-- Title: ALVARION Private MIB -- This Private MIB supports BreezeAccessVL and BreezeNET B product lines. -- -- -- Version: 1.2.9 -- Date: Thursday October 30 2003 -- Comments: ALVARION agents also support the following Public MIBs: -- Some MIB compilers require that the following lines -- for proper compilation -- For parameters that are applicable to BreezeNET B products,BU functionality is the same as AU, -- RB functionality is the same as SU --#include "rfc1155.smi" --#include "rfc1212.smi" -- mgmt OBJECT IDENTIFIER ::= { iso org(3) dod(6) internet(1) mgmt(2) } -- mib OBJECT IDENTIFIER ::= { mgmt 1 } -- directory OBJECT IDENTIFIER ::= { internet 1 } -- experimental OBJECT IDENTIFIER ::= { internet 3 } -- private OBJECT IDENTIFIER ::= { internet 4 } -- enterprises OBJECT IDENTIFIER ::= { private 1 } -- End of lines which might be needed to other MIB browsers -- for proper compilation ALVARION-DOT11-WLAN-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, enterprises, IpAddress,Counter32,OBJECT-TYPE FROM SNMPv2-SMI TRAP-TYPE FROM RFC-1215; breezeAccessVLMib MODULE-IDENTITY LAST-UPDATED "0106041040Z" ORGANIZATION "Alvarion, Ltd." CONTACT-INFO " Klara Milman Postal: Alvarion, LTD HaBarzel 21a 69710 ISRAEL Tel: 972-3-7674554 Fax: 972-3-6498875 E-mail: klara.milman@alvarion.com." DESCRIPTION "breeze Access VL MIB Definitions - Release 1.2.0" -- REVISION "24062002000" -- DESCRIPTION ::= { products 1 } MacAddress ::= OCTET STRING (SIZE(6)) DisplayString ::= OCTET STRING alvarion OBJECT IDENTIFIER ::= { enterprises 12394 } products OBJECT IDENTIFIER ::= { alvarion 1 } alvarionOID OBJECT IDENTIFIER ::= { alvarion 4 } brzAccessVLOID OBJECT IDENTIFIER ::= { alvarionOID 1 } brzAccessVLAU OBJECT IDENTIFIER ::= { brzAccessVLOID 1 } brzAccessVLSU OBJECT IDENTIFIER ::= { brzAccessVLOID 2 } brzAccessVLAU-BS OBJECT IDENTIFIER ::= { brzAccessVLOID 4 } brzAccessVLAU-SA OBJECT IDENTIFIER ::= { brzAccessVLOID 5 } brzAccessVLSU-6-1D OBJECT IDENTIFIER ::= { brzAccessVLOID 11 } brzAccessVLSU-6-BD OBJECT IDENTIFIER ::= { brzAccessVLOID 12 } brzAccessVLSU-24-BD OBJECT IDENTIFIER ::= { brzAccessVLOID 13 } brzAccessVLSU-BD OBJECT IDENTIFIER ::= { brzAccessVLOID 14 } brzNetB-BU-B14 OBJECT IDENTIFIER ::= { brzAccessVLOID 21 } brzNetB-BU-B28 OBJECT IDENTIFIER ::= { brzAccessVLOID 22 } brzNetB-RB-B14 OBJECT IDENTIFIER ::= { brzAccessVLOID 31 } brzNetB-RB-B28 OBJECT IDENTIFIER ::= { brzAccessVLOID 32 } brzAccessVLProducts OBJECT IDENTIFIER ::= { brzAccessVLOID 3 } -- **************************************************************************************** -- **************************************************************************************** -- General System Info -- =================== brzaccVLSysInfo OBJECT IDENTIFIER ::= {breezeAccessVLMib 1} brzaccVLUnitHwVersion OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU and SU. Read-only. Hardware platform version." ::= { brzaccVLSysInfo 1 } brzaccVLRunningSoftwareVersion OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU and SU. Read-only. Running software version." ::= { brzaccVLSysInfo 2 } brzaccVLRunningFrom OBJECT-TYPE SYNTAX INTEGER { mainVersion(1) , shadowVersion(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU and SU. Read-only. The memory (main or shadow) from which the current version is running from" ::= { brzaccVLSysInfo 3 } brzaccVLMainVersionNumber OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU and SU. Read-only. Main software version number." ::= { brzaccVLSysInfo 4 } brzaccVLMainVersionFileName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU and SU. Read-only. Main software version file name." ::= { brzaccVLSysInfo 5 } brzaccVLShadowVersionNumber OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU and SU. Read-only. Shadow software version number." ::= { brzaccVLSysInfo 6 } brzaccVLShadowVersionFileName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU and SU. Read-only. Shadow software version file name." ::= { brzaccVLSysInfo 7 } brzaccVLUnitMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU and SU. Read-only. Unit hardware MAC address." ::= { brzaccVLSysInfo 8 } brzaccVLUnitType OBJECT-TYPE SYNTAX INTEGER {auBS (1), auSA(2) , su-6-1D(3),su-6-BD(4),su-24-BD(5),bu-B14(6),bu-B28(7),rb-B14(8),rb-B28(9),su-BD(10) } MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU and SU. Read-only. auBS (1) : AU-BS (modular access unit). auSA (2) : AU-SA (stand-alone access unit). su-6-1D (3): SU-6-1D (subscriber unit supporting 6 Mbps) su-6-BD(4) : SU-6-BD (subscriber unit supporting 6 Mbps). su-24-BD(5): SU-24-BD (subscriber unit supporting 24 Mbps). bu-B14(6) : BU-B14 (BreezeNET Base Unit supporting 14 Mbps). bu-B28(7) : BU-B28 (BreezeNET Base Unit supporting 28 Mbps). rb-B14(8) : RB-B14 (BreezeNET Remote Bridge supporting 14 Mbps). rb-B28(9) : RB-B28 (BreezeNET Remote Bridge supporting 28 Mbps). su-BD(10) : SU-BD (subscriber unit)." ::= { brzaccVLSysInfo 9 } brzaccVLAssociatedAU OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU only. Read-only. Associated AU MAC address." ::= { brzaccVLSysInfo 10 } brzaccVLNumOfAssociationsSinceLastReset OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU and SU. Read-only. The number of associations since last reset, including duplicate associations (re-associations)." ::= { brzaccVLSysInfo 11 } brzaccVLCurrentNumOfAssociations OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU only. Read-only. Not applicable to BreezeNET B products. The number of subscriber units currently associated with the AU. BreezeNET B products return 65535." ::= { brzaccVLSysInfo 13 } brzaccVLUnitBootVersion OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU and SU. Read-only. Boot version." ::= { brzaccVLSysInfo 14 } brzaccVLRadioBand OBJECT-TYPE SYNTAX INTEGER {band-5-8GHz (1), band-5-4GHz (2) , band-4-9GHz (3)} MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU and SU. Read-only. The unit's radio band." ::= { brzaccVLSysInfo 15 } brzaccVLCurrentEthernetPortState OBJECT-TYPE SYNTAX INTEGER { halfDuplexAnd10Mbps (1), fullDuplexAnd10Mbps (2), halfDuplexAnd100Mbps (3), fullDuplexAnd100Mbps (4), linkDown (5) } MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU and SU. Read-only. The current Ethernet port state." ::= { brzaccVLSysInfo 16 } brzaccVLTimeSinceLastReset OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU and SU. Read-only. The elapsed time since last reset." ::= { brzaccVLSysInfo 17 } -- Unit Control -- ============ brzaccVLUnitControl OBJECT IDENTIFIