and Idle-mode configured for the BS." ::= { wmanIf2BsOfdmaCapabilitiesConfigEntry 6 } wmanIf2eBsSsOfdmaCapCfgMaxMacLevelDlFm OBJECT-TYPE SYNTAX WmanIf2eMaxMacLevel MAX-ACCESS read-write STATUS current DESCRIPTION "Maximum amount of MAC level data the MS is capable of processing per DL frame. A value of 0 indicates such limitation does not exist, except the limitation of the physical medium" REFERENCE "Subclause 11.7.8.10.1 in IEEE Std 802.16e-2005" DEFVAL { 0 } ::= { wmanIf2BsOfdmaCapabilitiesConfigEntry 7 } wmanIf2eBsSsOfdmaCapCfgMaxMacLevelUlFm OBJECT-TYPE SYNTAX WmanIf2eMaxMacLevel MAX-ACCESS read-write STATUS current DESCRIPTION "Maximum amount of MAC level data the MS is capable of processing per UL frame. A value of 0 indicates such limitation does not exist, except the limitation of the physical medium" REFERENCE "Subclause 11.7.8.10.1 in IEEE Std 802.16e-2005" DEFVAL { 0 } ::= { wmanIf2BsOfdmaCapabilitiesConfigEntry 8 } wmanIf2eBsSsOfdmaCapCfgDemMimo OBJECT-TYPE SYNTAX WmanIf2eOfdmaDemMimo MAX-ACCESS read-write STATUS current DESCRIPTION "This field indicates the different MIMO options supported by a WirelessMAN-OFDMA PHY SS in the downlink." ::= { wmanIf2BsOfdmaCapabilitiesConfigEntry 9 } wmanIf2eBsSsOfdmaCapCfgMimoCapability OBJECT-TYPE SYNTAX WmanIf2eOfdmaMimoCap MAX-ACCESS read-write STATUS current DESCRIPTION "This field indicates the MIMO capability of OFDMA MS demodulator." ::= { wmanIf2BsOfdmaCapabilitiesConfigEntry 10 } wmanIf2eBsSsOfdmaCapCfgUlMimo OBJECT-TYPE SYNTAX WmanIf2eOfdmaUlMimo MAX-ACCESS read-write STATUS current DESCRIPTION "This field indicates different MIMO options supported by a OFDMA PHY SS in the uplink" REFERENCE "Subclause 11.8.3.7.6 in IEEE 802.16e" ::= { wmanIf2BsOfdmaCapabilitiesConfigEntry 11 } wmanIf2eBsSsOfdmaCapCfgPrivateMap OBJECT-TYPE SYNTAX WmanIf2eOfdmaPrivMap MAX-ACCESS read-write STATUS current DESCRIPTION "This field indicates AAS private map parameters supported by a OFDMA SS" REFERENCE "Subclause 11.8.3.7.7 in IEEE 802.16e" ::= { wmanIf2BsOfdmaCapabilitiesConfigEntry 12 } wmanIf2eBsSsOfdmaCapCfgAasCapability OBJECT-TYPE SYNTAX WmanIf2eOfdmaAasCap MAX-ACCESS read-write STATUS current DESCRIPTION "This field indicates different AAS options supported by a OFDMA PHY SS in the downlink" REFERENCE "Subclause 11.8.3.7.8 in IEEE 802.16e" ::= { wmanIf2BsOfdmaCapabilitiesConfigEntry 13 } wmanIf2eBsSsOfdmaCapCfgCinrMesurement OBJECT-TYPE SYNTAX WmanIf2eOfdmaCinrCap MAX-ACCESS read-write STATUS current DESCRIPTION "This field indicates the CINR measurement capability supported by a OFDMA PHY SS in the downlink." REFERENCE "Subclause 11.8.3.7.9 in IEEE 802.16e" ::= { wmanIf2BsOfdmaCapabilitiesConfigEntry 14 } wmanIf2eBsSsOfdmaCapCfgUlPowerControl OBJECT-TYPE SYNTAX WmanIf2eOfdmaUlPower MAX-ACCESS read-write STATUS current DESCRIPTION "This field indicates the power control options supported by a OFDMA PHY SS for uplink transmission." REFERENCE "Subclause 11.8.3.7.11 in IEEE 802.16e" ::= { wmanIf2BsOfdmaCapabilitiesConfigEntry 15 } wmanIf2eBsSsOfdmaCapCfgMapCapability OBJECT-TYPE SYNTAX WmanIf2eOfdmaMapCap MAX-ACCESS read-write STATUS current DESCRIPTION "This field indicates the different MAP options supported by a OFDMA PHY SS" REFERENCE "Subclause 11.8.3.7.11 in IEEE 802.16e" ::= { wmanIf2BsOfdmaCapabilitiesConfigEntry 16 } wmanIf2eBsSsOfdmaCapCfgUlControlChannel OBJECT-TYPE SYNTAX WmanIf2eOfdmaUlCntlCh MAX-ACCESS read-write STATUS current DESCRIPTION "This field indicates the different uplink control channels supported by a OFDMA PHY SS." REFERENCE "Subclause 11.8.3.7.13 in IEEE 802.16e" ::= { wmanIf2BsOfdmaCapabilitiesConfigEntry 17 } wmanIf2eBsSsOfdmaCapCfgCistCapability OBJECT-TYPE SYNTAX WmanIf2eOfdmaMsCistCap MAX-ACCESS read-write STATUS current DESCRIPTION "This field indicates the MS capability of supporting CSIT (uplink sounding)." REFERENCE "Subclause 11.8.3.7.14 in IEEE 802.16e" ::= { wmanIf2BsOfdmaCapabilitiesConfigEntry 18 } wmanIf2eBsSsOfdmaCapCfgMaxHarqBurst OBJECT-TYPE SYNTAX WmanIf2eOfdmaMaxHarq MAX-ACCESS read-write STATUS current DESCRIPTION "This field indicates the maximum number of UL/DL HARQ burst allocations for the SS in a single UL/DL subframe." REFERENCE "Subclause 11.8.3.7.15 in IEEE 802.16e" ::= { wmanIf2BsOfdmaCapabilitiesConfigEntry 19 } wmanIf2eBsSsOfdmaCapCfgModMimo OBJECT-TYPE SYNTAX WmanIf2eOfdmaModMimo MAX-ACCESS read-write STATUS current DESCRIPTION "This field indicates the MIMO capability of OFDMA SS modulator." REFERENCE "Subclause 11.8.3.7.16 in IEEE 802.16e" ::= { wmanIf2BsOfdmaCapabilitiesConfigEntry 20 } wmanIf2eBsSsOfdmaCapCfgSdmaPilot OBJECT-TYPE SYNTAX WmanIf2eSdmaPilotCap MAX-ACCESS read-write STATUS current DESCRIPTION "This field indicates the SDMA pilot pattern support for AMC zone." REFERENCE "Subclause 11.8.3.7.17 in IEEE 802.16e" ::= { wmanIf2BsOfdmaCapabilitiesConfigEntry 21 } wmanIf2eBsSsOfdmaCapCfgMultipleBurst OBJECT-TYPE SYNTAX WmanIf2eMultiBurst MAX-ACCESS read-write STATUS current DESCRIPTION "This field indicates whether multiple FEC types are supported in DL/UL burst profiles." REFERENCE "Subclause 11.8.3.7.18 in IEEE 802.16e" ::= { wmanIf2BsOfdmaCapabilitiesConfigEntry 22 } wmanIf2eBsSsOfdmaCapCfgIncrHarqBuffer OBJECT-TYPE SYNTAX WmanIf2eIncrHarqBuf MAX-ACCESS read-write STATUS current DESCRIPTION "This field indicates the maximal number of data bits the SS is able to use for buffering for NEP/NSCH based incremental redundancy CTC in downlink and uplink transmissions." REFERENCE "Subclause 11.8.3.7.19 in IEEE 802.16e" ::= { wmanIf2BsOfdmaCapabilitiesConfigEntry 23 } wmanIf2eBsSsOfdmaCapCfgChaseHarqBuffer OBJECT-TYPE SYNTAX WmanIf2eChaseHarqBuf MAX-ACCESS read-write STATUS current DESCRIPTION "This field indicates the maximal number of data bits the SS is able to use for buffering for DIUC/duration based HARQ methods (Chase combining and CC-IR)in downlink and uplink transmissions." REFERENCE "Subclause 11.8.3.7.19 in IEEE 802.16e" ::= { wmanIf2BsOfdmaCapabilitiesConfigEntry 24 } wmanIf2eBsOfdmaUplinkChannelTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2eBsOfdmaUplinkChannelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains UCD channel attributes, defining the transmission characteristics of uplink channels" REFERENCE "Table 349 and Table 353, in IEEE Std 802.16-2004" ::= { wmanIf2BsOfdmaPhy 9 } wmanIf2eBsOfdmaUplinkChannelEntry OBJECT-TYPE SYNTAX WmanIf2eBsOfdmaUplinkChannelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each uplink channel of multi-sector BS, and is indexed by BS ifIndex. An entry in this table exists for each ifEntry of BS with an ifType of propBWAp2Mp." AUGMENTS { wmanIf2BsOfdmaUplinkChannelEntry } ::= { wmanIf2eBsOfdmaUplinkChannelTable 1 } WmanIf2eBsOfdmaUplinkChannelEntry ::= SEQUENCE { wmanIf2eBsOfdmaHandoverRangingStart INTEGER, wmanIf2eBsOfdmaHandoverRangingEnd INTEGER, wmanIf2eBsOfdmaHARQAackDelayDLBurst WmanIf2eHarqAckDelay, wmanIf2eBsOfdmaUlAmcAlloPhyBandsBitmap OCTET STRING, wmanIf2eBsOfdmaMaxRetransmission INTEGER, wmanIf2eBsOfdmaNormalizedCnOverride OCTET STRING, wmanIf2eBsOfdmaSizeOfCqichId INTEGER, wmanIf2eBsOfdmaNormalizedCnValue INTEGER, wmanIf2eBsOfdmaNormalizedCnOverride2 OCTET STRING, wmanIf2eBsOfdmaBandAmcEntryAvgCinr INTEGER, wmanIf2eBsOfdmaAasPreambleUpperBond INTEGER, wmanIf2eBsOfdmaAasPreambleLowerBond INTEGER, wmanIf2eBsOfdmaAasBeamSelectAllowed WmanIf2eAasBeamSel, wmanIf2eBsOfdmaCqichIndicationFlag OCTET STRING, wmanIf2eBsOfdmaUpPowerAdjStep Unsigned32, wmanIf2eBsOfdmaDownPowerAdjStep Unsigned32, wmanIf2eBsOfdmaMinPowerOffsetAdj INTEGER, wmanIf2eBsOfdmaMaxPowerOffsetAdj INTEGER, wmanIf2eBsOfdmaHandoverRngCodes INTEGER, wmanIf2eBsOfdmaTxPwrRepThreshold INTEGER, wmanIf2eBsOfdmaTprPower INTEGER, wmanIf2eBsOfdmaAlphaPavg INTEGER, wmanIf2eBsOfdmaCqichTxPwrRepThreshold INTEGER, wmanIf2eBsOfdmaCqichTprPower INTEGER, wmanIf2eBsOfdmaCqichAlphaPavg INTEGER, wmanIf2eBsOfdmaNormalizedCnChSounding INTEGER, wmanIf2eBsOfdmaInitialRngInterval INTEGER, wmanIf2eBsOfdmaInitialRngBackoffStart INTEGER, wmanIf2eBsOfdmaInitialRngBackoffEnd INTEGER, wmanIf2eBsOfdmaBwRequestBackoffStart INTEGER, wmanIf2eBsOfdmaBwRequestBackoffEnd INTEGER} wmanIf2eBsOfdmaHandoverRangingStart OBJECT-TYPE SYNTAX INTEGER (0..15) MAX-ACCESS read-write STATUS current DESCRIPTION "Initial backoff window size for MS performing initial ranging during handover process, expressed as a power of 2." REFERENCE "Table 349, in IEEE Std 802.16e-2005" ::= { wmanIf2eBsOfdmaUplinkChannelEntry 1 } wmanIf2eBsOfdmaHandoverRangingEnd OBJECT-TYPE SYNTAX INTEGER (0..15) MAX-ACCESS read-write STATUS current DESCRIPTION "Final backoff window size for MS performing initial ranging during handover process, expressed as a power of 2." REFERENCE "Table 349, in IEEE Std 802.16e-2005" ::= { wmanIf2eBsOfdmaUplinkChannelEntry 2 } wmanIf2eBsOfdmaHARQAackDelayDLBurst OBJECT-TYPE SYNTAX WmanIf2eHarqAckDelay MAX-ACCESS read-write STATUS current DESCRIPTION "This object defines the OFDMA H-ARQ ACK delay for DL burst." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16e-2005" ::= { wmanIf2eBsOfdmaUplinkChannelEntry 3 } wmanIf2eBsOfdmaUlAmcAlloPhyBandsBitmap OBJECT-TYPE SYNTAX OCTET STRING (SIZE (6)) MAX-ACCESS read-write STATUS current DESCRIPTION "A bitmap describing the physical bands allocated to the segment in the UL, when using the optional AMC permutation with regular MAPs (see 8.4.6.3). The LSB of the first byte shall correspond to the physical band 0. For any bit that is not set, the corresponding physical bands shall not be used by the SS on that segment. When this TLV is not present, BS may allocate any physical bands to an SS." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16e-2005" ::= { wmanIf2eBsOfdmaUplinkChannelEntry 4 } wmanIf2eBsOfdmaMaxRetransmission OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Maximum number of retransmission in UL HARQ." REFERENCE "Table 353, in IEEE Std 802.16e-2005" DEFVAL { 4 } ::= { wmanIf2eBsOfdmaUplinkChannelEntry 5 } wmanIf2eBsOfdmaNormalizedCnOverride OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) MAX-ACCESS read-write STATUS current DESCRIPTION "This is a list of numbers, where each number is encoded by one nibble, and interpreted as a signed integer. The nibbles correspond in order to the list define by Table 334, starting from the second line, such that the LS nibble of the first byte corresponds to the second line in the table. The number encoded by each nibble represents the difference in normalized C/N relative to the previous line in the table." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16e-2005" ::= { wmanIf2eBsOfdmaUplinkChannelEntry 6 } wmanIf2eBsOfdmaSizeOfCqichId OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Size of CQICH ID field. 0 = 0 bits 1 = 3 bits 2 = 4 bits 3 = 5 bits 4 = 6 bits 5 = 7 bits 6 = 8 bits 7 = 9 bits" REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16e-2005" DEFVAL { 0 } ::= { wmanIf2eBsOfdmaUplinkChannelEntry 7 } wmanIf2eBsOfdmaNormalizedCnValue OBJECT-TYPE SYNTAX INTEGER (-128..128) UNITS "dB" MAX-ACCESS read-write STATUS current DESCRIPTION "It shall be interpreted as signed integer in dB. It corresponds to the normalized C/N value in the first line (counting except for header cell of table)" REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16e-2005" ::= { wmanIf2eBsOfdmaUplinkChannelEntry 8 } wmanIf2eBsOfdmaNormalizedCnOverride2 OBJECT-TYPE SYNTAX OCTET STRING (SIZE (7)) MAX-ACCESS read-write STATUS current DESCRIPTION "This is a list of numbers, where each number is encoded by one nibble, and interpreted as a signed integer. The nibbles correspond in order to the list define by Table 334, starting from the second line (counting except for the header cell of table), such that the LS nibble of the first byte corresponds to the second line in the table. The number encoded by each nibble represents the difference in normalized C/N relative to the previous line in the table." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16e-2005" ::= { wmanIf2eBsOfdmaUplinkChannelEntry 9 } wmanIf2eBsOfdmaBandAmcEntryAvgCinr OBJECT-TYPE SYNTAX INTEGER (-128..128) UNITS "dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Threshold of the average CINR of the whole bandwidth to trigger mode transition from normal subchannel to AMC" REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16e-2005" ::= { wmanIf2eBsOfdmaUplinkChannelEntry 10 } wmanIf2eBsOfdmaAasPreambleUpperBond OBJECT-TYPE SYNTAX INTEGER (-128..128) UNITS "0.25 dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Upper bound of AAS preamble." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16e-2005" ::= { wmanIf2eBsOfdmaUplinkChannelEntry 11 } wmanIf2eBsOfdmaAasPreambleLowerBond OBJECT-TYPE SYNTAX INTEGER (-128..128) UNITS "0.25 dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Lower bound of AAS preamble." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16e-2005" ::= { wmanIf2eBsOfdmaUplinkChannelEntry 12 } wmanIf2eBsOfdmaAasBeamSelectAllowed OBJECT-TYPE SYNTAX WmanIf2eAasBeamSel UNITS "0.25 dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Indicate whether unsolicited AAS Beam Select messages (see 6.3.2.3.41 in IEEE 802.16e-2005) should be sent by the MS." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16e-2005" DEFVAL { allowed } ::= { wmanIf2eBsOfdmaUplinkChannelEntry 13 } wmanIf2eBsOfdmaCqichIndicationFlag OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1)) MAX-ACCESS read-write STATUS current DESCRIPTION "The N MSB values of this field represents the N-bit payload value on the Fast-Feedback channel reserved as indication flag for MS to initiate feedback on the Feedback header, where N is the number of payload bits used for S/N measurement feedback on the Fast-Feedback channel. The value shall not be set to all zeros." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16e-2005" ::= { wmanIf2eBsOfdmaUplinkChannelEntry 14 } wmanIf2eBsOfdmaUpPowerAdjStep OBJECT-TYPE SYNTAX Unsigned32 UNITS "0.01 dB" MAX-ACCESS read-write STATUS current DESCRIPTION "MS-specific up power offset adjustment step" REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16e-2005" ::= { wmanIf2eBsOfdmaUplinkChannelEntry 15 } wmanIf2eBsOfdmaDownPowerAdjStep OBJECT-TYPE SYNTAX Unsigned32 UNITS "0.01 dB" MAX-ACCESS read-write STATUS current DESCRIPTION "MS-specific down power offset adjustment step" REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16e-2005" ::= { wmanIf2eBsOfdmaUplinkChannelEntry 16 } wmanIf2eBsOfdmaMinPowerOffsetAdj OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Minimum level of power offset adjustment" REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16e-2005" ::= { wmanIf2eBsOfdmaUplinkChannelEntry 17 } wmanIf2eBsOfdmaMaxPowerOffsetAdj OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Minimum level of power offset adjustment" REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16e-2005" ::= { wmanIf2eBsOfdmaUplinkChannelEntry 18 } wmanIf2eBsOfdmaHandoverRngCodes OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Number of handover ranging CDMA codes" REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16e-2005" ::= { wmanIf2eBsOfdmaUplinkChannelEntry 19 } wmanIf2eBsOfdmaInitialRngInterval OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Number of frames between initial ranging interval allocation." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16e-2005" ::= { wmanIf2eBsOfdmaUplinkChannelEntry 20 } wmanIf2eBsOfdmaTxPwrRepThreshold OBJECT-TYPE SYNTAX INTEGER (0..15) UNITS "dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Tx power report threshold. wmanIf2eBsOfdmaTxPwrRepThreshold = 0b1111 means infinite." REFERENCE "Subclause 11.3.1, Table 353, and 8.4.10.3.2.1 in IEEE Std 802.16e-2005" ::= { wmanIf2eBsOfdmaUplinkChannelEntry 21 } wmanIf2eBsOfdmaTprPower OBJECT-TYPE SYNTAX INTEGER (0..15) UNITS "dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Tx power report interval = 2 ^ wmanIf2eBsOfdmaTprPower. The unit of Tx power report interval is frame. wmanIf2eBsOfdmaTprPower = 0b1111 means infinite." REFERENCE "Subclause 11.3.1, Table 353, and 8.4.10.3.2.1 in IEEE Std 802.16e-2005" ::= { wmanIf2eBsOfdmaUplinkChannelEntry 22 } wmanIf2eBsOfdmaAlphaPavg OBJECT-TYPE SYNTAX INTEGER (0..15) UNITS "dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Aplha p_avg parameter as shown in equation 138d in IEEE 802.16e-2005 indicates the multiple of 1/16. For example '0' means 1/16, 15 means 16/16. " REFERENCE "Subclause 11.3.1, Table 353, and 8.4.10.3.2.1 in IEEE Std 802.16e-2005" ::= { wmanIf2eBsOfdmaUplinkChannelEntry 23 } wmanIf2eBsOfdmaCqichTxPwrRepThreshold OBJECT-TYPE SYNTAX INTEGER (0..15) UNITS "dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Tx power report threshold. wmanIf2eBsOfdmaTxPwrRepThreshold = 0b1111 means infinite. It shall be used when CQICH is allocated to the SS." REFERENCE "Subclause 11.3.1, Table 353, and 8.4.10.3.2.1 in IEEE Std 802.16e-2005" ::= { wmanIf2eBsOfdmaUplinkChannelEntry 24 } wmanIf2eBsOfdmaCqichTprPower OBJECT-TYPE SYNTAX INTEGER (0..15) UNITS "dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Tx power report interval = 2 ^ wmanIf2eBsOfdmaTprPower. The unit of Tx power report interval is frame. wmanIf2eBsOfdmaTprPower = 0b1111 means infinite. It shall be used when CQICH is allocated to the SS." REFERENCE "Subclause 11.3.1, Table 353, and 8.4.10.3.2.1 in IEEE Std 802.16e-2005" ::= { wmanIf2eBsOfdmaUplinkChannelEntry 25 } wmanIf2eBsOfdmaCqichAlphaPavg OBJECT-TYPE SYNTAX INTEGER (0..15) UNITS "dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Aplha p_avg parameter as shown in equation 138d in IEEE 802.16e-2005 indicates the multiple of 1/16. For example '0' means 1/16, 15 means 16/16. It shall be used when CQICH is allocated to the SS." REFERENCE "Subclause 11.3.1, Table 353, and 8.4.10.3.2.1 in IEEE Std 802.16e-2005" ::= { wmanIf2eBsOfdmaUplinkChannelEntry 26 } wmanIf2eBsOfdmaNormalizedCnChSounding OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Signed integer for the required C/N (dB) for Channel Sounding." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16e-2005" ::= { wmanIf2eBsOfdmaUplinkChannelEntry 27 } wmanIf2eBsOfdmaInitialRngBackoffStart OBJECT-TYPE SYNTAX INTEGER (0..15) MAX-ACCESS read-write STATUS current DESCRIPTION "Initial backoff window size for initial ranging contention, expressed as a power of 2." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16e-2005" ::= { wmanIf2eBsOfdmaUplinkChannelEntry 28 } wmanIf2eBsOfdmaInitialRngBackoffEnd OBJECT-TYPE SYNTAX INTEGER (0..15) MAX-ACCESS read-write STATUS current DESCRIPTION "Final backoff window size for initial ranging contention, expressed as a power of 2." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16e-2005" ::= { wmanIf2eBsOfdmaUplinkChannelEntry 29 } wmanIf2eBsOfdmaBwRequestBackoffStart OBJECT-TYPE SYNTAX INTEGER (0..15) MAX-ACCESS read-write STATUS current DESCRIPTION "Initial backoff window size for contention BW requests, expressed as a power of 2." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16e-2005" ::= { wmanIf2eBsOfdmaUplinkChannelEntry 30 } wmanIf2eBsOfdmaBwRequestBackoffEnd OBJECT-TYPE SYNTAX INTEGER (0..15) MAX-ACCESS read-write STATUS current DESCRIPTION "Final backoff window size for contention BW requests, expressed as a power of 2." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16e-2005" ::= { wmanIf2eBsOfdmaUplinkChannelEntry 31 } -- -- SS object group – containing tables and objects to be implemented in -- the Subscriber station -- -- wmanIf2SsCps contain the SS Common Part Sublayer objects -- wmanIf2SsCps OBJECT IDENTIFIER ::= { wmanIf2SsObjects 1 } -- -- wmanIf2SsConfigurationTable contains global parameters for SS -- wmanIf2SsConfigurationTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2SsConfigurationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one row for the SS system parameters." REFERENCE "Subclause 10.1 in IEEE Std 802.16-2004" ::= { wmanIf2SsCps 1 } wmanIf2SsConfigurationEntry OBJECT-TYPE SYNTAX WmanIf2SsConfigurationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is indexed by ifIndex." INDEX { ifIndex } ::= { wmanIf2SsConfigurationTable 1 } WmanIf2SsConfigurationEntry ::= SEQUENCE { wmanIf2SsLostDLMapInterval INTEGER, wmanIf2SsLostULMapInterval INTEGER, wmanIf2SsContentionRangRetries INTEGER, wmanIf2SsRequestRetries INTEGER, wmanIf2SsRegRequestRetries INTEGER, wmanIf2SsTftpBackoffStart INTEGER, wmanIf2SsTftpBackoffEnd INTEGER, wmanIf2SsTftpRequestRetries INTEGER, wmanIf2SsTftpDownloadRetries INTEGER, wmanIf2SsTftpWait INTEGER, wmanIf2SsToDRetries INTEGER, wmanIf2SsToDRetryPeriod INTEGER, wmanIf2SsT1Timeout INTEGER, wmanIf2SsT2Timeout INTEGER, wmanIf2SsT3Timeout INTEGER, wmanIf2SsT4Timeout INTEGER, wmanIf2SsT6Timeout INTEGER, wmanIf2SsT12Timeout INTEGER, wmanIf2SsT14Timeout INTEGER, wmanIf2SsT16Timeout INTEGER, wmanIf2SsT18Timeout INTEGER, wmanIf2SsT19Timeout INTEGER, wmanIf2SsT20Timeout INTEGER, wmanIf2SsT21Timeout INTEGER, wmanIf2SsSBCRequestRetries INTEGER, wmanIf2SsTftpCpltRetries INTEGER, wmanIf2SsT26Timeout INTEGER, wmanIf2SsDLManagProcTime INTEGER} wmanIf2SsLostDLMapInterval OBJECT-TYPE SYNTAX INTEGER (0..600) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Time since last received DL-MAP message before downlink synchronization is considered lost in ms." ::= { wmanIf2SsConfigurationEntry 1 } wmanIf2SsLostULMapInterval OBJECT-TYPE SYNTAX INTEGER (0..600) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Time since last received UL-MAP message before uplink synchronization is considered lost in ms." ::= { wmanIf2SsConfigurationEntry 2 } wmanIf2SsContentionRangRetries OBJECT-TYPE SYNTAX INTEGER (16..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Number of retries on contention Ranging Requests." ::= { wmanIf2SsConfigurationEntry 3 } wmanIf2SsRequestRetries OBJECT-TYPE SYNTAX INTEGER (16..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Number of retries on bandwidth allocation requests." ::= { wmanIf2SsConfigurationEntry 4 } wmanIf2SsRegRequestRetries OBJECT-TYPE SYNTAX INTEGER (3..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Number of retries on registration requests." ::= { wmanIf2SsConfigurationEntry 5 } wmanIf2SsTftpBackoffStart OBJECT-TYPE SYNTAX INTEGER (1..65535) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Initial value for TFTP backoff in second." ::= { wmanIf2SsConfigurationEntry 6 } wmanIf2SsTftpBackoffEnd OBJECT-TYPE SYNTAX INTEGER (16..65535) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Last value for TFTP backoff in second." ::= { wmanIf2SsConfigurationEntry 7 } wmanIf2SsTftpRequestRetries OBJECT-TYPE SYNTAX INTEGER (16..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Number of retries on TFTP request." ::= { wmanIf2SsConfigurationEntry 8 } wmanIf2SsTftpDownloadRetries OBJECT-TYPE SYNTAX INTEGER (3..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Number of retries on entire TFTP downloads." ::= { wmanIf2SsConfigurationEntry 9 } wmanIf2SsTftpWait OBJECT-TYPE SYNTAX INTEGER (2..65535) UNITS "minutes" MAX-ACCESS read-write STATUS current DESCRIPTION "The duration between two consecutive Transfer operational parameters (TFTP) retries in min." ::= { wmanIf2SsConfigurationEntry 10 } wmanIf2SsToDRetries OBJECT-TYPE SYNTAX INTEGER (3..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Number of Retries to establisg the Time of Day." ::= { wmanIf2SsConfigurationEntry 11 } wmanIf2SsToDRetryPeriod OBJECT-TYPE SYNTAX INTEGER (5..65535) UNITS "minutes" MAX-ACCESS read-write STATUS current DESCRIPTION "The retry period to re-establisg the Time of Day, as describe in the network entry procedure." ::= { wmanIf2SsConfigurationEntry 12 } wmanIf2SsT1Timeout OBJECT-TYPE SYNTAX INTEGER (0..50000) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Wait for DCD timeout in ms." ::= { wmanIf2SsConfigurationEntry 13 } wmanIf2SsT2Timeout OBJECT-TYPE SYNTAX INTEGER (0..10000) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Wait for broadcast ranging timeout in ms." ::= { wmanIf2SsConfigurationEntry 14 } wmanIf2SsT3Timeout OBJECT-TYPE SYNTAX INTEGER (0..200) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Ranging Response reception timeout following the transmission of a Ranging Request in ms." ::= { wmanIf2SsConfigurationEntry 15 } wmanIf2SsT4Timeout OBJECT-TYPE SYNTAX INTEGER (30..35) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Wait for unicast ranging opportunity. If the pending until complete field was used earlier by this SS, then the value of that field shall be added to this interval in second." ::= { wmanIf2SsConfigurationEntry 16 } wmanIf2SsT6Timeout OBJECT-TYPE SYNTAX INTEGER (0..3000) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Wait for registration response in ms." ::= { wmanIf2SsConfigurationEntry 17 } wmanIf2SsT12Timeout OBJECT-TYPE SYNTAX INTEGER (0..50000) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Wait for UCD descriptor in ms." ::= { wmanIf2SsConfigurationEntry 18 } wmanIf2SsT14Timeout OBJECT-TYPE SYNTAX INTEGER (0..200) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Wait for DSX-RVD Timeout in ms." ::= { wmanIf2SsConfigurationEntry 19 } wmanIf2SsT16Timeout OBJECT-TYPE SYNTAX INTEGER (10..65535) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "wait for bandwidth request grant in ms." ::= { wmanIf2SsConfigurationEntry 20 } wmanIf2SsT18Timeout OBJECT-TYPE SYNTAX INTEGER (0..65535) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "wait for SBC-RSP timeout in ms." ::= { wmanIf2SsConfigurationEntry 21 } wmanIf2SsT19Timeout OBJECT-TYPE SYNTAX INTEGER (0..1048575) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Time DL-channel remains unusable in ms." ::= { wmanIf2SsConfigurationEntry 22 } wmanIf2SsT20Timeout OBJECT-TYPE SYNTAX INTEGER (0..65535) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Time SS searches for preambles on a given channel in ms." ::= { wmanIf2SsConfigurationEntry 23 } wmanIf2SsT21Timeout OBJECT-TYPE SYNTAX INTEGER (0..10000) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Time SS searches for DL-MAP on a given channel in ms." ::= { wmanIf2SsConfigurationEntry 24 } wmanIf2SsSBCRequestRetries OBJECT-TYPE SYNTAX INTEGER (3..16) MAX-ACCESS read-write STATUS current DESCRIPTION "Number of retries on SBC Request." ::= { wmanIf2SsConfigurationEntry 25 } wmanIf2SsTftpCpltRetries OBJECT-TYPE SYNTAX INTEGER (3..16) MAX-ACCESS read-write STATUS current DESCRIPTION "Number of retries on TFTP-CPLT." ::= { wmanIf2SsConfigurationEntry 26 } wmanIf2SsT26Timeout OBJECT-TYPE SYNTAX INTEGER (10..200) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Wait for TFTP-RSP in ms." ::= { wmanIf2SsConfigurationEntry 27 } wmanIf2SsDLManagProcTime OBJECT-TYPE SYNTAX INTEGER (0..200) UNITS "micro seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Max. time between reception of Fast Power Control management message and compliance to its instructions by SS in us." ::= { wmanIf2SsConfigurationEntry 28 } -- -- Subscriber Channel Measurement Table -- wmanIf2SsChannelMeasurementTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2SsChannelMeasurementEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains downlink channel measurement information for each SS." REFERENCE "6.3.2.3.33 in IEEE Std 802.16-2004" ::= { wmanIf2SsCps 2 } wmanIf2SsChannelMeasurementEntry OBJECT-TYPE SYNTAX WmanIf2SsChannelMeasurementEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in the table contains RSSI and CINR signal quality measurement taken from the SS. The primary index is the ifIndex pointing to SS. wmanIf2CmnHistogramIndex is the index to histogram samples. Since there is no time stamp in the table, wmanIf2SsHistogramIndex should be increased monotonically, and wraps around when it reaches the limit. When the measurement entry for a SS reaches the limit, the oldest entry shall be deleted as the new entry is added to the table." INDEX { ifIndex, wmanIf2SsHistogramIndex } ::= { wmanIf2SsChannelMeasurementTable 1 } WmanIf2SsChannelMeasurementEntry ::= SEQUENCE { wmanIf2SsHistogramIndex Unsigned32, wmanIf2SsChannelNumber WmanIf2ChannelNumber, wmanIf2SsStartFrame INTEGER, wmanIf2SsDuration INTEGER, wmanIf2SsBasicReport BITS, wmanIf2SsMeanCinrReport INTEGER, wmanIf2SsStdDeviationCinrReport INTEGER, wmanIf2SsMeanRssiReport INTEGER, wmanIf2SsStdDeviationRssiReport INTEGER} wmanIf2SsHistogramIndex OBJECT-TYPE SYNTAX Unsigned32 (1 .. 4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "wmanIf2SsHistogramIndex identifies the histogram samples in the table for each subscriber station." ::= { wmanIf2SsChannelMeasurementEntry 1 } wmanIf2SsChannelNumber OBJECT-TYPE SYNTAX WmanIf2ChannelNumber MAX-ACCESS read-only STATUS current DESCRIPTION "Physical channel number to be reported on." REFERENCE "Subclause 8.5.1 in IEEE Std 802.16-2004" ::= { wmanIf2SsChannelMeasurementEntry 2 } wmanIf2SsStartFrame OBJECT-TYPE SYNTAX INTEGER (0 .. 65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Frame number in which measurement for this channel started." REFERENCE "Subclause 11.12 in IEEE Std 802.16-2004" ::= { wmanIf2SsChannelMeasurementEntry 3 } wmanIf2SsDuration OBJECT-TYPE SYNTAX INTEGER (0..16777215) MAX-ACCESS read-only STATUS current DESCRIPTION "Cumulative measurement duration on the channel in multiples of Ts. For any value exceeding 0xFFFFFF, report 0xFFFFFF." REFERENCE "Subclause 11.12 in IEEE Std 802.16-2004" ::= { wmanIf2SsChannelMeasurementEntry 4 } wmanIf2SsBasicReport OBJECT-TYPE SYNTAX BITS {wirelessHuman(0), unknownTransmission(1), primaryUser(2), channelNotMeasured(3)} MAX-ACCESS read-only STATUS current DESCRIPTION "Bit #0: WirelessHUMAN detected on the channel Bit #1: Unknown transmissions detected on the channel Bit #2: Primary User detected on the channel Bit #3: Unmeasured. Channel not measured" REFERENCE "Subclause 11.12 in IEEE Std 802.16-2004" ::= { wmanIf2SsChannelMeasurementEntry 5 } wmanIf2SsMeanCinrReport OBJECT-TYPE SYNTAX INTEGER (0 .. 41) UNITS "dB" MAX-ACCESS read-only STATUS current DESCRIPTION "Mean CINR report." REFERENCE "Subclause 8.2.2, 8.3.9 in IEEE Std 802.16-2004" ::= { wmanIf2SsChannelMeasurementEntry 6 } wmanIf2SsStdDeviationCinrReport OBJECT-TYPE SYNTAX INTEGER (0 .. 41) UNITS "dB" MAX-ACCESS read-only STATUS current DESCRIPTION "Standard deviation CINR report." REFERENCE "Subclause 8.2.2 and Subclause 8.3.9 in IEEE Std 802.16-2004" ::= { wmanIf2SsChannelMeasurementEntry 7 } wmanIf2SsMeanRssiReport OBJECT-TYPE SYNTAX INTEGER (0 .. 83) UNITS "dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "Mean RSSI report." REFERENCE "Subclause 8.2.2 and Subclause 8.3.9 in IEEE Std 802.16-2004" ::= { wmanIf2SsChannelMeasurementEntry 8 } wmanIf2SsStdDeviationRssiReport OBJECT-TYPE SYNTAX INTEGER (0 .. 83) UNITS "dB" MAX-ACCESS read-only STATUS current DESCRIPTION "Standard deviation RSSI report." REFERENCE "Subclause 8.2.2 and Subclause 8.3.9 in IEEE Std 802.16-2004" ::= { wmanIf2SsChannelMeasurementEntry 9 } -- -- Subscriber station PKM group -- wmanIf2SsPkmObjects contain the Subscriber Station Privacy Sublayer -- objects -- wmanIf2SsPkmObjects OBJECT IDENTIFIER ::= { wmanIf2SsObjects 2 } -- -- Table wmanIf2SsPkmAuthTable -- wmanIf2SsPkmAuthTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2SsPkmAuthEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the PKM attributes related to the authorization for each SS wireless interface." ::= { wmanIf2SsPkmObjects 1 } wmanIf2SsPkmAuthEntry OBJECT-TYPE SYNTAX WmanIf2SsPkmAuthEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains objects describing attributes of one SS wireless interface." INDEX { ifIndex } ::= { wmanIf2SsPkmAuthTable 1 } WmanIf2SsPkmAuthEntry ::= SEQUENCE { wmanIf2SsPkmAuthState INTEGER, wmanIf2SsPkmAuthKeySequenceNumber Integer32, wmanIf2SsPkmAuthExpiresOld DateAndTime, wmanIf2SsPkmAuthExpiresNew DateAndTime, wmanIf2SsPkmAuthReset TruthValue, wmanIf2SsPkmAuthentInfos Counter32, wmanIf2SsPkmAuthRequests Counter32, wmanIf2SsPkmAuthReplies Counter32, wmanIf2SsPkmAuthRejects Counter32, wmanIf2SsPkmAuthInvalids Counter32, wmanIf2SsPkmAuthRejectErrorCode INTEGER, wmanIf2SsPkmAuthRejectErrorString SnmpAdminString, wmanIf2SsPkmAuthInvalidErrorCode INTEGER, wmanIf2SsPkmAuthInvalidErrorString SnmpAdminString, wmanIf2SsPkmAuthGraceTime Integer32, wmanIf2SsPkmTekGraceTime Integer32, wmanIf2SsPkmAuthWaitTimeout Integer32, wmanIf2SsPkmReauthWaitTimeout Integer32, wmanIf2SsPkmOpWaitTimeout Integer32, wmanIf2SsPkmRekeyWaitTimeout Integer32, wmanIf2SsPkmAuthRejectWaitTimeout Integer32} wmanIf2SsPkmAuthState OBJECT-TYPE SYNTAX INTEGER {start(1), authWait(2), authorized(3), reauthWait(4), authRejectWait(5), silent(6)} MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the state of the SS authorization FSM. The start state indicates that FSM is in its initial state." ::= { wmanIf2SsPkmAuthEntry 1 } wmanIf2SsPkmAuthKeySequenceNumber OBJECT-TYPE SYNTAX Integer32 (0..15) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the most recent authorization key sequence number for this FSM." ::= { wmanIf2SsPkmAuthEntry 2 } wmanIf2SsPkmAuthExpiresOld OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the actual clock time for expiration of the immediate predecessor of the most recent authorization key for this FSM. If this FSM has only one authorization key, then the value is the time of activation of this FSM." ::= { wmanIf2SsPkmAuthEntry 3 } wmanIf2SsPkmAuthExpiresNew OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the actual clock time for expiration of the most recent authorization key for this FSM." ::= { wmanIf2SsPkmAuthEntry 4 } wmanIf2SsPkmAuthReset OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object to TRUE generates a Reauthorize event in the authorization FSM. Reading this object always returns FALSE." ::= { wmanIf2SsPkmAuthEntry 5 } wmanIf2SsPkmAuthentInfos OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the SS has transmitted an Authentication Information message." ::= { wmanIf2SsPkmAuthEntry 6 } wmanIf2SsPkmAuthRequests OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the SS has transmitted an Authorization Request message." ::= { wmanIf2SsPkmAuthEntry 7 } wmanIf2SsPkmAuthReplies OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the SS has received an Authorization Reply message." ::= { wmanIf2SsPkmAuthEntry 8 } wmanIf2SsPkmAuthRejects OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the SS has received an Authorization Reject message." ::= { wmanIf2SsPkmAuthEntry 9 } wmanIf2SsPkmAuthInvalids OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the SS has received an Authorization Invalid message." ::= { wmanIf2SsPkmAuthEntry 10 } wmanIf2SsPkmAuthRejectErrorCode OBJECT-TYPE SYNTAX INTEGER {none(1), unknown(2), unauthorizedSs(3), unauthorizedSaid(4), permanentAuthorizationFailure(8), timeOfDayNotAcquired(11)} MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the enumerated description of the Error-Code in most recent Authorization Reject message received by the SS. This has value unknown(2)if the last Error-Code value was 0, and none(1) if no Authorization Reject message has been received since reboot." ::= { wmanIf2SsPkmAuthEntry 11 } wmanIf2SsPkmAuthRejectErrorString OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the Display-String in most recent Authorization Reject message received by the SS. This is a zero length string if no Authorization Reject message has been received since reboot." ::= { wmanIf2SsPkmAuthEntry 12 } wmanIf2SsPkmAuthInvalidErrorCode OBJECT-TYPE SYNTAX INTEGER {none(1), unknown(2), unauthorizedSs(3), unsolicited(5), invalidKeySequence(6), keyRequestAuthenticationFailure(7)} MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the enumerated description of the Error-Code in most recent Authorization Invalid message received by the SS. This has value unknown(2) if the last Error-Code value was 0, and none(1) if no Authorization Invalid message has been received since reboot." ::= { wmanIf2SsPkmAuthEntry 13 } wmanIf2SsPkmAuthInvalidErrorString OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the Display-String in most recent Authorization Invalid message received by the SS. This is a zero length string if no Authorization Invalid message has been received since reboot." ::= { wmanIf2SsPkmAuthEntry 14 } wmanIf2SsPkmAuthGraceTime OBJECT-TYPE SYNTAX Integer32 (300..3024000) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the grace time for an authorization key. A SS is expected to start trying to get a new authorization key beginning AuthGraceTime seconds before the authorization key actually expires." REFERENCE "Table 343 in IEEE Std 802.16-2004" DEFVAL { 600 } ::= { wmanIf2SsPkmAuthEntry 15 } wmanIf2SsPkmTekGraceTime OBJECT-TYPE SYNTAX Integer32 (300..3024000) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the grace time for the TEK in seconds. The SS is expected to start trying to acquire a new TEK beginning TEK GraceTime seconds before the expiration of the most recent TEK." REFERENCE "Table 343 in IEEE Std 802.16-2004" DEFVAL { 3600 } ::= { wmanIf2SsPkmAuthEntry 16 } wmanIf2SsPkmAuthWaitTimeout OBJECT-TYPE SYNTAX Integer32 (2..30) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the Authorize Wait Timeout." REFERENCE "Table 343 in IEEE Std 802.16-2004" DEFVAL { 10 } ::= { wmanIf2SsPkmAuthEntry 17 } wmanIf2SsPkmReauthWaitTimeout OBJECT-TYPE SYNTAX Integer32 (2..30) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the Reauthorize Wait Timeout in seconds." REFERENCE "Table 343 in IEEE Std 802.16-2004" DEFVAL { 10 } ::= { wmanIf2SsPkmAuthEntry 18 } wmanIf2SsPkmOpWaitTimeout OBJECT-TYPE SYNTAX Integer32 (1..10) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the Operational Wait Timeout in seconds." REFERENCE "Table 343 in IEEE Std 802.16-2004" DEFVAL { 1 } ::= { wmanIf2SsPkmAuthEntry 19 } wmanIf2SsPkmRekeyWaitTimeout OBJECT-TYPE SYNTAX Integer32 (1..10) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the Rekey Wait Timeout in seconds." REFERENCE "Table 343 in IEEE Std 802.16-2004" DEFVAL { 1 } ::= { wmanIf2SsPkmAuthEntry 20 } wmanIf2SsPkmAuthRejectWaitTimeout OBJECT-TYPE SYNTAX Integer32 (10..600) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the Authorization Reject Wait Timeout in seconds." REFERENCE "Table 343 in IEEE Std 802.16-2004" DEFVAL { 60 } ::= { wmanIf2SsPkmAuthEntry 21 } -- -- Table wmanIf2SsPkmTekTable -- wmanIf2SsPkmTekTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2SsPkmTekEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the attributes of each SS Traffic Encryption Key(TEK) association. The SS maintains (no more than) one TEK association per SAID per SS wireless interface." ::= { wmanIf2SsPkmObjects 2 } wmanIf2SsPkmTekEntry OBJECT-TYPE SYNTAX WmanIf2SsPkmTekEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains objects describing the TEK association attributes of one SAID. The SS MUST create one entry per SAID, regardless of whether the SAID was obtained from a Registration Response message, from an Authorization Reply message, or from any dynamic SAID establishment mechanisms." INDEX { ifIndex, wmanIf2SsPkmTekSAId } ::= { wmanIf2SsPkmTekTable 1 } WmanIf2SsPkmTekEntry ::= SEQUENCE { wmanIf2SsPkmTekSAId INTEGER, wmanIf2SsPkmTekSAType INTEGER, wmanIf2SsPkmTekDataEncryptAlg WmanIf2DataEncryptAlgId, wmanIf2SsPkmTekDataAuthentAlg WmanIf2DataAuthAlgId, wmanIf2SsPkmTekEncryptAlg WmanIf2TekEncryptAlgId, wmanIf2SsPkmTekState INTEGER, wmanIf2SsPkmTekKeySequenceNumber Integer32, wmanIf2SsPkmTekExpiresOld DateAndTime, wmanIf2SsPkmTekExpiresNew DateAndTime, wmanIf2SsPkmTekKeyRequests Counter32, wmanIf2SsPkmTekKeyReplies Counter32, wmanIf2SsPkmTekKeyRejects Counter32, wmanIf2SsPkmTekInvalids Counter32, wmanIf2SsPkmTekAuthPends Counter32, wmanIf2SsPkmTekKeyRejectErrorCode INTEGER, wmanIf2SsPkmTekKeyRejectErrorString SnmpAdminString, wmanIf2SsPkmTekInvalidErrorCode INTEGER, wmanIf2SsPkmTekInvalidErrorString SnmpAdminString} wmanIf2SsPkmTekSAId OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The value of this object is the Security Association ID (SAID)." ::= { wmanIf2SsPkmTekEntry 1 } wmanIf2SsPkmTekSAType OBJECT-TYPE SYNTAX INTEGER {primarySA(0), staticSA(1), dynamicSA(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the type of security association." REFERENCE "IEEE Std 802.16-2004; 11.9.18" ::= { wmanIf2SsPkmTekEntry 2 } wmanIf2SsPkmTekDataEncryptAlg OBJECT-TYPE SYNTAX WmanIf2DataEncryptAlgId MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the data encryption algorithm being utilized." REFERENCE "Table 375, IEEE Std 802.16-2004" ::= { wmanIf2SsPkmTekEntry 3 } wmanIf2SsPkmTekDataAuthentAlg OBJECT-TYPE SYNTAX WmanIf2DataAuthAlgId MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the data authentication algorithm being utilized." REFERENCE "Table 376, IEEE Std 802.16-2004" ::= { wmanIf2SsPkmTekEntry 4 } wmanIf2SsPkmTekEncryptAlg OBJECT-TYPE SYNTAX WmanIf2TekEncryptAlgId MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the TEK key encryption algorithm for this cryptographic suite capability." REFERENCE "Table 377, IEEE Std 802.16-2004" ::= { wmanIf2SsPkmTekEntry 5 } wmanIf2SsPkmTekState OBJECT-TYPE SYNTAX INTEGER {start(1), opWait(2), opReauthWait(3), operational(4), rekeyWait(5), rekeyReauthWait(6)} MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the state of the indicated TEK FSM. The start(1) state indicates that FSM is in its initial state." ::= { wmanIf2SsPkmTekEntry 6 } wmanIf2SsPkmTekKeySequenceNumber OBJECT-TYPE SYNTAX Integer32 (0..3) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the most recent TEK key sequence number for this TEK FSM." REFERENCE "IEEE Std 802.16-2004; 11.9.5" ::= { wmanIf2SsPkmTekEntry 7 } wmanIf2SsPkmTekExpiresOld OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the actual clock time for expiration of the immediate predecessor of the most recent TEK for this FSM. If this FSM has only one TEK, then the value is the time of activation of this FSM." ::= { wmanIf2SsPkmTekEntry 8 } wmanIf2SsPkmTekExpiresNew OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the actual clock time for expiration of the most recent TEK for this FSM." ::= { wmanIf2SsPkmTekEntry 9 } wmanIf2SsPkmTekKeyRequests OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the SS has transmitted a Key Request message." ::= { wmanIf2SsPkmTekEntry 10 } wmanIf2SsPkmTekKeyReplies OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the SS has received a Key Reply message, including a message whose authentication failed." ::= { wmanIf2SsPkmTekEntry 11 } wmanIf2SsPkmTekKeyRejects OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the SS has received a Key Reject message, including a message whose authentication failed." ::= { wmanIf2SsPkmTekEntry 12 } wmanIf2SsPkmTekInvalids OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the SS has received a TEK Invalid message, including a message whose authentication failed." ::= { wmanIf2SsPkmTekEntry 13 } wmanIf2SsPkmTekAuthPends OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times an Authorization Pending (Auth Pend) event occurred in this FSM." ::= { wmanIf2SsPkmTekEntry 14 } wmanIf2SsPkmTekKeyRejectErrorCode OBJECT-TYPE SYNTAX INTEGER {none(1), unknown(2), unauthorizedSaid(4)} MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the enumerated description of the Error-Code in most recent Key Reject message received by the SS. This has value unknown(2) if the last Error-Code value was 0, and none(1) if no Key Reject message has been received since reboot." ::= { wmanIf2SsPkmTekEntry 15 } wmanIf2SsPkmTekKeyRejectErrorString OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the Display-String in most recent Key Reject message received by the SS. This is a zero length string if no Key Reject message has been received since reboot." ::= { wmanIf2SsPkmTekEntry 16 } wmanIf2SsPkmTekInvalidErrorCode OBJECT-TYPE SYNTAX INTEGER {none(1), unknown(2), invalidKeySequence(6)} MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the enumerated description of the Error-Code in most recent TEK Invalid message received by the SS. This has value unknown(2) if the last Error-Code value was 0, and none(1) if no TEK Invalid message has been received since reboot." ::= { wmanIf2SsPkmTekEntry 17 } wmanIf2SsPkmTekInvalidErrorString OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the Display-String in most recent TEK Invalid message received by the SS. This is a zero length string if no TEK Invalid message has been received since reboot." ::= { wmanIf2SsPkmTekEntry 18 } -- -- Table wmanIf2SsDeviceCertTable -- wmanIf2SsDeviceCertTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2SsDeviceCertEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the PKM device certificates for each SS wireless interface." ::= { wmanIf2SsPkmObjects 3 } wmanIf2SsDeviceCertEntry OBJECT-TYPE SYNTAX WmanIf2SsDeviceCertEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains the device certificate of one SS." INDEX { ifIndex } ::= { wmanIf2SsDeviceCertTable 1 } WmanIf2SsDeviceCertEntry ::= SEQUENCE { wmanIf2SsDeviceCert OCTET STRING, wmanIf2SsDeviceManufCert OCTET STRING} wmanIf2SsDeviceCert OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..65535)) MAX-ACCESS read-only STATUS current DESCRIPTION "The X509 DER-encoded subscriber station certificate." ::= { wmanIf2SsDeviceCertEntry 1 } wmanIf2SsDeviceManufCert OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..65535)) MAX-ACCESS read-only STATUS current DESCRIPTION "The X509 DER-encoded manufacturer certificate which is signed by the CA root authority certificate." ::= { wmanIf2SsDeviceCertEntry 2 } -- -- Subscriber station Notification Group -- wmanIf2SsNotificationObjects contains the SS SNMP Trap objects -- wmanIf2SsNotification OBJECT IDENTIFIER ::= { wmanIf2SsObjects 3 } wmanIf2SsTrapControl OBJECT IDENTIFIER ::= { wmanIf2SsNotification 1 } wmanIf2SsTrapDefinitions OBJECT IDENTIFIER ::= { wmanIf2SsNotification 2 } -- This object groups all NOTIFICATION-TYPE objects for SS. -- It is defined following RFC2758 sections 8.5 and 8.6 -- for the compatibility with SNMPv1. wmanIf2SsTrapPrefix OBJECT IDENTIFIER ::= { wmanIf2SsTrapDefinitions 0 } wmanIf2SsTrapControlRegister OBJECT-TYPE SYNTAX BITS {wmanIf2SsTlvUnknown(0), wmanIf2SsDynamicServiceFail(1), wmanIf2SsDhcpSuccess(2), wmanIf2SsRssiStatusChange(3)} MAX-ACCESS read-write STATUS current DESCRIPTION "The object is used to enable Subscriber Station traps. From left to right, the set bit indicates the corresponding Subscriber Station trap is enabled." ::= { wmanIf2SsTrapControl 1 } wmanIf2SsThresholdConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2SsThresholdConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains threshold objects that can be set to detect the threshold crossing events." ::= { wmanIf2SsTrapControl 2 } wmanIf2SsThresholdConfigEntry OBJECT-TYPE SYNTAX WmanIf2SsThresholdConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each Ss, and is indexed by ifIndex." INDEX { ifIndex } ::= { wmanIf2SsThresholdConfigTable 1 } WmanIf2SsThresholdConfigEntry ::= SEQUENCE { wmanIf2SsRssiLowThreshold Integer32, wmanIf2SsRssiHighThreshold Integer32} wmanIf2SsRssiLowThreshold OBJECT-TYPE SYNTAX Integer32 UNITS "dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "Low RSSI threshold for generating the RSSI alarm trap." ::= { wmanIf2SsThresholdConfigEntry 1 } wmanIf2SsRssiHighThreshold OBJECT-TYPE SYNTAX Integer32 UNITS "dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "High RSSI threshold for generating a trap to indicate the RSSI is restored." ::= { wmanIf2SsThresholdConfigEntry 2 } wmanIf2SsTlvUnknownTrap NOTIFICATION-TYPE OBJECTS {ifIndex, wmanIf2SsMacAddress, wmanIf2SsUnknownTlv} STATUS current DESCRIPTION "Event that notifies detection of unknown TLV during the TLV parsing process." ::= { wmanIf2SsTrapPrefix 1 } wmanIf2SsDynamicServiceFailTrap NOTIFICATION-TYPE OBJECTS {ifIndex, wmanIf2SsMacAddress, wmanIf2SsDynamicServiceType, wmanIf2SsDynamicServiceFailReason} STATUS current DESCRIPTION "An event to report the failure of a dynamic service operation happened during the dynamic services process and detected in the BS side." ::= { wmanIf2SsTrapPrefix 2 } wmanIf2SsDhcpSuccessTrap NOTIFICATION-TYPE OBJECTS {ifIndex, wmanIf2SsMacAddress} STATUS current DESCRIPTION "An event to report a successful Handshake to establish IP connectivity." ::= { wmanIf2SsTrapPrefix 3 } wmanIf2SsRssiStatusChangeTrap NOTIFICATION-TYPE OBJECTS {ifIndex, wmanIf2SsMacAddress, wmanIf2SsRssiStatus, wmanIf2SsRssiStatusInfo} STATUS current DESCRIPTION "An event to report that the downlink RSSI is below wmanIf2SsRssiLowThreshold, or above wmanIf2SsRssiHighThreshold after restore." ::= { wmanIf2SsTrapPrefix 4 } wmanIf2SsNotificationObjectsTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2SsNotificationObjectsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains SS notification objects that have been reported by the trap." ::= { wmanIf2SsTrapDefinitions 1 } wmanIf2SsNotificationObjectsEntry OBJECT-TYPE SYNTAX WmanIf2SsNotificationObjectsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each SS that has generated traps, and is indexed by ifIndex." INDEX { ifIndex } ::= { wmanIf2SsNotificationObjectsTable 1 } WmanIf2SsNotificationObjectsEntry ::= SEQUENCE { wmanIf2SsMacAddress MacAddress, wmanIf2SsUnknownTlv OCTET STRING, wmanIf2SsDynamicServiceType INTEGER, wmanIf2SsDynamicServiceFailReason OCTET STRING, wmanIf2SsRssiStatus INTEGER, wmanIf2SsRssiStatusInfo OCTET STRING} wmanIf2SsMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address of the SS generating the trap." ::= { wmanIf2SsNotificationObjectsEntry 1 } wmanIf2SsUnknownTlv OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..65535)) MAX-ACCESS read-only STATUS current DESCRIPTION "Indicating the value of the unknown TLV." ::= { wmanIf2SsNotificationObjectsEntry 2 } wmanIf2SsDynamicServiceType OBJECT-TYPE SYNTAX INTEGER {ssSfCreationReq(1), ssSfCreationRsp(2), ssSfCreationAck(3)} MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the dynamic service flow creation command type." ::= { wmanIf2SsNotificationObjectsEntry 3 } wmanIf2SsDynamicServiceFailReason OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the reason why the service flow creation has failed." ::= { wmanIf2SsNotificationObjectsEntry 4 } wmanIf2SsRssiStatus OBJECT-TYPE SYNTAX INTEGER {ssRssiAlarm(1), ssRssiNoAlarm(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "A RSSI alarm is generated if the RSSI is lower than wmanIf2SsRssiLowThreshold, or above wmanIf2SsRssiHighThreshold after alarm is restored." ::= { wmanIf2SsNotificationObjectsEntry 5 } wmanIf2SsRssiStatusInfo OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object provides additional information about RSSI alarm. It is implementation specific" ::= { wmanIf2SsNotificationObjectsEntry 6 } -- -- Subscriber station PHY Group -- wmanIf2SsPhy OBJECT IDENTIFIER ::= { wmanIf2SsObjects 5 } -- -- SS OFDM PHY objects -- wmanIf2SsOfdmPhy OBJECT IDENTIFIER ::= { wmanIf2SsPhy 1 } wmanIf2SsOfdmUplinkChannelTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2SsOfdmUplinkChannelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains UCD channel attributes, defining the transmission characteristics of uplink channels" REFERENCE "Table 349 and Table 352, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmPhy 1 } wmanIf2SsOfdmUplinkChannelEntry OBJECT-TYPE SYNTAX WmanIf2SsOfdmUplinkChannelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each uplink channel of multi-sector BS, and is indexed by BS ifIndex. An entry in this table exists for each ifEntry of BS with an ifType of propBWAp2Mp." INDEX { ifIndex } ::= { wmanIf2SsOfdmUplinkChannelTable 1 } WmanIf2SsOfdmUplinkChannelEntry ::= SEQUENCE { wmanIf2SsOfdmCtBasedResvTimeout INTEGER, wmanIf2SsOfdmBwReqOppSize INTEGER, wmanIf2SsOfdmRangReqOppSize INTEGER, wmanIf2SsOfdmUplinkCenterFreq Unsigned32, wmanIf2SsOfdmNumSubChReqRegionFull INTEGER, wmanIf2SsOfdmNumSymbolsReqRegionFull INTEGER, wmanIf2SsOfdmSubChFocusCtCode INTEGER, wmanIf2SsOfdmUpLinkChannelId INTEGER} wmanIf2SsOfdmCtBasedResvTimeout OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of UL-MAPs to receive before contention-based reservation is attempted again for the same connection." REFERENCE "Table 349, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmUplinkChannelEntry 1 } wmanIf2SsOfdmBwReqOppSize OBJECT-TYPE SYNTAX INTEGER (1..65535) UNITS "PS" MAX-ACCESS read-only STATUS current DESCRIPTION "Size (in units of PS) of PHY payload that SS may use to format and transmit a bandwidth request message in a contention request opportunity. The value includes all PHY overhead as well as allowance for the MAC data the message may hold." REFERENCE "Table 349, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmUplinkChannelEntry 2 } wmanIf2SsOfdmRangReqOppSize OBJECT-TYPE SYNTAX INTEGER (1..65535) UNITS "PS" MAX-ACCESS read-only STATUS current DESCRIPTION "Size (in units of PS) of PHY payload that SS may use to format and transmit a RNG-REQ message in a contention request opportunity. The value includes all PHY overhead as well as allowance for the MAC data the message may hold and the maxiumum SS/BS roundtrip propagation delay." REFERENCE "Table 349, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmUplinkChannelEntry 3 } wmanIf2SsOfdmUplinkCenterFreq OBJECT-TYPE SYNTAX Unsigned32 UNITS "kHz" MAX-ACCESS read-only STATUS current DESCRIPTION " Uplink center frequency (kHz)" REFERENCE "Table 349, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmUplinkChannelEntry 4 } wmanIf2SsOfdmNumSubChReqRegionFull OBJECT-TYPE SYNTAX INTEGER {oneSubchannel(0), twoSubchannels(1), fourSubchannels(2), eightSubchannels(3), sixteenSubchannels(4)} MAX-ACCESS read-only STATUS current DESCRIPTION "Number of subchannels used by each transmit opportunity when REQ Region-Full is allocated in subchannelization region." REFERENCE "Table 352, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmUplinkChannelEntry 5 } wmanIf2SsOfdmNumSymbolsReqRegionFull OBJECT-TYPE SYNTAX INTEGER (0..31) MAX-ACCESS read-only STATUS current DESCRIPTION "Number of OFDM symbols used by each transmit opportunity when REQ Region-Full is allocated in subchannelization region." REFERENCE "Table 352, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmUplinkChannelEntry 6 } wmanIf2SsOfdmSubChFocusCtCode OBJECT-TYPE SYNTAX INTEGER (0..8) MAX-ACCESS read-only STATUS current DESCRIPTION "Number of contention codes (CSE) that shall only be used to request a subchannelized allocation. Default value 0. Allowed values 0-8." REFERENCE "Table 352, in IEEE Std 802.16-2004" DEFVAL { 0 } ::= { wmanIf2SsOfdmUplinkChannelEntry 7 } wmanIf2SsOfdmUpLinkChannelId OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The identifier of the uplink channel to which this message refers." REFERENCE "Subclause 6.3.2.3.4. Table 16, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmUplinkChannelEntry 8 } wmanIf2SsOfdmDownlinkChannelTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2SsOfdmDownlinkChannelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains DCD channel attributes, defining the transmission characteristics of downlink channels" REFERENCE "Table 358, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmPhy 2 } wmanIf2SsOfdmDownlinkChannelEntry OBJECT-TYPE SYNTAX WmanIf2SsOfdmDownlinkChannelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each downlink channel of multi-sector BS, and is indexed by BS ifIndex. An entry in this table exists for each ifEntry of BS with an ifType of propBWAp2Mp." INDEX { ifIndex } ::= { wmanIf2SsOfdmDownlinkChannelTable 1 } WmanIf2SsOfdmDownlinkChannelEntry ::= SEQUENCE { wmanIf2SsOfdmBsEIRP INTEGER, wmanIf2SsOfdmChannelNumber WmanIf2ChannelNumber, wmanIf2SsOfdmTTG INTEGER, wmanIf2SsOfdmRTG INTEGER, wmanIf2SsOfdmInitRngMaxRSS INTEGER, wmanIf2SsOfdmDownlinkCenterFreq Unsigned32, wmanIf2SsOfdmBsId WmanIf2BsIdType, wmanIf2SsOfdmMacVersion WmanIf2MacVersion, wmanIf2SsOfdmFrameDurationCode INTEGER, wmanIf2SsOfdmDownLinkChannelId INTEGER} wmanIf2SsOfdmBsEIRP OBJECT-TYPE SYNTAX INTEGER (-32768..32767) UNITS "dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "The EIRP is the equivalent isotropic radiated power of the base station, which is computed for a simple single-antenna transmitter." REFERENCE "Table 358, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmDownlinkChannelEntry 1 } wmanIf2SsOfdmChannelNumber OBJECT-TYPE SYNTAX WmanIf2ChannelNumber MAX-ACCESS read-only STATUS current DESCRIPTION "Downlink channel number as defined in 8.5. Used for license-exempt operation only." REFERENCE "Table 358, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmDownlinkChannelEntry 2 } wmanIf2SsOfdmTTG OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Transmit / Receive Transition Gap." REFERENCE "Table 358, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmDownlinkChannelEntry 3 } wmanIf2SsOfdmRTG OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Receive / Transmit Transition Gap." REFERENCE "Table 358, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmDownlinkChannelEntry 4 } wmanIf2SsOfdmInitRngMaxRSS OBJECT-TYPE SYNTAX INTEGER (-32768..32767) UNITS "dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "Initial Ranging Max. equivalent isotropic received power at BS Signed in units of 1 dBm." REFERENCE "Table 358, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmDownlinkChannelEntry 5 } wmanIf2SsOfdmDownlinkCenterFreq OBJECT-TYPE SYNTAX Unsigned32 UNITS "kHz" MAX-ACCESS read-only STATUS current DESCRIPTION "Downlink center frequency (kHz)." REFERENCE "Table 358, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmDownlinkChannelEntry 6 } wmanIf2SsOfdmBsId OBJECT-TYPE SYNTAX WmanIf2BsIdType MAX-ACCESS read-only STATUS current DESCRIPTION "Base station ID." REFERENCE "Table 358, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmDownlinkChannelEntry 7 } wmanIf2SsOfdmMacVersion OBJECT-TYPE SYNTAX WmanIf2MacVersion MAX-ACCESS read-only STATUS current DESCRIPTION "This parameter specifies the version of 802.16 to which the message originator conforms." REFERENCE "Table 358, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmDownlinkChannelEntry 8 } wmanIf2SsOfdmFrameDurationCode OBJECT-TYPE SYNTAX INTEGER {duration2dot5ms(0), duration4ms(1), duration5ms(2), duration8ms(3), duration10ms(4), duration12dot5ms(5), duration20ms(6)} MAX-ACCESS read-only STATUS current DESCRIPTION "The duration of the frame. The frame duration code values are specified in Table 230." REFERENCE "Subclause 11.4.1, Table 230, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmDownlinkChannelEntry 9 } wmanIf2SsOfdmDownLinkChannelId OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The identifier of the downlink channel to which this message refers." REFERENCE "Subclause 6.3.2.3.1, Table 15, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmDownlinkChannelEntry 10 } wmanIf2SsOfdmUcdBurstProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2SsOfdmUcdBurstProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains UCD burst profiles for each uplink channel" REFERENCE "Table 356, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmPhy 3 } wmanIf2SsOfdmUcdBurstProfileEntry OBJECT-TYPE SYNTAX WmanIf2SsOfdmUcdBurstProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each UCD burst profile. This table is double indexed. The primary index is an ifIndex with an ifType of propBWAp2Mp. The secondary index is wmanIf2SsOfdmOfdmUcdBurstProfIndex." INDEX { ifIndex, wmanIf2SsOfdmUiucIndex } ::= { wmanIf2SsOfdmUcdBurstProfileTable 1 } WmanIf2SsOfdmUcdBurstProfileEntry ::= SEQUENCE { wmanIf2SsOfdmUiucIndex INTEGER, wmanIf2SsOfdmUcdFecCodeType WmanIf2OfdmFecCodeType, wmanIf2SsOfdmFocusCtPowerBoost INTEGER, wmanIf2SsOfdmUcdTcsEnable INTEGER} wmanIf2SsOfdmUiucIndex OBJECT-TYPE SYNTAX INTEGER (5 .. 12) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Uplink Interval Usage Code indicates the uplink burst profile in the UCD message, and is used along with ifIndex to identify an entry in the wmanIf2SsOfdmUcdBurstProfileTable." REFERENCE "Subclause 8.3.6.3.1, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmUcdBurstProfileEntry 1 } wmanIf2SsOfdmUcdFecCodeType OBJECT-TYPE SYNTAX WmanIf2OfdmFecCodeType MAX-ACCESS read-only STATUS current DESCRIPTION "Uplink FEC code type and modulation type" REFERENCE "Table 356, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmUcdBurstProfileEntry 2 } wmanIf2SsOfdmFocusCtPowerBoost OBJECT-TYPE SYNTAX INTEGER (0 .. 255) MAX-ACCESS read-only STATUS current DESCRIPTION "The power boost in dB of focused contention carriers, as described in 8.3.6.3.3." REFERENCE "Table 356, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmUcdBurstProfileEntry 3 } wmanIf2SsOfdmUcdTcsEnable OBJECT-TYPE SYNTAX INTEGER {tcsDisabled(0), tcsEnabled(1)} MAX-ACCESS read-only STATUS current DESCRIPTION "This parameter determines the transmission convergence sublayer, as described in 8.1.4.3, can be enabled on a per-burst basis for both uplink and downlink. through DIUC/UIUC messages." REFERENCE "Table 356, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmUcdBurstProfileEntry 4 } wmanIf2SsOfdmDcdBurstProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2SsOfdmDcdBurstProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each DCD burst profile. This table is double indexed. The primary index is an ifIndex with an ifType of propBWAp2Mp. The secondary index is wmanIf2SsOfdmDiucIndex." REFERENCE "Table 362, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmPhy 4 } wmanIf2SsOfdmDcdBurstProfileEntry OBJECT-TYPE SYNTAX WmanIf2SsOfdmDcdBurstProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each DCD burst profile. This table is double indexed. The primary index is an ifIndex with an ifType of propBWAp2Mp. The secondary index is wmanIf2SsOfdmDcdBurstProfIndex." INDEX { ifIndex, wmanIf2SsOfdmDiucIndex } ::= { wmanIf2SsOfdmDcdBurstProfileTable 1 } WmanIf2SsOfdmDcdBurstProfileEntry ::= SEQUENCE { wmanIf2SsOfdmDiucIndex INTEGER, wmanIf2SsOfdmDownlinkFrequency Unsigned32, wmanIf2SsOfdmDcdFecCodeType WmanIf2OfdmFecCodeType, wmanIf2SsOfdmDiucMandatoryExitThresh INTEGER, wmanIf2SsOfdmDiucMinEntryThresh INTEGER, wmanIf2SsOfdmTcsEnable INTEGER} wmanIf2SsOfdmDiucIndex OBJECT-TYPE SYNTAX INTEGER (1..11) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Downlink Interval Usage Code indicates the downlink burst profile in the DCD message, and is used along with ifIndex to identify an entry in the wmanIf2SsOfdmDcdBurstProfileTable." REFERENCE "Subclause 8.3.6.3.1, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmDcdBurstProfileEntry 1 } wmanIf2SsOfdmDownlinkFrequency OBJECT-TYPE SYNTAX Unsigned32 UNITS "kHz" MAX-ACCESS read-only STATUS current DESCRIPTION "Downlink Frequency (kHz)." REFERENCE "Table 362, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmDcdBurstProfileEntry 2 } wmanIf2SsOfdmDcdFecCodeType OBJECT-TYPE SYNTAX WmanIf2OfdmFecCodeType MAX-ACCESS read-only STATUS current DESCRIPTION "Downlink FEC code type and modulation type" REFERENCE "Table 362, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmDcdBurstProfileEntry 3 } wmanIf2SsOfdmDiucMandatoryExitThresh OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "DIUC mandatory exit threshold: 0 - 63.75 dB CINR at or below where this DIUC can no longer be used and where this change to a more robust DIUC is required in 0.25 dB units." REFERENCE "Table 362, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmDcdBurstProfileEntry 4 } wmanIf2SsOfdmDiucMinEntryThresh OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "DIUC minimum entry threshold: 0 - 63.75 dB The minimum CINR required to start using this DIUC when changing from a more robust DIUC is required, in 0.25 dB units." REFERENCE "Table 362, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmDcdBurstProfileEntry 5 } wmanIf2SsOfdmTcsEnable OBJECT-TYPE SYNTAX INTEGER {tcsDisabled (0), tcsEnabled (1)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether Transmission COnvergence Sublayer is enabled or disabled." REFERENCE "Table 362, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmDcdBurstProfileEntry 6 } -- -- SS OFDMA PHY objects -- wmanIf2SsOfdmaPhy OBJECT IDENTIFIER ::= { wmanIf2SsPhy 2 } wmanIf2SsOfdmaUplinkChannelTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2SsOfdmaUplinkChannelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains UCD channel attributes, defining the transmission characteristics of uplink channels" REFERENCE "Subclause 11.3.1, Table 349 and Table 353, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaPhy 1 } wmanIf2SsOfdmaUplinkChannelEntry OBJECT-TYPE SYNTAX WmanIf2SsOfdmaUplinkChannelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each uplink channel of multi-sector BS, and is indexed by BS ifIndex. An entry in this table exists for each ifEntry of BS with an ifType of propBWAp2Mp." INDEX { ifIndex } ::= { wmanIf2SsOfdmaUplinkChannelTable 1 } WmanIf2SsOfdmaUplinkChannelEntry ::= SEQUENCE { wmanIf2SsOfdmaCtBasedResvTimeout INTEGER, wmanIf2SsOfdmaBwReqOppSize INTEGER, wmanIf2SsOfdmaRangReqOppSize INTEGER, wmanIf2SsOfdmaUplinkCenterFreq Unsigned32, wmanIf2SsOfdmaInitRngCodes INTEGER, wmanIf2SsOfdmaPeriodicRngCodes INTEGER, wmanIf2SsOfdmaBWReqCodes INTEGER, wmanIf2SsOfdmaPerRngBackoffStart INTEGER, wmanIf2SsOfdmaPerRngBackoffEnd INTEGER, wmanIf2SsOfdmaStartOfRngCodes INTEGER, wmanIf2SsOfdmaPermutationBase INTEGER, wmanIf2SsOfdmaULAllocSubchBitmap OCTET STRING, wmanIf2SsOfdmaOptPermULAllocSubchBitmap OCTET STRING, wmanIf2SsOfdmaBandAMCAllocThreshold INTEGER, wmanIf2SsOfdmaBandAMCReleaseThreshold INTEGER, wmanIf2SsOfdmaBandAMCAllocTimer INTEGER, wmanIf2SsOfdmaBandAMCReleaseTimer INTEGER, wmanIf2SsOfdmaBandStatRepMAXPeriod INTEGER, wmanIf2SsOfdmaBandAMCRetryTimer INTEGER, wmanIf2SsOfdmaSafetyChAllocThreshold INTEGER, wmanIf2SsOfdmaSafetyChReleaseThreshold INTEGER, wmanIf2SsOfdmaSafetyChAllocTimer INTEGER, wmanIf2SsOfdmaSafetyChReleaseTimer INTEGER, wmanIf2SsOfdmaBinStatRepMAXPeriod INTEGER, wmanIf2SsOfdmaSafetyChaRetryTimer INTEGER, wmanIf2SsOfdmaHARQAackDelayULBurst INTEGER, wmanIf2SsOfdmaCQICHBandAMCTranaDelay INTEGER} wmanIf2SsOfdmaCtBasedResvTimeout OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of UL-MAPs to receive before contention-based reservation is attempted again for the same connection." REFERENCE "Table 349, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaUplinkChannelEntry 1 } wmanIf2SsOfdmaBwReqOppSize OBJECT-TYPE SYNTAX INTEGER (1..65535) UNITS "PS" MAX-ACCESS read-only STATUS current DESCRIPTION "Size (in units of PS) of PHY payload that SS may use to format and transmit a bandwidth request message in a contention request opportunity. The value includes all PHY overhead as well as allowance for the MAC data the message may hold." REFERENCE "Table 349, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaUplinkChannelEntry 2 } wmanIf2SsOfdmaRangReqOppSize OBJECT-TYPE SYNTAX INTEGER (1..65535) UNITS "PS" MAX-ACCESS read-only STATUS current DESCRIPTION "Size (in units of PS) of PHY payload that SS may use to format and transmit a RNG-REQ message in a contention request opportunity. The value includes all PHY overhead as well as allowance for the MAC data the message may hold and the maxiumum SS/BS roundtrip propagation delay." REFERENCE "Table 349, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaUplinkChannelEntry 3 } wmanIf2SsOfdmaUplinkCenterFreq OBJECT-TYPE SYNTAX Unsigned32 UNITS "kHz" MAX-ACCESS read-only STATUS current DESCRIPTION " Uplink center frequency (kHz)" REFERENCE "Table 349, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaUplinkChannelEntry 4 } wmanIf2SsOfdmaInitRngCodes OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Number of initial ranging CDMA codes. Possible values are 0..255. The total number of wmanIf2SsOfdmaInitRngCodes, wmanIf2SsOfdmaPeriodicRngCodes and wmanIf2SsOfdmaBWReqCodes shall be equal or less than 256." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16-2004" DEFVAL { 30 } ::= { wmanIf2SsOfdmaUplinkChannelEntry 5 } wmanIf2SsOfdmaPeriodicRngCodes OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Number of periodic ranging CDMA codes. Possible values are 0..255. The total number of wmanIf2SsOfdmaInitRngCodes, wmanIf2SsOfdmaPeriodicRngCodes and wmanIf2SsOfdmaBWReqCodes shall be equal or less than 256." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16-2004" DEFVAL { 30 } ::= { wmanIf2SsOfdmaUplinkChannelEntry 6 } wmanIf2SsOfdmaBWReqCodes OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Number of bandwidth request codes. Possible values are 0..255. The total number of wmanIf2SsOfdmaInitRngCodes, wmanIf2SsOfdmaPeriodicRngCodes and wmanIf2SsOfdmaBWReqCodes shall be equal or less than 256." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16-2004" DEFVAL { 30 } ::= { wmanIf2SsOfdmaUplinkChannelEntry 7 } wmanIf2SsOfdmaPerRngBackoffStart OBJECT-TYPE SYNTAX INTEGER (0..15) MAX-ACCESS read-only STATUS current DESCRIPTION "Initial backoff window size for periodic ranging contention, expressed as a power of 2." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16-2004" DEFVAL { 0 } ::= { wmanIf2SsOfdmaUplinkChannelEntry 8 } wmanIf2SsOfdmaPerRngBackoffEnd OBJECT-TYPE SYNTAX INTEGER (0 .. 15) MAX-ACCESS read-only STATUS current DESCRIPTION "Final backoff window size for periodic ranging contention, expressed as a power of 2." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16-2004" DEFVAL { 15 } ::= { wmanIf2SsOfdmaUplinkChannelEntry 9 } wmanIf2SsOfdmaStartOfRngCodes OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the starting number, S, of the group of codes used for this uplink.All the ranging codes used on this uplink will be between S and ((S+N+M+L) mod 256). Where, N is the number of initial-ranging codes M is the number of periodic-ranging codes L is the number of bandwidth-request codes The range of values is 0 S255" REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16-2004" DEFVAL { 0 } ::= { wmanIf2SsOfdmaUplinkChannelEntry 10 } wmanIf2SsOfdmaPermutationBase OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Determines the UL_IDcell parameter for the subcarrier permutation to be used on this uplink channel" REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16-2004" DEFVAL { 0 } ::= { wmanIf2SsOfdmaUplinkChannelEntry 11 } wmanIf2SsOfdmaULAllocSubchBitmap OBJECT-TYPE SYNTAX OCTET STRING (SIZE (9)) MAX-ACCESS read-only STATUS current DESCRIPTION "This is a bitmap describing the sub-channels allocated to the segment in the UL, when using the uplink PUSC permutation. The LSB of the first byte shall corrspond to subchannel 0. For any bit that is not set, the corresponding subchannel shall not be used by the SS on that segment" REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaUplinkChannelEntry 12 } wmanIf2SsOfdmaOptPermULAllocSubchBitmap OBJECT-TYPE SYNTAX OCTET STRING (SIZE (13)) MAX-ACCESS read-only STATUS current DESCRIPTION "This is a bitmap describing the sub-channels allocated to the segment in the UL, when using the uplink optional PUSC permutation (see 8.4.6.2.5 in IEEE Std 802.16-2004). The LSB of the first byte shall correspond to subchannel 0. For any bit that is not set, the corresponding subchannel shall not be used by the SS on that segment" REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaUplinkChannelEntry 13 } wmanIf2SsOfdmaBandAMCAllocThreshold OBJECT-TYPE SYNTAX INTEGER (0 .. 255) UNITS "dB" MAX-ACCESS read-only STATUS current DESCRIPTION "This object defines the OFDMA band AMC allocation threshold." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaUplinkChannelEntry 14 } wmanIf2SsOfdmaBandAMCReleaseThreshold OBJECT-TYPE SYNTAX INTEGER (0 .. 255) UNITS "dB" MAX-ACCESS read-only STATUS current DESCRIPTION "This object defines the OFDMA band AMC release threshold." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaUplinkChannelEntry 15 } wmanIf2SsOfdmaBandAMCAllocTimer OBJECT-TYPE SYNTAX INTEGER (0 .. 255) UNITS "Frame" MAX-ACCESS read-only STATUS current DESCRIPTION "This object defines the OFDMA band AMC allocation timer." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaUplinkChannelEntry 16 } wmanIf2SsOfdmaBandAMCReleaseTimer OBJECT-TYPE SYNTAX INTEGER (0 .. 255) UNITS "Frame" MAX-ACCESS read-only STATUS current DESCRIPTION "This object defines the OFDMA band AMC release timer." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaUplinkChannelEntry 17 } wmanIf2SsOfdmaBandStatRepMAXPeriod OBJECT-TYPE SYNTAX INTEGER (0 .. 255) UNITS "Frame" MAX-ACCESS read-only STATUS current DESCRIPTION "This object defines the OFDMA band status reporting maximum period." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaUplinkChannelEntry 18 } wmanIf2SsOfdmaBandAMCRetryTimer OBJECT-TYPE SYNTAX INTEGER (0 .. 255) UNITS "Frame" MAX-ACCESS read-only STATUS current DESCRIPTION "This object defines the OFDMA band AMC retry timer." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaUplinkChannelEntry 19 } wmanIf2SsOfdmaSafetyChAllocThreshold OBJECT-TYPE SYNTAX INTEGER (0 .. 255) UNITS "dB" MAX-ACCESS read-only STATUS current DESCRIPTION "This object defines the OFDMA safety channel allocation threshold." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaUplinkChannelEntry 20 } wmanIf2SsOfdmaSafetyChReleaseThreshold OBJECT-TYPE SYNTAX INTEGER (0 .. 255) UNITS "dB" MAX-ACCESS read-only STATUS current DESCRIPTION "This object defines the OFDMA safety channel release threshold." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaUplinkChannelEntry 21 } wmanIf2SsOfdmaSafetyChAllocTimer OBJECT-TYPE SYNTAX INTEGER (0 .. 255) UNITS "Frame" MAX-ACCESS read-only STATUS current DESCRIPTION "This object defines the OFDMA safety channel allocation timer." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaUplinkChannelEntry 22 } wmanIf2SsOfdmaSafetyChReleaseTimer OBJECT-TYPE SYNTAX INTEGER (0 .. 255) UNITS "Frame" MAX-ACCESS read-only STATUS current DESCRIPTION "This object defines the OFDMA safety channel release timer." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaUplinkChannelEntry 23 } wmanIf2SsOfdmaBinStatRepMAXPeriod OBJECT-TYPE SYNTAX INTEGER (0 .. 255) UNITS "Frame" MAX-ACCESS read-only STATUS current DESCRIPTION "This object defines the OFDMA bin status reporting maximum period." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaUplinkChannelEntry 24 } wmanIf2SsOfdmaSafetyChaRetryTimer OBJECT-TYPE SYNTAX INTEGER (0 .. 255) UNITS "Frame" MAX-ACCESS read-only STATUS current DESCRIPTION "This object defines the OFDMA safety channel retry timer." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaUplinkChannelEntry 25 } wmanIf2SsOfdmaHARQAackDelayULBurst OBJECT-TYPE SYNTAX INTEGER {oneframeoffset(1), twoframesoffset(2), threeframesoffset(3)} MAX-ACCESS read-only STATUS current DESCRIPTION "This object defines the OFDMA H-ARQ ACK delay for UL burst. 1 = one frame offset 2 = two frames offset 3 = three frames offset" REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaUplinkChannelEntry 26 } wmanIf2SsOfdmaCQICHBandAMCTranaDelay OBJECT-TYPE SYNTAX INTEGER (0 .. 255) UNITS "Frame" MAX-ACCESS read-only STATUS current DESCRIPTION "This object defines the OFDMA CQICH band AMC transition delay." REFERENCE "Subclause 11.3.1, Table 353, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaUplinkChannelEntry 27 } wmanIf2SsOfdmaDownlinkChannelTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2SsOfdmaDownlinkChannelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains DCD channel attributes, defining the transmission characteristics of downlink channels" REFERENCE "Subclause 11.4.1, Table 358, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaPhy 2 } wmanIf2SsOfdmaDownlinkChannelEntry OBJECT-TYPE SYNTAX WmanIf2SsOfdmaDownlinkChannelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each downlink channel of multi-sector BS, and is indexed by BS ifIndex. An entry in this table exists for each ifEntry of BS with an ifType of propBWAp2Mp." INDEX { ifIndex } ::= { wmanIf2SsOfdmaDownlinkChannelTable 1 } WmanIf2SsOfdmaDownlinkChannelEntry ::= SEQUENCE { wmanIf2SsOfdmaBsEIRP INTEGER, wmanIf2SsOfdmaChannelNumber WmanIf2ChannelNumber, wmanIf2SsOfdmaTTG INTEGER, wmanIf2SsOfdmaRTG INTEGER, wmanIf2SsOfdmaInitRngMaxRSS INTEGER, wmanIf2SsOfdmaDownlinkCenterFreq Unsigned32, wmanIf2SsOfdmaBsId WmanIf2BsIdType, wmanIf2SsOfdmaMacVersion WmanIf2MacVersion, wmanIf2SsOfdmaFrameDurationCode INTEGER, wmanIf2SsOfdmaSizeCqichIdField INTEGER, wmanIf2SsOfdmaHARQAackDelayBurst INTEGER} wmanIf2SsOfdmaBsEIRP OBJECT-TYPE SYNTAX INTEGER (-32768..32767) UNITS "dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "The EIRP is the equivalent isotropic radiated power of the base station, which is computed for a simple single-antenna transmitter." REFERENCE "Subclause 11.4.1, Table 358, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaDownlinkChannelEntry 1 } wmanIf2SsOfdmaChannelNumber OBJECT-TYPE SYNTAX WmanIf2ChannelNumber MAX-ACCESS read-only STATUS current DESCRIPTION "Downlink channel number as defined in 8.5. Used for license-exempt operation only." REFERENCE "Subclause 11.4.1, Table 358, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaDownlinkChannelEntry 2 } wmanIf2SsOfdmaTTG OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Transmit / Receive Transition Gap." REFERENCE "Subclause 11.4.1, Table 358, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaDownlinkChannelEntry 3 } wmanIf2SsOfdmaRTG OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Receive / Transmit Transition Gap." REFERENCE "Subclause 11.4.1, Table 358, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaDownlinkChannelEntry 4 } wmanIf2SsOfdmaInitRngMaxRSS OBJECT-TYPE SYNTAX INTEGER (-32768..32767) UNITS "dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "Initial Ranging Max. equivalent isotropic received power at BS Signed in units of 1 dBm." REFERENCE "Subclause 11.4.1, Table 358, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaDownlinkChannelEntry 5 } wmanIf2SsOfdmaDownlinkCenterFreq OBJECT-TYPE SYNTAX Unsigned32 UNITS "kHz" MAX-ACCESS read-only STATUS current DESCRIPTION "Downlink center frequency (kHz)." REFERENCE "Subclause 11.4.1, Table 358, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaDownlinkChannelEntry 6 } wmanIf2SsOfdmaBsId OBJECT-TYPE SYNTAX WmanIf2BsIdType MAX-ACCESS read-only STATUS current DESCRIPTION "Base station ID." REFERENCE "Subclause 11.4.1, Table 358, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaDownlinkChannelEntry 7 } wmanIf2SsOfdmaMacVersion OBJECT-TYPE SYNTAX WmanIf2MacVersion MAX-ACCESS read-only STATUS current DESCRIPTION "This parameter specifies the version of 802.16 to which the message originator conforms." REFERENCE "Subclause 11.4.1, Table 358, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaDownlinkChannelEntry 8 } wmanIf2SsOfdmaFrameDurationCode OBJECT-TYPE SYNTAX INTEGER {aASGap(0), duration2ms(1), duration2dot5ms(2), duration4ms(3), duration5ms(4), duration8ms(5), duration10ms(6), duration12dot5ms(7), duration20ms(8)} MAX-ACCESS read-only STATUS current DESCRIPTION "The duration of the frame. The frame duration code values are specified in Table 232 in IEEE Std 802.16-2004." REFERENCE "Subclause 11.4.1, Table 358, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaDownlinkChannelEntry 9 } wmanIf2SsOfdmaSizeCqichIdField OBJECT-TYPE SYNTAX INTEGER {threebits(1), fourbits(2), fivebits(3), sixbits(4), sevenbits(5), eightbits(6), ninebits(7)} MAX-ACCESS read-only STATUS current DESCRIPTION "This object defines the size of CQICH ID field. 0 = Reserved 1 = 3 bits 2 = 4 bits 3 = 5 bits 4 = 6 bits 5 = 7 bits 6 = 8 bits 7 = 9 bits 8...255 = Reserved" REFERENCE "Subclause 11.3.1, Table 358, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaDownlinkChannelEntry 10 } wmanIf2SsOfdmaHARQAackDelayBurst OBJECT-TYPE SYNTAX INTEGER {oneframeoffset(1), twoframesoffset(2), threeframesoffset(3)} MAX-ACCESS read-only STATUS current DESCRIPTION "This object defines the OFDMA H-ARQ ACK delay for DL burst. 1 = one frame offset 2 = two frames offset 3 = three frames offset" REFERENCE "Subclause 11.3.1, Table 358, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaDownlinkChannelEntry 11 } wmanIf2SsOfdmaUcdBurstProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2SsOfdmaUcdBurstProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains UCD burst profiles for each uplink channel" REFERENCE "Subclause 11.3.1.1, Table 288 and Table 357, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaPhy 3 } wmanIf2SsOfdmaUcdBurstProfileEntry OBJECT-TYPE SYNTAX WmanIf2SsOfdmaUcdBurstProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each UCD burst profile. This table is double indexed. The primary index is an ifIndex with an ifType of propBWAp2Mp. The secondary index is wmanIf2SsOfdmaUiucIndex." INDEX { ifIndex, wmanIf2SsOfdmaUiucIndex } ::= { wmanIf2SsOfdmaUcdBurstProfileTable 1 } WmanIf2SsOfdmaUcdBurstProfileEntry ::= SEQUENCE { wmanIf2SsOfdmaUiucIndex INTEGER, wmanIf2SsOfdmaUcdFecCodeType WmanIf2OfdmaFecCodeType, wmanIf2SsOfdmaRangingDataRatio INTEGER, wmanIf2SsOfdmaNorCOverNOverride OCTET STRING} wmanIf2SsOfdmaUiucIndex OBJECT-TYPE SYNTAX INTEGER (1 .. 10) MAX-ACCESS read-only STATUS current DESCRIPTION "The Uplink Interval Usage Code indicates the uplink burst profile in the UCD message, and is used along with ifIndex to identify an entry in the wmanIf2SsOfdmaUcdBurstProfileTable." REFERENCE "Subclause 8.4.5.4.1, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaUcdBurstProfileEntry 1 } wmanIf2SsOfdmaUcdFecCodeType OBJECT-TYPE SYNTAX WmanIf2OfdmaFecCodeType MAX-ACCESS read-only STATUS current DESCRIPTION "Uplink FEC code type and modulation type" REFERENCE "Subclause 11.3.1.1, Table 357, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaUcdBurstProfileEntry 2 } wmanIf2SsOfdmaRangingDataRatio OBJECT-TYPE SYNTAX INTEGER (0 .. 255) MAX-ACCESS read-only STATUS current DESCRIPTION "Reducing factor in units of 1 dB, between the power used for this burst and power should be used for CDMA Ranging." REFERENCE "Subclause 11.3.1.1, Table 357, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaUcdBurstProfileEntry 3 } wmanIf2SsOfdmaNorCOverNOverride OBJECT-TYPE SYNTAX OCTET STRING (SIZE (5)) MAX-ACCESS read-only STATUS current DESCRIPTION "This is a list of numbers, where each number is encoded by one nibble, and interpeted as a signed integer. The nibbles correspond in order to the list define by Table 334 in IEEE Std 802.16-2004 starting from the second line, such that the LS nibble of the first byte corresponds to the second line in the table. The number encoded by each nibble represents the difference in normalized C/N relative to the previous line in the table" REFERENCE "Subclause 11.3.1.1, Table 357, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaUcdBurstProfileEntry 4 } wmanIf2SsOfdmaDcdBurstProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2SsOfdmaDcdBurstProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each DCD burst profile. This table is double indexed. The primary index is an ifIndex with an ifType of propBWAp2Mp. The secondary index is wmanIf2SsOfdmaDiucIndex." ::= { wmanIf2SsOfdmaPhy 4 } wmanIf2SsOfdmaDcdBurstProfileEntry OBJECT-TYPE SYNTAX WmanIf2SsOfdmaDcdBurstProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each DCD burst profile, and is double indexed. The primary index is an ifIndex with an ifType of propBWAp2Mp. The secondary index is wmanIf2SsOfdmaDiucIndex." INDEX { ifIndex, wmanIf2SsOfdmaDiucIndex } ::= { wmanIf2SsOfdmaDcdBurstProfileTable 1 } WmanIf2SsOfdmaDcdBurstProfileEntry ::= SEQUENCE { wmanIf2SsOfdmaDiucIndex INTEGER, wmanIf2SsOfdmaDownlinkFrequency Unsigned32, wmanIf2SsOfdmaDcdFecCodeType WmanIf2OfdmaFecCodeType, wmanIf2SsOfdmaDiucMandatoryExitThresh INTEGER, wmanIf2SsOfdmaDiucMinEntryThresh INTEGER} wmanIf2SsOfdmaDiucIndex OBJECT-TYPE SYNTAX INTEGER (0 .. 12) MAX-ACCESS read-only STATUS current DESCRIPTION "The Downlink Interval Usage Code indicates the downlink burst profile in the DCD message, and is used along with ifIndex to identify an entry in the wmanIf2SsOfdmaDcdBurstProfileTable." REFERENCE "Subclause 8.4.5.3.1, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaDcdBurstProfileEntry 1 } wmanIf2SsOfdmaDownlinkFrequency OBJECT-TYPE SYNTAX Unsigned32 UNITS "kHz" MAX-ACCESS read-only STATUS current DESCRIPTION "Downlink Frequency (kHz)." REFERENCE "Subclause 11.4.2, Table 359, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaDcdBurstProfileEntry 2 } wmanIf2SsOfdmaDcdFecCodeType OBJECT-TYPE SYNTAX WmanIf2OfdmaFecCodeType MAX-ACCESS read-only STATUS current DESCRIPTION "Downlink FEC code type and modulation type" REFERENCE "Subclause 11.4.2, Table 363, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaDcdBurstProfileEntry 3 } wmanIf2SsOfdmaDiucMandatoryExitThresh OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "DIUC mandatory exit threshold: 0 - 63.75 dB CINR at or below where this DIUC can no longer be used and where this change to a more robust DIUC is required in 0.25 dB units." REFERENCE "Subclause 11.4.2, Table 363, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaDcdBurstProfileEntry 4 } wmanIf2SsOfdmaDiucMinEntryThresh OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "DIUC minimum entry threshold: 0 - 63.75 dB The minimum CINR required to start using this DIUC when changing from a more robust DIUC is required, in 0.25 dB units." REFERENCE "Subclause 11.4.2, Table 363, in IEEE Std 802.16-2004" ::= { wmanIf2SsOfdmaDcdBurstProfileEntry 5 } -- -- Common object group – containing common tables and objects to be -- implemented in both Base Station and Subscriber Station -- -- wmanIf2CmnPacketCs contain the Packet Convergence Sublayer objects -- that are common to both Base Station and Subscriber Station -- wmanIf2CmnPacketCs OBJECT IDENTIFIER ::= { wmanIf2CommonObjects 1 } wmanIf2CmnClassifierRuleTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2CmnClassifierRuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains packet classifier rules associated with service flows." ::= { wmanIf2CmnPacketCs 1 } wmanIf2CmnClassifierRuleEntry OBJECT-TYPE SYNTAX WmanIf2CmnClassifierRuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each packet classifier rule, and is indexed by ifIndex, wmanIf2CmnCpsSfId, and wmanIf2CmnClassifierRuleIndex. ifIndex is associated with the BS sector. wmanIf2CmnCpsSfId identifies the service flow, and wmanIf2CmnClassifierRuleIndex identifies the packet classifier rule." INDEX { ifIndex, wmanIf2CmnCpsSfId, wmanIf2CmnClassifierRuleIndex } ::= { wmanIf2CmnClassifierRuleTable 1 } WmanIf2CmnClassifierRuleEntry::= SEQUENCE { wmanIf2CmnClassifierRuleIndex Unsigned32, wmanIf2CmnClassifierRulePriority INTEGER, wmanIf2CmnClassifierRuleIpTosLow INTEGER, wmanIf2CmnClassifierRuleIpTosHigh INTEGER, wmanIf2CmnClassifierRuleIpTosMask INTEGER, wmanIf2CmnClassifierRuleIpProtocol Integer32, wmanIf2CmnClassifierRuleIpSourceAddr InetAddress, wmanIf2CmnClassifierRuleIpSourceMask InetAddress, wmanIf2CmnClassifierRuleIpDestAddr InetAddress, wmanIf2CmnClassifierRuleIpDestMask InetAddress, wmanIf2CmnClassifierRuleSourcePortStart Integer32, wmanIf2CmnClassifierRuleSourcePortEnd Integer32, wmanIf2CmnClassifierRuleDestPortStart Integer32, wmanIf2CmnClassifierRuleDestPortEnd Integer32, wmanIf2CmnClassifierRuleDestMacAddr MacAddress, wmanIf2CmnClassifierRuleDestMacMask MacAddress, wmanIf2CmnClassifierRuleSourceMacAddr MacAddress, wmanIf2CmnClassifierRuleSourceMacMask MacAddress, wmanIf2CmnClassifierRuleEnetProtocolType INTEGER, wmanIf2CmnClassifierRuleEnetProtocol Integer32, wmanIf2CmnClassifierRuleUserPriLow Integer32, wmanIf2CmnClassifierRuleUserPriHigh Integer32, wmanIf2CmnClassifierRuleVlanId Integer32, wmanIf2CmnClassifierRuleState INTEGER, wmanIf2CmnClassifierRulePkts Counter64, wmanIf2CmnClassifierRuleIpv6FlowLabel WmanIf2Ipv6FlowLabel, wmanIf2CmnClassifierRuleBitMap WmanIf2ClassifierBitMap } wmanIf2CmnClassifierRuleIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index is assigned to each classifier in the classifiers table" ::= { wmanIf2CmnClassifierRuleEntry 1 } wmanIf2CmnClassifierRulePriority OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The value specifies the order of evaluation of the classifiers. The higher the value the higher the priority. The value of 0 is used as default in provisioned service flows classifiers. The default value of 64 is used for dynamic service flow classifiers. If the referenced parameter is not present in a classifier , this object reports the default value as defined above" REFERENCE "Subclause 11.13.19.3.4.1 in IEEE Std 802.16-2004" DEFVAL { 0 } ::= { wmanIf2CmnClassifierRuleEntry 2 } wmanIf2CmnClassifierRuleIpTosLow OBJECT-TYPE SYNTAX INTEGER (0 .. 255) MAX-ACCESS read-only STATUS current DESCRIPTION "The low value of a range of TOS byte values. If the referenced parameter is not present in a classifier, this object reports the value of 0." REFERENCE "Subclause 11.13.19.3.4.2 in IEEE Std 802.16-2004" ::= { wmanIf2CmnClassifierRuleEntry 3 } wmanIf2CmnClassifierRuleIpTosHigh OBJECT-TYPE SYNTAX INTEGER (0 .. 255) MAX-ACCESS read-only STATUS current DESCRIPTION "The 8-bit high value of a range of TOS byte values. If the referenced parameter is not present in a classifier , this object reports the value of 0." REFERENCE "Subclause 11.13.19.3.4.2 in IEEE Std 802.16-2004" ::= { wmanIf2CmnClassifierRuleEntry 4 } wmanIf2CmnClassifierRuleIpTosMask OBJECT-TYPE SYNTAX INTEGER (0 .. 255) MAX-ACCESS read-only STATUS current DESCRIPTION "The mask value is bitwise ANDed with TOS byte in an IP packet and this value is used for the range checking of TosLow and TosHigh. If the referenced parameter is not present in a classifier, this object reports the value of 0." REFERENCE "Subclause 11.13.19.3.4.2 in IEEE Std 802.16-2004" ::= { wmanIf2CmnClassifierRuleEntry 5 } wmanIf2CmnClassifierRuleIpProtocol OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the value of the IP Protocol field required for IP packets to match this rule. If the referenced parameter is not present in a classifier, this object reports the value of 0." REFERENCE "Subclause 11.13.19.3.4.3 in IEEE Std 802.16-2004" ::= { wmanIf2CmnClassifierRuleEntry 6 } wmanIf2CmnClassifierRuleIpSourceAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the value of the IP Source Address required for packets to match this rule. An IP packet matches the rule when the packet ip source address bitwise ANDed with the wmanIf2CmnClassifierRuleIpSourceMask value equals the wmanIf2CmnClassifierRuleIpSourceAddr value. If the referenced parameter is not present in a classifier , this object reports the value of 0.0.0.0." REFERENCE "Subclause 11.13.19.3.4.4 in IEEE Std 802.16-2004" ::= { wmanIf2CmnClassifierRuleEntry 7 } wmanIf2CmnClassifierRuleIpSourceMask OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies which bits of a packet's IP Source Address that are compared to match this rule. An IP packet matches the rule when the packet source address bitwise ANDed with the wmanIf2CmnClassifierRuleIpSourceMask value equals the wmanIf2CmnClassifierRuleIpSourceAddr value. If the referenced parameter is not present in a classifier , this object reports the value of 0.0.0.0." REFERENCE "Subclause 11.13.19.3.4.4 in IEEE Std 802.16-2004" ::= { wmanIf2CmnClassifierRuleEntry 8 } wmanIf2CmnClassifierRuleIpDestAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the value of the IP Destination Address required for packets to match this rule. An IP packet matches the rule when the packet IP destination address bitwise ANDed with the wmanIf2CmnClassifierRuleIpDestMask value equals the wmanIf2CmnClassifierRuleIpDestAddr value. If the referenced parameter is not present in a classifier, this object reports the value of 0.0.0.0." REFERENCE "Subclause 11.13.19.3.4.5 in IEEE Std 802.16-2004" ::= { wmanIf2CmnClassifierRuleEntry 9 } wmanIf2CmnClassifierRuleIpDestMask OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies which bits of a packet's IP Destination Address that are compared to match this rule. An IP packet matches the rule when the packet destination address bitwise ANDed with the wmanIf2CmnClassifierRuleIpDestMask value equals the wmanIf2CmnClassifierRuleIpDestAddr value. If the referenced parameter is not present in a classifier , this object reports the value of 0.0.0.0." REFERENCE "Subclause 11.13.19.3.4.5 in IEEE Std 802.16-2004" ::= { wmanIf2CmnClassifierRuleEntry 10 } wmanIf2CmnClassifierRuleSourcePortStart OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the low end inclusive range of TCP/UDP source port numbers to which a packet is compared . This object is irrelevant for non-TCP/UDP IP packets. If the referenced parameter is not present in a classifier, this object reports the value of 0." REFERENCE "Subclause 11.13.19.3.4.6 in IEEE Std 802.16-2004" ::= { wmanIf2CmnClassifierRuleEntry 11 } wmanIf2CmnClassifierRuleSourcePortEnd OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the high end inclusive range of TCP/UDP source port numbers to which a packet is compared. This object is irrelevant for non-TCP/UDP IP packets. If the referenced parameter is not present in a classifier, this object reports the value of 65535." REFERENCE "Subclause 11.13.19.3.4.6 in IEEE Std 802.16-2004" ::= { wmanIf2CmnClassifierRuleEntry 12 } wmanIf2CmnClassifierRuleDestPortStart OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the low end inclusive range of TCP/UDP destination port numbers to which a packet is compared. If the referenced parameter is not present in a classifier, this object reports the value of 0." REFERENCE "Subclause 11.13.19.3.4.7 in IEEE Std 802.16-2004" ::= { wmanIf2CmnClassifierRuleEntry 13 } wmanIf2CmnClassifierRuleDestPortEnd OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the high end inclusive range of TCP/UDP destination port numbers to which a packet is compared. If the referenced parameter is not present in a classifier, this object reports the value of 65535." REFERENCE "Subclause 11.13.19.3.4.7 in IEEE Std 802.16-2004" ::= { wmanIf2CmnClassifierRuleEntry 14 } wmanIf2CmnClassifierRuleDestMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "An Ethernet packet matches an entry when its destination MAC address bitwise ANDed with wmanIf2CmnClassifierRuleDestMacMask equals the value of wmanIf2CmnClassifierRuleDestMacAddr. If the referenced parameter is not present in a classifier, this object reports the value of '000000000000'H." REFERENCE "Subclause 11.13.19.3.4.8 in IEEE Std 802.16-2004" ::= { wmanIf2CmnClassifierRuleEntry 15 } wmanIf2CmnClassifierRuleDestMacMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "An Ethernet packet matches an entry when its destination MAC address bitwise ANDed with wmanIf2CmnClassifierRuleDestMacMask equals the value of wmanIf2CmnClassifierRuleDestMacAddr. If the referenced parameter is not present in a classifier, this object reports the value of '000000000000'H." REFERENCE "Subclause 11.13.19.3.4.8 in IEEE Std 802.16-2004" ::= { wmanIf2CmnClassifierRuleEntry 16 } wmanIf2CmnClassifierRuleSourceMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "An Ethernet packet matches this entry when its source MAC address bitwise ANDed with wmanIf2CmnClassifierRuleSourceMacMask equals the value of wmanIf2CmnClassifierRuleSourceMacAddr. If the referenced parameter is not present in a classifier, this object reports the value of '000000000000'H." REFERENCE "Subclause 11.13.19.3.4.9 in IEEE Std 802.16-2004" ::= { wmanIf2CmnClassifierRuleEntry 17 } wmanIf2CmnClassifierRuleSourceMacMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "An Ethernet packet matches an entry when its destination MAC address bitwise ANDed with wmanIf2CmnClassifierRuleSourceMacMask equals the value of wmanIf2CmnClassifierRuleSourceMacAddr. If the referenced parameter is not present in a classifier, this object reports the value of '000000000000'H." REFERENCE "Subclause 11.13.19.3.4.9 in IEEE Std 802.16-2004" ::= { wmanIf2CmnClassifierRuleEntry 18 } wmanIf2CmnClassifierRuleEnetProtocolType OBJECT-TYPE SYNTAX INTEGER {none(0), ethertype(1), dsap(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the format of the layer 3 protocol id in the Ethernet packet. A value of none(0) means that the rule does not use the layer 3 protocol type as a matching criteria. A value of ethertype(1) means that the rule applies only to frames which contains an EtherType value. Ethertype values are contained in packets using the Dec-Intel-Xerox (DIX) encapsulation or the RFC1042 Sub-Network Access Protocol (SNAP) encapsulation formats. A value of dsap(2) means that the rule applies only to frames using the IEEE802.3 encapsulation format with a Destination Service Access Point (DSAP) other than 0xAA (which is reserved for SNAP). If the Ethernet frame contains an 802.1P/Q Tag header (i.e. EtherType 0x8100), this object applies to the embedded EtherType field within the 802.1P/Q header. If the referenced parameter is not present in a classifier, this object reports the value of 0." REFERENCE "Subclause 11.13.19.3.4.10 in IEEE Std 802.16-2004" ::= { wmanIf2CmnClassifierRuleEntry 19 } wmanIf2CmnClassifierRuleEnetProtocol OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "If wmanIf2CmnClassifierRuleEnetProtocolType is none(0), this object is ignored when considering whether a packet matches the current rule. If wmanIf2CmnClassifierRuleEnetProtocolType is ethertype(1) ,this object gives the 16-bit value of the EtherType that the packet must match in order to match the rule. If wmanIf2CmnClassifierRuleEnetProtocolType is dsap(2), the lower 8 bits of this object's value must match the DSAP byte of the packet in order to match the rule. If the Ethernet frame contains an 802.1P/Q Tag header (i.e. EtherType 0x8100), this object applies to the embedded EtherType field within the 802.1P/Q header. If the referenced parameter is not present in the classifier, the value of this object is reported as 0." REFERENCE "Subclause 11.13.19.3.4.10 in IEEE Std 802.16-2004" ::= { wmanIf2CmnClassifierRuleEntry 20 } wmanIf2CmnClassifierRuleUserPriLow OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-only STATUS current DESCRIPTION "This object applies only to Ethernet frames using the 802.1P/Q tag header (indicated with EtherType 0x8100). Such frames include a 16-bit Tag that contains a 3 bit Priority field and a 12 bit VLAN number. Tagged Ethernet packets must have a 3-bit Priority field within the range of wmanIf2CmnClassifierRulePriLow and wmanIf2CmnClassifierRulePriHigh in order to match this rule. If the referenced parameter is not present in the classifier, the value of this object is reported as 0." REFERENCE "Subclause 11.13.19.3.4.11 in IEEE Std 802.16-2004" ::= { wmanIf2CmnClassifierRuleEntry 21 } wmanIf2CmnClassifierRuleUserPriHigh OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-only STATUS current DESCRIPTION "This object applies only to Ethernet frames using the 802.1P/Q tag header (indicated with EtherType 0x8100). Such frames include a 16-bit Tag that contains a 3 bit Priority field and a 12 bit VLAN number. Tagged Ethernet packets must have a 3-bit Priority field within the range of wmanIf2CmnClassifierRulePriLow and wmanIf2CmnClassifierRulePriHigh in order to match this rule. If the referenced parameter is not present in the classifier, the value of this object is reported as 7." REFERENCE "Subclause 11.13.19.3.4.11 in IEEE Std 802.16-2004" ::= { wmanIf2CmnClassifierRuleEntry 22 } wmanIf2CmnClassifierRuleVlanId OBJECT-TYPE SYNTAX Integer32 (0..4095) MAX-ACCESS read-only STATUS current DESCRIPTION "This object applies only to Ethernet frames using the 802.1P/Q tag header. If this object's value is nonzero, tagged packets must have a VLAN Identifier that matches the value in order to match the rule. Only the least significant 12 bits of this object's value are valid. If the referenced parameter is not present in the classifier, the value of this object is reported as 0." REFERENCE "Subclause 11.13.19.3.4.12 in IEEE Std 802.16-2004" ::= { wmanIf2CmnClassifierRuleEntry 23 } wmanIf2CmnClassifierRuleState OBJECT-TYPE SYNTAX INTEGER {active(1), inactive(2)} MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This object indicates whether or not the classifier is enabled to classify packets to a Service Flow. If the referenced parameter is not present in the classifier, the value of this object is reported as active(1)." ::= { wmanIf2CmnClassifierRuleEntry 24 } wmanIf2CmnClassifierRulePkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This object counts the number of packets that have been classified using this entry." ::= { wmanIf2CmnClassifierRuleEntry 25 } wmanIf2CmnClassifierRuleIpv6FlowLabel OBJECT-TYPE SYNTAX WmanIf2Ipv6FlowLabel MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this field specifies the matching values for the IPv6 Flow label field." ::= { wmanIf2CmnClassifierRuleEntry 26 } wmanIf2CmnClassifierRuleBitMap OBJECT-TYPE SYNTAX WmanIf2ClassifierBitMap MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates which parameter encodings were actually present in the entry. A bit set to '1' indicates the corresponding classifier encoding is present, and '0' means otherwise" ::= { wmanIf2CmnClassifierRuleEntry 27 } wmanIf2CmnPhsRuleTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2CmnPhsRuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains PHS rule dictionary entries. Each entry contains the data of the header to be suppressed along with its identification - PHSI. The classifier uniquely maps packets to its associated PHS Rule. The receiving entity uses the CID and the PHSI to restore the PHSF. Once a PHSF has been assigned to a PHSI, it shall not be changed. To change the value of a PHSF on a service flow, a new PHS rule shall be defined, the old rule is removed from the service flow, and the new rule is added. When a classifier is deleted, any associated PHS rule shall also be deleted." REFERENCE "Subclause 5.2.3 in IEEE Std 802.16-2004" ::= { wmanIf2CmnPacketCs 2 } wmanIf2CmnPhsRuleEntry OBJECT-TYPE SYNTAX WmanIf2CmnPhsRuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each PHS rule created dynamically by the BS and SS on a given service flow. The PHS rule is defined by the pair (PHSS, PHSM) for each distinct header data. It is indexed by IfIndex, wmanIf2CmnCpsSfId, and wmanIf2CmnPhsIndex. The table is read-only for NMS. " INDEX { ifIndex, wmanIf2CmnCpsSfId, wmanIf2CmnPhsRulePhsIndex } ::= { wmanIf2CmnPhsRuleTable 1 } WmanIf2CmnPhsRuleEntry::= SEQUENCE { wmanIf2CmnPhsRulePhsIndex INTEGER, wmanIf2CmnPhsRulePhsField OCTET STRING, wmanIf2CmnPhsRulePhsMask OCTET STRING, wmanIf2CmnPhsRulePhsSize Integer32, wmanIf2CmnPhsRulePhsVerify WmanIf2PhsRuleVerify} wmanIf2CmnPhsRulePhsIndex OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The PHSI (PHS Index) has a value between 1 and 255, which uniquely references the suppressed byte string. The index is unique per service flow. The uplink and downlink PHSI values are independent of each other." REFERENCE "Subclause 11.13.19.3.7.1 in IEEE Std 802.16-2004" ::= { wmanIf2CmnPhsRuleEntry 1 } wmanIf2CmnPhsRulePhsField OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..65535)) MAX-ACCESS read-only STATUS current DESCRIPTION "The PHSF (PHS Field) is a string of bytes containing the header information to be suppressed by the sending CS and reconstructed by the receiving CS. The most significant byte of the string corresponds to the first byte of the CS-SDU." REFERENCE "Subclause 11.13.19.3.7.2 in IEEE Std 802.16-2004" ::= { wmanIf2CmnPhsRuleEntry 2 } wmanIf2CmnPhsRulePhsMask OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..65535)) MAX-ACCESS read-only STATUS current DESCRIPTION "The PHSM An 8-bit mask that indicates which bytes in the PHS Field (PHSF) to suppress and which bytes to not suppress. The PHSM allows fields, such as sequence numbers or checksums (which vary in value), to be excluded from suppression with the constant bytes around them suppressed. It is encodded as follows: bit 0: 0 = don't suppress the 1st byte of the suppression field 1 = suppress first byte of the suppression field bit 1: 0 = don't suppress the 2nd byte of the suppression field 1 = suppress second byte of the suppression field bit x: 0 = don't suppress the (x+1) byte of the suppression field 1 = suppress (x+1) byte of the suppression field where the length of the octet string is ceiling (wmanIf2CmnPhsRulePhsSize/8)." REFERENCE "Subclause 11.13.19.3.7.3 in IEEE Std 802.16-2004" ::= { wmanIf2CmnPhsRuleEntry 3 } wmanIf2CmnPhsRulePhsSize OBJECT-TYPE SYNTAX Integer32 (0..255) UNITS "byte" MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this field - PHSS is the total number of bytes in the header to be suppressed and then restored in a service flow that uses PHS." REFERENCE "Subclause 11.13.19.3.7.4 in IEEE Std 802.16-2004" DEFVAL {0} ::= { wmanIf2CmnPhsRuleEntry 4 } wmanIf2CmnPhsRulePhsVerify OBJECT-TYPE SYNTAX WmanIf2PhsRuleVerify MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this field indicates to the sending entity whether or not the packet header contents are to be verified prior to performing suppression." DEFVAL { phsVerifyEnable } ::= { wmanIf2CmnPhsRuleEntry 5 } -- -- wmanIf2CmnCps contain the Common Part Sublayer objects that are -- common to both Base Station and Subscriber Station -- wmanIf2CmnCps OBJECT IDENTIFIER ::= { wmanIf2CommonObjects 2 } wmanIf2CmnCpsServiceFlowTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2CmnCpsServiceFlowEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains Service Flow managed objects that are common in BS and SS." ::= { wmanIf2CmnCps 1 } wmanIf2CmnCpsServiceFlowEntry OBJECT-TYPE SYNTAX WmanIf2CmnCpsServiceFlowEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each created service flow for a given MacAddress, and is indexed by ifIndex, wmanIf2CmnCpsCpsSfMacAddress, and wmanIf2CmnCpsSfId. IfIndex is associated with the BS sector." INDEX { ifIndex, wmanIf2CmnCpsSfMacAddress, wmanIf2CmnCpsSfId } ::= { wmanIf2CmnCpsServiceFlowTable 1 } WmanIf2CmnCpsServiceFlowEntry::= SEQUENCE { wmanIf2CmnCpsSfMacAddress MacAddress, wmanIf2CmnCpsSfId Unsigned32, wmanIf2CmnCpsSfCid WmanIf2CidType, wmanIf2CmnCpsSfDirection INTEGER, wmanIf2CmnCpsSfState WmanIf2SfState, wmanIf2CmnCpsTrafficPriority INTEGER, wmanIf2CmnCpsMaxSustainedRate Unsigned32, wmanIf2CmnCpsMaxTrafficBurst Unsigned32, wmanIf2CmnCpsMinReservedRate Unsigned32, wmanIf2CmnCpsToleratedJitter Unsigned32, wmanIf2CmnCpsMaxLatency Unsigned32, wmanIf2CmnCpsFixedVsVariableSduInd INTEGER, wmanIf2CmnCpsSduSize Unsigned32, wmanIf2CmnCpsSfSchedulingType WmanIf2SfSchedulingType, wmanIf2CmnCpsArqEnable TruthValue, wmanIf2CmnCpsArqWindowSize INTEGER, wmanIf2CmnCpsArqBlockLifetime INTEGER, wmanIf2CmnCpsArqSyncLossTimeout INTEGER, wmanIf2CmnCpsArqDeliverInOrder TruthValue, wmanIf2CmnCpsArqRxPurgeTimeout INTEGER, wmanIf2CmnCpsArqBlockSize INTEGER, wmanIf2CmnCpsMinRsvdTolerableRate Unsigned32, wmanIf2CmnCpsReqTxPolicy BITS, wmanIf2CmnSfCsSpecification WmanIf2CsSpecification, wmanIf2CmnCpsTargetSaid INTEGER} wmanIf2CmnCpsSfMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "When this table is implemented on the basestation, this object contains the SS Mac address, the reported service flow was created for. On the SS, the value returned is the SS's own Mac address." ::= { wmanIf2CmnCpsServiceFlowEntry 1 } wmanIf2CmnCpsSfId OBJECT-TYPE SYNTAX Unsigned32 ( 1 .. 4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "A 32 bit quantity that uniquely identifies a service flow to both the subscriber station and base station (BS)." ::= { wmanIf2CmnCpsServiceFlowEntry 2 } wmanIf2CmnCpsSfCid OBJECT-TYPE SYNTAX WmanIf2CidType MAX-ACCESS read-only STATUS current DESCRIPTION "A 16 bit channel identifier to identify the connection being created by DSA." ::= { wmanIf2CmnCpsServiceFlowEntry 3 } wmanIf2CmnCpsSfDirection OBJECT-TYPE SYNTAX INTEGER {downstream(1), upstream(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "An attribute indicating the service flow is downstream or upstream." ::= { wmanIf2CmnCpsServiceFlowEntry 4 } wmanIf2CmnCpsSfState OBJECT-TYPE SYNTAX WmanIf2SfState MAX-ACCESS read-only STATUS current DESCRIPTION "wmanIf2CmnCpsSfState indicates the service flow state: Authorized (1), Admitted (2), and Active (3) service flow state." REFERENCE "Subclause 6.3.14.6, in IEEE Std 802.16-2004" ::= { wmanIf2CmnCpsServiceFlowEntry 5 } wmanIf2CmnCpsTrafficPriority OBJECT-TYPE SYNTAX INTEGER (0 .. 7) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this parameter specifies the priority assigned to a service flow. For uplink service flows, the BS should use this parameter when determining precedence in request service and grant generation, and the SS shall preferentially select contention Request opportunities for Priority Request CIDs based on this priority" REFERENCE "Subclause 11.13.5 in IEEE Std 802.16-2004" ::= { wmanIf2CmnCpsServiceFlowEntry 6 } wmanIf2CmnCpsMaxSustainedRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "b/s" MAX-ACCESS read-only STATUS current DESCRIPTION "This parameter defines the peak information rate of the service. The rate is expressed in bits per second and pertains to the SDUs at the input to the system." REFERENCE "Subclause 11.13.6 in IEEE Std 802.16-2004" ::= { wmanIf2CmnCpsServiceFlowEntry 7 } wmanIf2CmnCpsMaxTrafficBurst OBJECT-TYPE SYNTAX Unsigned32 UNITS "byte" MAX-ACCESS read-only STATUS current DESCRIPTION "This parameter defines the maximum burst size that must be accommodated for the service." REFERENCE "Subclause 11.13.7 in IEEE Std 802.16-2004" ::= { wmanIf2CmnCpsServiceFlowEntry 8 } wmanIf2CmnCpsMinReservedRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "byte" MAX-ACCESS read-only STATUS current DESCRIPTION "This parameter specifies the minimum rate reserved for this service flow." REFERENCE "Subclause 11.13.8 in IEEE Std 802.16-2004" ::= { wmanIf2CmnCpsServiceFlowEntry 9 } wmanIf2CmnCpsToleratedJitter OBJECT-TYPE SYNTAX Unsigned32 UNITS "millisecond" MAX-ACCESS read-only STATUS current DESCRIPTION "This parameter defines the Maximum delay variation (jitter) for the connection." REFERENCE "Subclause 11.13.13 in IEEE Std 802.16-2004" ::= { wmanIf2CmnCpsServiceFlowEntry 10 } wmanIf2CmnCpsMaxLatency OBJECT-TYPE SYNTAX Unsigned32 UNITS "millisecond" MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this parameter specifies the maximum latency between the reception of a packet by the BS or SS on its network interface and the forwarding of the packet to its RF Interface." REFERENCE "Subclause 11.13.14 in IEEE Std 802.16-2004" ::= { wmanIf2CmnCpsServiceFlowEntry 11 } wmanIf2CmnCpsFixedVsVariableSduInd OBJECT-TYPE SYNTAX INTEGER {variableLength(0), fixedLength(1)} MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this parameter specifies whether the SDUs on the service flow are variable-length (0) or fixed-length (1). The parameter is used only if packing is on for the service flow. The default value is 0, i.e.,variable-length SDUs." REFERENCE "Subclause 11.13.15 in IEEE Std 802.16-2004" DEFVAL { variableLength } ::= { wmanIf2CmnCpsServiceFlowEntry 12 } wmanIf2CmnCpsSduSize OBJECT-TYPE SYNTAX Unsigned32 UNITS "byte" MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this parameter specifies the length of the SDU for a fixed-length SDU service flow. This parameter is used only if packing is on and the service flow is indicated as carrying fixed-length SDUs. The default value is 49 bytes, i.e., VC-switched ATM cells with PHS. The parameter is relevant for both ATM and Packet Convergence Sublayers." REFERENCE "Subclause 11.13.16 in IEEE Std 802.16-2004" DEFVAL { 49 } ::= { wmanIf2CmnCpsServiceFlowEntry 13 } wmanIf2CmnCpsSfSchedulingType OBJECT-TYPE SYNTAX WmanIf2SfSchedulingType MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the upstream scheduling service used for upstream service flow. If the referenced parameter is not present in the corresponding 802.16 QOS Parameter Set of an upstream service flow, the default value of this object is bestEffort(2)." REFERENCE "Subclause 11.13.11 in IEEE Std 802.16-2004" DEFVAL { bestEffort } ::= { wmanIf2CmnCpsServiceFlowEntry 14 } wmanIf2CmnCpsArqEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "True(1) ARQ enabling is requested for the connection." ::= { wmanIf2CmnCpsServiceFlowEntry 15 } wmanIf2CmnCpsArqWindowSize OBJECT-TYPE SYNTAX INTEGER (1..1024) MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the maximum number of unacknowledged fragments at any time." ::= { wmanIf2CmnCpsServiceFlowEntry 16 } wmanIf2CmnCpsArqBlockLifetime OBJECT-TYPE SYNTAX INTEGER (0 .. 65535) UNITS "10 us" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum time interval an ARQ fragment will be managed by the transmitter ARQ machine, once initial transmission of the fragment has occured. If transmission or retransmission of the fragment is not acknowledged by the receiver before the time limit is reached, the fragment is discarded. A value of 0 means Infinite." ::= { wmanIf2CmnCpsServiceFlowEntry 17 } wmanIf2CmnCpsArqSyncLossTimeout OBJECT-TYPE SYNTAX INTEGER (0 .. 65535 ) UNITS "10 us" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum interval before declaring a loss of synchronization of the sender and receiver state machines. A value of 0 means Infinite." ::= { wmanIf2CmnCpsServiceFlowEntry 18 } wmanIf2CmnCpsArqDeliverInOrder OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether or not data is to be delivered by the receiving MAC to its client application in the order in which data was handed off to the originating MAC." ::= { wmanIf2CmnCpsServiceFlowEntry 19 } wmanIf2CmnCpsArqRxPurgeTimeout OBJECT-TYPE SYNTAX INTEGER (0 .. 65535) UNITS "10 us" MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the time interval the ARQ window is advanced after a fragment is received. A value of 0 means Infinite." ::= { wmanIf2CmnCpsServiceFlowEntry 20 } wmanIf2CmnCpsArqBlockSize OBJECT-TYPE SYNTAX INTEGER (1..2040) UNITS "byte" MAX-ACCESS read-only STATUS current DESCRIPTION "This value of this parameter specifies the size of an ARQ block. This parameter shall be established by negotiation during the connection creation dialog." REFERENCE "Subclause 11.13.18.8 in IEEE Std 802.16-2004" ::= { wmanIf2CmnCpsServiceFlowEntry 21 } wmanIf2CmnCpsMinRsvdTolerableRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "b/s" MAX-ACCESS read-only STATUS current DESCRIPTION "Minimum Tolerable Traffic Rate = R (bits/sec) with time base T(sec) means the following. Let S denote additional demand accumulated at the MAC SAP of the transmitter during an arbitrary time interval of the length T. Then the amount of data forwarded at the receiver to CS (in bits) during this interval should be not less than min {S, R * T}." REFERENCE "Subclause 11.13.9 in IEEE Std 802.16-2004" ::= { wmanIf2CmnCpsServiceFlowEntry 22 } wmanIf2CmnCpsReqTxPolicy OBJECT-TYPE SYNTAX BITS {noBroadcastBwReq(0), reserved1(1), noPiggybackReq(2), noFragmentData(3), noPHS(4), noSduPacking(5), noCrc(6), reserved2(7)} MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this parameter provides the capability to specify certain attributes for the associated service flow. An attribute is enabled by setting the corresponding bit position to 1." REFERENCE "Subclause 11.13.12 in IEEE Std 802.16-2004" ::= { wmanIf2CmnCpsServiceFlowEntry 23 } wmanIf2CmnSfCsSpecification OBJECT-TYPE SYNTAX WmanIf2CsSpecification MAX-ACCESS read-only STATUS current DESCRIPTION "This parameter specifies the convergence sublayer encapsulation mode." REFERENCE "Subclause 11.13.19.1 in IEEE Std 802.16-2004" ::= { wmanIf2CmnCpsServiceFlowEntry 24 } wmanIf2CmnCpsTargetSaid OBJECT-TYPE SYNTAX INTEGER (0 .. 65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The target SAID parameter indicates the SAID onto which the service flow being set up shall be mapped." REFERENCE "Subclause 11.13.17 in IEEE Std 802.16-2004" ::= { wmanIf2CmnCpsServiceFlowEntry 25 } -- -- wmanIf2CmnBsSsConfigurationTable contains global parameters -- common in BS and SS -- wmanIf2CmnBsSsConfigurationTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2CmnBsSsConfigurationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each BS sector that contains the system parameters common in both SS and BS. All SSs shall have the same parameters as the BS to which the SSs are associated." REFERENCE "Subclause 10.1 in IEEE Std 802.16-2004" ::= { wmanIf2CmnCps 2 } wmanIf2CmnBsSsConfigurationEntry OBJECT-TYPE SYNTAX WmanIf2CmnBsSsConfigurationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is indexed by ifIndex, indicating BS sector." INDEX { ifIndex } ::= { wmanIf2CmnBsSsConfigurationTable 1 } WmanIf2CmnBsSsConfigurationEntry ::= SEQUENCE { wmanIf2CmnInvitedRangRetries INTEGER, wmanIf2CmnDSxReqRetries Unsigned32, wmanIf2CmnDSxRespRetries Unsigned32, wmanIf2CmnT7Timeout INTEGER, wmanIf2CmnT8Timeout INTEGER, wmanIf2CmnT10Timeout INTEGER, wmanIf2CmnT22Timeout INTEGER} wmanIf2CmnInvitedRangRetries OBJECT-TYPE SYNTAX INTEGER (16..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Number of retries on inviting Ranging Requests." ::= { wmanIf2CmnBsSsConfigurationEntry 1 } wmanIf2CmnDSxReqRetries OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Number of Timeout Retries on DSA/DSC/DSD Requests." DEFVAL { 3 } ::= { wmanIf2CmnBsSsConfigurationEntry 2 } wmanIf2CmnDSxRespRetries OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Number of Timeout Retries on DSA/DSC/DSD Responses." DEFVAL { 3 } ::= { wmanIf2CmnBsSsConfigurationEntry 3 } wmanIf2CmnT7Timeout OBJECT-TYPE SYNTAX INTEGER (0 .. 1000) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Wait for DSA/DSC/DSD Response Timeout in ms." ::= { wmanIf2CmnBsSsConfigurationEntry 4 } wmanIf2CmnT8Timeout OBJECT-TYPE SYNTAX INTEGER (0 .. 300) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Wait for DSA/DSC/DSD Acknowledge Timeout in ms." ::= { wmanIf2CmnBsSsConfigurationEntry 5 } wmanIf2CmnT10Timeout OBJECT-TYPE SYNTAX INTEGER (0 .. 3000) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Wait for Transaction End timeout in ms." ::= { wmanIf2CmnBsSsConfigurationEntry 6 } wmanIf2CmnT22Timeout OBJECT-TYPE SYNTAX INTEGER (0 .. 500) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Wait for ARQ Reset in ms." ::= { wmanIf2CmnBsSsConfigurationEntry 7 } -- Common PKM group -- wmanIf2CmnPkmObjects contain the Privacy Sublayer objects that are -- common to both Base Station and Subscriber Station -- wmanIf2CmnPkmObjects OBJECT IDENTIFIER ::= { wmanIf2CommonObjects 3 } -- -- Table wmanIf2CmnCryptoSuiteTable -- wmanIf2CmnCryptoSuiteTable OBJECT-TYPE SYNTAX SEQUENCE OF WmanIf2CmnCryptoSuiteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the PKM cryptographic suite capabilites for each SS or BS wireless interface." ::= { wmanIf2CmnPkmObjects 1 } wmanIf2CmnCryptoSuiteEntry OBJECT-TYPE SYNTAX WmanIf2CmnCryptoSuiteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains the cryptographic suite pair that SS or BS supports." INDEX { ifIndex, wmanIf2CmnCryptoSuiteIndex } ::= { wmanIf2CmnCryptoSuiteTable 1 } WmanIf2CmnCryptoSuiteEntry ::= SEQUENCE { wmanIf2CmnCryptoSuiteIndex Integer32, wmanIf2CmnCryptoSuiteDataEncryptAlg WmanIf2DataEncryptAlgId, wmanIf2CmnCryptoSuiteDataAuthentAlg WmanIf2DataAuthAlgId, wmanIf2CmnCryptoSuiteTekEncryptAlg WmanIf2TekEncryptAlgId} wmanIf2CmnCryptoSuiteIndex OBJECT-TYPE SYNTAX Integer32 (1 .. 1000) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index for a cryptographic suite row." ::= { wmanIf2CmnCryptoSuiteEntry 1 } wmanIf2CmnCryptoSuiteDataEncryptAlg OBJECT-TYPE SYNTAX WmanIf2DataEncryptAlgId MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the data encryption algorithm for this cryptographic suite capability." REFERENCE "Table 375, IEEE Std 802.16-2004" ::= { wmanIf2CmnCryptoSuiteEntry 2 } wmanIf2CmnCryptoSuiteDataAuthentAlg OBJECT-TYPE SYNTAX WmanIf2DataAuthAlgId MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the data authentication algorithm for this cryptographic suite capability." REFERENCE "Table 376, IEEE Std 802.16-2004" ::= { wmanIf2CmnCryptoSuiteEntry 3 } wmanIf2CmnCryptoSuiteTekEncryptAlg OBJECT-TYPE SYNTAX WmanIf2TekEncryptAlgId MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the TEK key encryption algorithm for this cryptographic suite capability." REFERENCE "Table 377, IEEE Std 802.16-2004" ::= { wmanIf2CmnCryptoSuiteEntry 4 } -- -- Conformance Information -- wmanIf2MibConformance OBJECT IDENTIFIER ::= {wmanIf2Mib 2} wmanIf2MibGroups OBJECT IDENTIFIER ::= {wmanIf2MibConformance 1} wmanIf2MibCompliances OBJECT IDENTIFIER ::= {wmanIf2MibConformance 2} -- compliance statements wmanIf2MibCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for devices that implement Wireless MAN interfaces as defined in IEEE Std 802.16-2004." MODULE -- wmanIf2Mib MANDATORY-GROUPS -- unconditionally mandatory groups { wmanIf2MibCommonGroup } GROUP wmanIf2MibQoSGroup -- unconditionally mandatory group DESCRIPTION "This group is mandatory for Base Station and subscriber station." GROUP wmanIf2MibBsGroup -- conditionally mandatory group DESCRIPTION "This group is mandatory for Base Station." GROUP wmanIf2MibBsAasGroup -- optional group DESCRIPTION "This group is mandatory for Base Station." GROUP wmanIf2MibSsGroup -- conditionally mandatory group DESCRIPTION "This group is mandatory for Subscriber Station." GROUP wmanIf2MibBsOfdmGroup -- conditionally mandatory group DESCRIPTION "This group is mandatory for Base Station implementaing the OFDM PHY." GROUP wmanIf2MibSsOfdmGroup -- conditionally mandatory group DESCRIPTION "This group is mandatory for Subscriber Station implementing the OFDM PHY." GROUP wmanIf2MibBsOfdmaGroup -- conditionally mandatory group DESCRIPTION "This group is mandatory for Base Station implementaing the OFDMA PHY." GROUP wmanIf2MibSsOfdmaGroup -- conditionally mandatory group DESCRIPTION "This group is mandatory for Subscriber Station implementing the OFDMA PHY." GROUP wmanIf2MibBsNotificationGroup -- unconditionally -- mandatory groups DESCRIPTION "This group is mandatory for Base Station." GROUP wmanIf2MibSsNotificationGroup -- optional group DESCRIPTION "This group is optional for Subscriber Station." GROUP wmanIf2MibCmnPhsGroup -- optional group DESCRIPTION "This group is optional for Base Station and Subscriber Station." GROUP wmanIf2MibBsPhsGroup -- optional group DESCRIPTION "This group is optional for Base Station." ::= { wmanIf2MibCompliances 1 } wmanIf2MibCommonGroup OBJECT-GROUP OBJECTS {-- Classification wmanIf2CmnClassifierRulePriority, wmanIf2CmnClassifierRuleIpTosLow, wmanIf2CmnClassifierRuleIpTosHigh, wmanIf2CmnClassifierRuleIpTosMask, wmanIf2CmnClassifierRuleIpProtocol, wmanIf2CmnClassifierRuleIpSourceAddr, wmanIf2CmnClassifierRuleIpSourceMask, wmanIf2CmnClassifierRuleIpDestAddr, wmanIf2CmnClassifierRuleIpDestMask, wmanIf2CmnClassifierRuleSourcePortStart, wmanIf2CmnClassifierRuleSourcePortEnd, wmanIf2CmnClassifierRuleDestPortStart, wmanIf2CmnClassifierRuleDestPortEnd, wmanIf2CmnClassifierRuleDestMacAddr, wmanIf2CmnClassifierRuleDestMacMask, wmanIf2CmnClassifierRuleSourceMacAddr, wmanIf2CmnClassifierRuleSourceMacMask, wmanIf2CmnClassifierRuleEnetProtocolType, wmanIf2CmnClassifierRuleEnetProtocol, wmanIf2CmnClassifierRuleUserPriLow, wmanIf2CmnClassifierRuleUserPriHigh, wmanIf2CmnClassifierRuleVlanId, wmanIf2CmnClassifierRuleState, wmanIf2CmnClassifierRulePkts, wmanIf2CmnClassifierRuleIpv6FlowLabel, wmanIf2CmnClassifierRuleBitMap, -- Configuration parameters wmanIf2CmnCpsTargetSaid, wmanIf2CmnInvitedRangRetries, wmanIf2CmnDSxReqRetries, wmanIf2CmnDSxRespRetries, wmanIf2CmnT7Timeout, wmanIf2CmnT8Timeout, wmanIf2CmnT10Timeout, wmanIf2CmnT22Timeout, wmanIf2CmnCryptoSuiteDataEncryptAlg, wmanIf2CmnCryptoSuiteDataAuthentAlg, wmanIf2CmnCryptoSuiteTekEncryptAlg} STATUS current DESCRIPTION "This group contains objects for both BS and SS, and are independent of PHY." ::= { wmanIf2MibGroups 1 } wmanIf2MibQoSGroup OBJECT-GROUP OBJECTS {wmanIf2CmnCpsSfId, wmanIf2CmnCpsSfCid, wmanIf2CmnCpsSfDirection, wmanIf2CmnCpsSfState, wmanIf2CmnCpsTrafficPriority, wmanIf2CmnCpsMaxSustainedRate, wmanIf2CmnCpsMaxTrafficBurst, wmanIf2CmnCpsMinReservedRate, wmanIf2CmnCpsToleratedJitter, wmanIf2CmnCpsMaxLatency, wmanIf2CmnCpsFixedVsVariableSduInd, wmanIf2CmnCpsSduSize, wmanIf2CmnCpsSfSchedulingType, wmanIf2CmnCpsArqEnable, wmanIf2CmnCpsArqWindowSize, wmanIf2CmnCpsArqBlockLifetime, wmanIf2CmnCpsArqSyncLossTimeout, wmanIf2CmnCpsArqDeliverInOrder, wmanIf2CmnCpsArqRxPurgeTimeout, wmanIf2CmnCpsArqBlockSize, wmanIf2CmnCpsMinRsvdTolerableRate, wmanIf2CmnCpsReqTxPolicy, wmanIf2CmnSfCsSpecification} STATUS current DESCRIPTION "This group contains QoS objects for both BS and SS." ::= { wmanIf2MibGroups 2 } wmanIf2MibBsGroup OBJECT-GROUP OBJECTS {-- Service classes wmanIf2BsSfDirection, wmanIf2BsServiceClassIndex, wmanIf2BsSfState, wmanIf2BsSfProvisionedTime, wmanIf2BsProvisionedSfRowStatus, wmanIf2BsSsProvisionedForSfRowStatus, wmanIf2BsSfCsSpecification, wmanIf2BsQosServiceClassName, wmanIf2BsQoSTrafficPriority, wmanIf2BsQoSMaxSustainedRate, wmanIf2BsQoSMaxTrafficBurst, wmanIf2BsQoSMinReservedRate, wmanIf2BsQoSToleratedJitter, wmanIf2BsQoSMaxLatency, wmanIf2BsQoSFixedVsVariableSduInd, wmanIf2BsQoSSduSize, wmanIf2BsQosScSchedulingType, wmanIf2BsQosScArqEnable, wmanIf2BsQosScArqWindowSize, wmanIf2BsQosScArqBlockLifetime, wmanIf2BsQosScArqSyncLossTimeout, wmanIf2BsQosScArqDeliverInOrder, wmanIf2BsQosScArqRxPurgeTimeout, wmanIf2BsQosScArqBlockSize, wmanIf2BsQosSCMinRsvdTolerableRate, wmanIf2BsQoSReqTxPolicy, wmanIf2BsQoSServiceClassRowStatus, -- Classification wmanIf2BsClassifierRulePriority, wmanIf2BsClassifierRuleIpTosLow, wmanIf2BsClassifierRuleIpTosHigh, wmanIf2BsClassifierRuleIpTosMask, wmanIf2BsClassifierRuleIpProtocol, wmanIf2BsClassifierRuleIpSourceAddr, wmanIf2BsClassifierRuleIpSourceMask, wmanIf2BsClassifierRuleIpDestAddr, wmanIf2BsClassifierRuleIpDestMask, wmanIf2BsClassifierRuleSourcePortStart, wmanIf2BsClassifierRuleSourcePortEnd, wmanIf2BsClassifierRuleDestPortStart, wmanIf2BsClassifierRuleDestPortEnd, wmanIf2BsClassifierRuleDestMacAddr, wmanIf2BsClassifierRuleDestMacMask, wmanIf2BsClassifierRuleSourceMacAddr, wmanIf2BsClassifierRuleSourceMacMask, wmanIf2BsClassifierRuleEnetProtocolType, wmanIf2BsClassifierRuleEnetProtocol, wmanIf2BsClassifierRuleUserPriLow, wmanIf2BsClassifierRuleUserPriHigh, wmanIf2BsClassifierRuleVlanId, wmanIf2BsClassifierRuleState, wmanIf2BsClassifierRulePhsSize, wmanIf2BsClassifierRulePhsMask, wmanIf2BsClassifierRulePhsVerify, wmanIf2BsClassifierRuleIpv6FlowLabel, wmanIf2BsClassifierRuleBitMap, wmanIf2BsClassifierRuleRowStatus, -- Packet counters wmanIf2BsSsMacSduCount, wmanIf2BsSsOctetCount, wmanIf2BsSsResetCounter, wmanIf2BsSsResetCounterTime, -- Capability negotiation wmanIf2BsSsBasicCid, wmanIf2BsSsPrimaryCid, wmanIf2BsSsSecondaryCid, wmanIf2BsSsManagementSupport, wmanIf2BsSsIpManagementMode, wmanIf2Bs2ndMgmtDlQoSProfileIndex, wmanIf2Bs2ndMgmtUlQoSProfileIndex, wmanIf2BsAutoSfidEnabled, wmanIf2BsAutoSfidRangeMin, wmanIf2BsAutoSfidRangeMax, wmanIf2BsResetSector, wmanIf2BsSs2ndMgmtArqEnable, wmanIf2BsSs2ndMgmtArqWindowSize, wmanIf2BsSs2ndMgmtArqDnLinkTxDelay, wmanIf2BsSs2ndMgmtArqUpLinkTxDelay, wmanIf2BsSs2ndMgmtArqDnLinkRxDelay, wmanIf2BsSs2ndMgmtArqUpLinkRxDelay, wmanIf2BsSs2ndMgmtArqBlockLifetime, wmanIf2BsSs2ndMgmtArqSyncLossTimeout, wmanIf2BsSs2ndMgmtArqDeliverInOrder, wmanIf2BsSs2ndMgmtArqRxPurgeTimeout, wmanIf2BsSs2ndMgmtArqBlockSize, wmanIf2BsSsVendorIdEncoding, wmanIf2BsSsAasBroadcastPermission, wmanIf2BsSsMaxTxPowerBpsk, wmanIf2BsSsMaxTxPowerQpsk, wmanIf2BsSsMaxTxPower16Qam, wmanIf2BsSsMaxTxPower64Qam, -- Configuration parameters wmanIf2BsSsMacVersion, wmanIf2BsDcdInterval, wmanIf2BsUcdInterval, wmanIf2BsUcdTransition, wmanIf2BsDcdTransition, wmanIf2BsInitialRangingInterval, wmanIf2BsSsULMapProcTime, wmanIf2BsSsRangRespProcTime, wmanIf2BsT5Timeout, wmanIf2BsT9Timeout, wmanIf2BsT13Timeout, wmanIf2BsT15Timeout, wmanIf2BsT17Timeout, wmanIf2BsT27IdleTimer, wmanIf2BsT27ActiveTimer, -- Performance monitoring wmanIf2BsHistogramIndex, wmanIf2BsChannelNumber, wmanIf2BsStartFrame, wmanIf2BsDuration, wmanIf2BsBasicReport, wmanIf2BsMeanCinrReport, wmanIf2BsMeanRssiReport, wmanIf2BsStdDeviationCinrReport, wmanIf2BsStdDeviationRssiReport, -- Capability negotiation wmanIf2BsSsReqCapUplinkCidSupport, wmanIf2BsSsReqCapArqSupport, wmanIf2BsSsReqCapDsxFlowControl, wmanIf2BsSsReqCapMacCrcSupport, wmanIf2BsSsReqCapMcaFlowControl, wmanIf2BsSsReqCapMcpGroupCidSupport, wmanIf2BsSsReqCapPkmFlowControl, wmanIf2BsSsReqCapAuthPolicyControl, wmanIf2BsSsReqCapMaxNumOfSupportedSA, wmanIf2BsSsReqCapIpVersion, wmanIf2BsSsReqCapMacCsSupportBitMap, wmanIf2BsSsReqCapMaxNumOfClassifier, wmanIf2BsSsReqCapPhsSupport, wmanIf2BsSsReqCapBandwidthAllocSupport, wmanIf2BsSsReqCapPduConstruction, wmanIf2BsSsReqCapTtgTransitionGap, wmanIf2BsSsReqCapRtgTransitionGap, wmanIf2BsSsRspCapUplinkCidSupport, wmanIf2BsSsRspCapArqSupport, wmanIf2BsSsRspCapDsxFlowControl, wmanIf2BsSsRspCapMacCrcSupport, wmanIf2BsSsRspCapMcaFlowControl, wmanIf2BsSsRspCapMcpGroupCidSupport, wmanIf2BsSsRspCapPkmFlowControl, wmanIf2BsSsRspCapAuthPolicyControl, wmanIf2BsSsRspCapMaxNumOfSupportedSA, wmanIf2BsSsRspCapIpVersion, wmanIf2BsSsRspCapMacCsSupportBitMap, wmanIf2BsSsRspCapMaxNumOfClassifier, wmanIf2BsSsRspCapPhsSupport, wmanIf2BsSsRspCapBandwidthAllocSupport, wmanIf2BsSsRspCapPduConstruction, wmanIf2BsSsRspCapTtgTransitionGap, wmanIf2BsSsRspCapRtgTransitionGap, wmanIf2BsCapUplinkCidSupport, wmanIf2BsCapArqSupport, wmanIf2BsCapDsxFlowControl, wmanIf2BsCapMacCrcSupport, wmanIf2BsCapMcaFlowControl, wmanIf2BsCapMcpGroupCidSupport, wmanIf2BsCapPkmFlowControl, wmanIf2BsCapAuthPolicyControl, wmanIf2BsCapMaxNumOfSupportedSA, wmanIf2BsCapIpVersion, wmanIf2BsCapMacCsSupportBitMap, wmanIf2BsCapMaxNumOfClassifier, wmanIf2BsCapPhsSupport, wmanIf2BsCapBandwidthAllocSupport, wmanIf2BsCapPduConstruction, wmanIf2BsCapTtgTransitionGap, wmanIf2BsCapRtgTransitionGap, wmanIf2BsCapCfgUplinkCidSupport, wmanIf2BsCapCfgArqSupport, wmanIf2BsCapCfgDsxFlowControl, wmanIf2BsCapCfgMacCrcSupport, wmanIf2BsCapCfgMcaFlowControl, wmanIf2BsCapCfgMcpGroupCidSupport, wmanIf2BsCapCfgPkmFlowControl, wmanIf2BsCapCfgAuthPolicyControl, wmanIf2BsCapCfgMaxNumOfSupportedSA, wmanIf2BsCapCfgIpVersion, wmanIf2BsCapCfgMacCsSupportBitMap, wmanIf2BsCapCfgMaxNumOfClassifier, wmanIf2BsCapCfgPhsSupport, wmanIf2BsCapCfgBandwidthAllocSupport, wmanIf2BsCapCfgPduConstruction, wmanIf2BsCapCfgTtgTransitionGap, wmanIf2BsCapCfgRtgTransitionGap, wmanIf2BsSsActionsResetSs, wmanIf2BsSsActionsAbortSs, wmanIf2BsSsActionsOverrideDnFreq, wmanIf2BsSsActionsOverrideChannelId, wmanIf2BsSsActionsDeReRegSs, wmanIf2BsSsActionsDeReRegSsCode, wmanIf2BsSsActionsRowStatus, -- Privacy sublayer wmanIf2BsPkmDefaultAuthLifetime, wmanIf2BsPkmDefaultTekLifetime, wmanIf2BsPkmDefaultSelfSigManufCertTrust, wmanIf2BsPkmCheckCertValidityPeriods, wmanIf2BsPkmAuthentInfos, wmanIf2BsPkmAuthRequests, wmanIf2BsPkmAuthReplies, wmanIf2BsPkmAuthRejects, wmanIf2BsPkmAuthInvalids, wmanIf2BsSsPkmAuthKeySequenceNumber, wmanIf2BsSsPkmAuthExpiresOld, wmanIf2BsSsPkmAuthExpiresNew, wmanIf2BsSsPkmAuthLifetime, wmanIf2BsSsPkmAuthReset, wmanIf2BsSsPkmAuthInfos, wmanIf2BsSsPkmAuthRequests, wmanIf2BsSsPkmAuthReplies, wmanIf2BsSsPkmAuthRejects, wmanIf2BsSsPkmAuthInvalids, wmanIf2BsSsPkmAuthRejectErrorCode, wmanIf2BsSsPkmAuthRejectErrorString, wmanIf2BsSsPkmAuthInvalidErrorCode, wmanIf2BsSsPkmAuthInvalidErrorString, wmanIf2BsSsPkmAuthPrimarySAId, wmanIf2BsSsPkmAuthValidStatus, wmanIf2BsPkmTekSAType, wmanIf2BsPkmTekDataEncryptAlg, wmanIf2BsPkmTekDataAuthentAlg, wmanIf2BsPkmTekEncryptAlg, wmanIf2BsPkmTekLifetime, wmanIf2BsPkmTekKeySequenceNumber, wmanIf2BsPkmTekExpiresOld, wmanIf2BsPkmTekExpiresNew, wmanIf2BsPkmTekReset, wmanIf2BsPkmKeyRequests, wmanIf2BsPkmKeyReplies, wmanIf2BsPkmKeyRejects, wmanIf2BsPkmTekInvalids, wmanIf2BsPkmKeyRejectErrorCode, wmanIf2BsPkmKeyRejectErrorString, wmanIf2BsPkmTekInvalidErrorCode, wmanIf2BsPkmTekInvalidErrorString, -- Notification wmanIf2BsTrapControlRegister, wmanIf2BsStatusTrapControlRegister, wmanIf2BsRssiLowThreshold, wmanIf2BsRssiHighThreshold, wmanIf2BsSsNotificationMacAddr, wmanIf2BsSsStatusValue, wmanIf2BsSsStatusInfo, wmanIf2BsDynamicServiceType, wmanIf2BsDynamicServiceFailReason, wmanIf2BsSsRssiStatus, wmanIf2BsSsRssiStatusInfo, wmanIf2BsSsRegisterStatus} STATUS current DESCRIPTION "This group contains objects for BS, and are independent of PHY." ::= { wmanIf2MibGroups 3 } wmanIf2MibBsAasGroup OBJECT-GROUP OBJECTS {-- AAS Configuration parameters wmanIf2BsAasChanFbckReqFreq, wmanIf2BsAasBeamSelectFreq, wmanIf2BsAasChanFbckReqResolution, wmanIf2BsAasBeamReqResolution, wmanIf2BsAasNumOptDiversityZones} STATUS current DESCRIPTION "This group contains objects for AAS in BS." ::= { wmanIf2MibGroups 4 } wmanIf2MibSsGroup OBJECT-GROUP OBJECTS {-- Configuration parameters wmanIf2SsLostDLMapInterval, wmanIf2SsLostULMapInterval, wmanIf2SsContentionRangRetries, wmanIf2SsRequestRetries, wmanIf2SsRegRequestRetries, wmanIf2SsTftpBackoffStart, wmanIf2SsTftpBackoffEnd, wmanIf2SsTftpRequestRetries, wmanIf2SsTftpDownloadRetries, wmanIf2SsTftpWait, wmanIf2SsToDRetries, wmanIf2SsToDRetryPeriod, wmanIf2SsT1Timeout, wmanIf2SsT2Timeout, wmanIf2SsT3Timeout, wmanIf2SsT4Timeout, wmanIf2SsT6Timeout, wmanIf2SsT12Timeout, wmanIf2SsT14Timeout, wmanIf2SsT16Timeout, wmanIf2SsT18Timeout, wmanIf2SsT19Timeout, wmanIf2SsT20Timeout, wmanIf2SsT21Timeout, wmanIf2SsSBCRequestRetries, wmanIf2SsTftpCpltRetries, wmanIf2SsT26Timeout, wmanIf2SsDLManagProcTime, -- Performance monitoring wmanIf2SsChannelNumber, wmanIf2SsStartFrame , wmanIf2SsDuration, wmanIf2SsBasicReport, wmanIf2SsMeanCinrReport, wmanIf2SsStdDeviationCinrReport, wmanIf2SsMeanRssiReport, wmanIf2SsStdDeviationRssiReport, -- Privacy sublayer wmanIf2SsPkmAuthState, wmanIf2SsPkmAuthKeySequenceNumber, wmanIf2SsPkmAuthExpiresOld, wmanIf2SsPkmAuthExpiresNew , wmanIf2SsPkmAuthReset, wmanIf2SsPkmAuthentInfos, wmanIf2SsPkmAuthRequests, wmanIf2SsPkmAuthReplies, wmanIf2SsPkmAuthRejects, wmanIf2SsPkmAuthInvalids, wmanIf2SsPkmAuthRejectErrorCode, wmanIf2SsPkmAuthRejectErrorString, wmanIf2SsPkmAuthInvalidErrorCode, wmanIf2SsPkmAuthInvalidErrorString , wmanIf2SsPkmAuthGraceTime, wmanIf2SsPkmTekGraceTime, wmanIf2SsPkmAuthWaitTimeout, wmanIf2SsPkmReauthWaitTimeout, wmanIf2SsPkmOpWaitTimeout, wmanIf2SsPkmRekeyWaitTimeout, wmanIf2SsPkmAuthRejectWaitTimeout, wmanIf2SsPkmTekSAType, wmanIf2SsPkmTekDataEncryptAlg, wmanIf2SsPkmTekDataAuthentAlg, wmanIf2SsPkmTekEncryptAlg, wmanIf2SsPkmTekState, wmanIf2SsPkmTekKeySequenceNumber, wmanIf2SsPkmTekExpiresOld, wmanIf2SsPkmTekExpiresNew, wmanIf2SsPkmTekKeyRequests, wmanIf2SsPkmTekKeyReplies, wmanIf2SsPkmTekKeyRejects, wmanIf2SsPkmTekInvalids, wmanIf2SsPkmTekAuthPends, wmanIf2SsPkmTekKeyRejectErrorCode, wmanIf2SsPkmTekKeyRejectErrorString, wmanIf2SsPkmTekInvalidErrorCode, wmanIf2SsPkmTekInvalidErrorString, wmanIf2SsDeviceCert, wmanIf2SsDeviceManufCert, -- Notofocation wmanIf2SsTrapControlRegister, wmanIf2SsRssiLowThreshold, wmanIf2SsRssiHighThreshold, wmanIf2SsMacAddress, wmanIf2SsUnknownTlv, wmanIf2SsDynamicServiceType, wmanIf2SsDynamicServiceFailReason, wmanIf2SsRssiStatus, wmanIf2SsRssiStatusInfo} STATUS current DESCRIPTION "This group contains objects for SS, and are independent of PHY." ::= { wmanIf2MibGroups 5 } wmanIf2MibBsOfdmGroup OBJECT-GROUP OBJECTS {wmanIf2BsOfdmCtBasedResvTimeout, wmanIf2BsOfdmBwReqOppSize, wmanIf2BsOfdmRangReqOppSize, wmanIf2BsOfdmUplinkCenterFreq, wmanIf2BsOfdmNumSubChReqRegionFull, wmanIf2BsOfdmNumSymbolsReqRegionFull, wmanIf2BsOfdmSubChFocusCtCode, wmanIf2BsOfdmUpLinkChannelId, wmanIf2BsOfdmBsEIRP, wmanIf2BsOfdmChannelNumber, wmanIf2BsOfdmTTG, wmanIf2BsOfdmRTG, wmanIf2BsOfdmInitRngMaxRSS, wmanIf2BsOfdmDownlinkCenterFreq, wmanIf2BsOfdmBsId, wmanIf2BsOfdmMacVersion, wmanIf2BsOfdmFrameDurationCode, wmanIf2BsOfdmDownLinkChannelId, wmanIf2BsOfdmUcdFecCodeType, wmanIf2BsOfdmFocusCtPowerBoost, wmanIf2BsOfdmUcdTcsEnable, wmanIf2BsOfdmUcdBurstProfileRowStatus, wmanIf2BsOfdmDownlinkFrequency, wmanIf2BsOfdmDcdFecCodeType, wmanIf2BsOfdmDiucMandatoryExitThresh, wmanIf2BsOfdmDiucMinEntryThresh, wmanIf2BsOfdmTcsEnable, wmanIf2BsOfdmDcdBurstProfileRowStatus, wmanIf2BsOfdmMinReqRegionFullTxOpp, wmanIf2BsOfdmMinFocusedCtTxOpp, wmanIf2BsOfdmMaxRoundTripDelay, wmanIf2BsOfdmRangeAbortTimingThold, wmanIf2BsOfdmRangeAbortPowerThold , wmanIf2BsOfdmRangeAbortFreqThold, wmanIf2BsOfdmDnlkRateId, wmanIf2BsOfdmRatioG, wmanIf2BsSsOfdmReqCapFftSizes, wmanIf2BsSsOfdmReqCapSsDemodulator, wmanIf2BsSsOfdmReqCapSsModulator, wmanIf2BsSsOfdmReqCapFocusedCtSupport, wmanIf2BsSsOfdmReqCapTcSublayerSupport, wmanIf2BsSsOfdmRspCapFftSizes, wmanIf2BsSsOfdmRspCapSsDemodulator, wmanIf2BsSsOfdmRspCapSsModulator, wmanIf2BsSsOfdmRspCapFocusedCtSupport, wmanIf2BsSsOfdmRspCapTcSublayerSupport, wmanIf2BsOfdmCapFftSizes, wmanIf2BsOfdmCapSsDemodulator, wmanIf2BsOfdmCapSsModulator, wmanIf2BsOfdmCapFocusedCtSupport, wmanIf2BsOfdmCapTcSublayerSupport, wmanIf2BsOfdmCapCfgFftSizes, wmanIf2BsOfdmCapCfgSsDemodulator, wmanIf2BsOfdmCapCfgSsModulator, wmanIf2BsOfdmCapCfgFocusedCtSupport, wmanIf2BsOfdmCapCfgTcSublayerSupport} STATUS current DESCRIPTION "This group contains objects for BS and OFDM PHY." ::= { wmanIf2MibGroups 6 } wmanIf2MibSsOfdmGroup OBJECT-GROUP OBJECTS {wmanIf2SsOfdmCtBasedResvTimeout, wmanIf2SsOfdmBwReqOppSize, wmanIf2SsOfdmRangReqOppSize, wmanIf2SsOfdmUplinkCenterFreq, wmanIf2SsOfdmNumSubChReqRegionFull, wmanIf2SsOfdmNumSymbolsReqRegionFull, wmanIf2SsOfdmSubChFocusCtCode, wmanIf2SsOfdmUpLinkChannelId, wmanIf2SsOfdmBsEIRP, wmanIf2SsOfdmChannelNumber, wmanIf2SsOfdmTTG, wmanIf2SsOfdmRTG, wmanIf2SsOfdmInitRngMaxRSS, wmanIf2SsOfdmDownlinkCenterFreq, wmanIf2SsOfdmBsId, wmanIf2SsOfdmMacVersion, wmanIf2SsOfdmFrameDurationCode, wmanIf2SsOfdmDownLinkChannelId, wmanIf2SsOfdmUcdFecCodeType, wmanIf2SsOfdmFocusCtPowerBoost, wmanIf2SsOfdmUcdTcsEnable, wmanIf2SsOfdmDownlinkFrequency, wmanIf2SsOfdmDcdFecCodeType, wmanIf2SsOfdmDiucMandatoryExitThresh, wmanIf2SsOfdmDiucMinEntryThresh, wmanIf2SsOfdmTcsEnable} STATUS current DESCRIPTION "This group contains objects for SS and OFDM PHY." ::= { wmanIf2MibGroups 7 } wmanIf2MibBsOfdmaGroup OBJECT-GROUP OBJECTS {wmanIf2BsOfdmaCtBasedResvTimeout, wmanIf2BsOfdmaBwReqOppSize, wmanIf2BsOfdmaRangReqOppSize, wmanIf2BsOfdmaUplinkCenterFreq, wmanIf2BsOfdmaInitRngCodes, wmanIf2BsOfdmaPeriodicRngCodes, wmanIf2BsOfdmaBWReqCodes, wmanIf2BsOfdmaPerRngBackoffStart, wmanIf2BsOfdmaPerRngBackoffEnd, wmanIf2eBsOfdmaStartOfRngCodes, wmanIf2BsOfdmaPermutationBase, wmanIf2BsOfdmaULAllocSubchBitmap, wmanIf2BsOfdmaOptPermULAllocSubchBitmap, wmanIf2BsOfdmaBandAMCAllocThreshold, wmanIf2BsOfdmaBandAMCReleaseThreshold, wmanIf2BsOfdmaBandAMCAllocTimer, wmanIf2BsOfdmaBandAMCReleaseTimer, wmanIf2BsOfdmaBandStatRepMAXPeriod, wmanIf2BsOfdmaBandAMCRetryTimer, wmanIf2BsOfdmaSafetyChAllocThreshold, wmanIf2BsOfdmaSafetyChReleaseThreshold, wmanIf2BsOfdmaSafetyChAllocTimer, wmanIf2BsOfdmaSafetyChReleaseTimer, wmanIf2BsOfdmaBinStatRepMAXPeriod, wmanIf2BsOfdmaSafetyChaRetryTimer, wmanIf2BsOfdmaHARQAackDelayULBurst, wmanIf2BsOfdmaCQICHBandAMCTranaDelay, wmanIf2BsOfdmaBsEIRP, wmanIf2BsOfdmaChannelNumber, wmanIf2BsOfdmaTTG, wmanIf2BsOfdmaRTG, wmanIf2BsOfdmaInitRngMaxRSS, wmanIf2BsOfdmaDownlinkCenterFreq, wmanIf2BsOfdmaBsId, wmanIf2BsOfdmaMacVersion, wmanIf2BsOfdmaFrameDurationCode, wmanIf2BsOfdmaSizeCqichIdField, wmanIf2BsOfdmaHARQAackDelayBurst, wmanIf2BsOfdmaUcdFecCodeType, wmanIf2BsOfdmaRangingDataRatio, wmanIf2BsOfdmaNorCOverNOverride, wmanIf2BsOfdmaUcdBurstProfileRowStatus, wmanIf2BsOfdmaDownlinkFrequency, wmanIf2BsOfdmaDcdFecCodeType, wmanIf2BsOfdmaDiucMandatoryExitThresh, wmanIf2BsOfdmaDiucMinEntryThresh, wmanIf2BsOfdmaDcdBurstProfileRowStatus} STATUS current DESCRIPTION "This group contains objects for BS and OFDMA PHY." ::= { wmanIf2MibGroups 8 } wmanIf2MibSsOfdmaGroup OBJECT-GROUP OBJECTS {wmanIf2SsOfdmaCtBasedResvTimeout, wmanIf2SsOfdmaBwReqOppSize, wmanIf2SsOfdmaRangReqOppSize, wmanIf2SsOfdmaUplinkCenterFreq, wmanIf2SsOfdmaInitRngCodes, wmanIf2SsOfdmaPeriodicRngCodes, wmanIf2SsOfdmaBWReqCodes, wmanIf2SsOfdmaPerRngBackoffStart, wmanIf2SsOfdmaPerRngBackoffEnd, wmanIf2SsOfdmaStartOfRngCodes, wmanIf2SsOfdmaPermutationBase, wmanIf2SsOfdmaULAllocSubchBitmap, wmanIf2SsOfdmaOptPermULAllocSubchBitmap, wmanIf2SsOfdmaBandAMCAllocThreshold, wmanIf2SsOfdmaBandAMCReleaseThreshold, wmanIf2SsOfdmaBandAMCAllocTimer, wmanIf2SsOfdmaBandAMCReleaseTimer, wmanIf2SsOfdmaBandStatRepMAXPeriod, wmanIf2SsOfdmaBandAMCRetryTimer, wmanIf2SsOfdmaSafetyChAllocThreshold, wmanIf2SsOfdmaSafetyChReleaseThreshold, wmanIf2SsOfdmaSafetyChAllocTimer, wmanIf2SsOfdmaSafetyChReleaseTimer, wmanIf2SsOfdmaBinStatRepMAXPeriod, wmanIf2SsOfdmaSafetyChaRetryTimer, wmanIf2SsOfdmaHARQAackDelayULBurst, wmanIf2SsOfdmaCQICHBandAMCTranaDelay, wmanIf2SsOfdmaBsEIRP, wmanIf2SsOfdmaChannelNumber, wmanIf2SsOfdmaTTG, wmanIf2SsOfdmaRTG, wmanIf2SsOfdmaInitRngMaxRSS, wmanIf2SsOfdmaDownlinkCenterFreq, wmanIf2SsOfdmaBsId, wmanIf2SsOfdmaMacVersion, wmanIf2SsOfdmaFrameDurationCode, wmanIf2SsOfdmaSizeCqichIdField, wmanIf2SsOfdmaHARQAackDelayBurst, wmanIf2SsOfdmaUiucIndex, wmanIf2SsOfdmaUcdFecCodeType, wmanIf2SsOfdmaRangingDataRatio, wmanIf2SsOfdmaNorCOverNOverride, wmanIf2SsOfdmaDiucIndex, wmanIf2SsOfdmaDownlinkFrequency, wmanIf2SsOfdmaDcdFecCodeType, wmanIf2SsOfdmaDiucMandatoryExitThresh, wmanIf2SsOfdmaDiucMinEntryThresh} STATUS current DESCRIPTION "This group contains objects for SS and OFDMA PHY." ::= { wmanIf2MibGroups 9 } wmanIf2MibBsNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS {wmanIf2BsSsStatusNotificationTrap, wmanIf2BsSsDynamicServiceFailTrap, wmanIf2BsSsRssiStatusChangeTrap, wmanIf2BsSsPkmFailTrap, wmanIf2BsSsRegistrerTrap} STATUS current DESCRIPTION "This group contains event notifications for BS." ::= { wmanIf2MibGroups 10 } wmanIf2MibSsNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS {wmanIf2SsTlvUnknownTrap, wmanIf2SsDynamicServiceFailTrap, wmanIf2SsDhcpSuccessTrap, wmanIf2SsRssiStatusChangeTrap} STATUS current DESCRIPTION "This group contains event notifications for SS." ::= { wmanIf2MibGroups 11 } wmanIf2MibCmnPhsGroup OBJECT-GROUP OBJECTS {-- Payload header supression wmanIf2CmnPhsRulePhsField, wmanIf2CmnPhsRulePhsMask, wmanIf2CmnPhsRulePhsSize, wmanIf2CmnPhsRulePhsVerify} STATUS current DESCRIPTION "This group contains common objects for PHS." ::= { wmanIf2MibGroups 12 } wmanIf2MibBsPhsGroup OBJECT-GROUP OBJECTS {-- Payload header supression wmanIf2BsClassifierRulePhsSize, wmanIf2BsClassifierRulePhsMask, wmanIf2BsClassifierRulePhsVerify, wmanIf2BsClassifierRuleBitMap} STATUS current DESCRIPTION "This group contains BS objects for PHS." ::= { wmanIf2MibGroups 13 } END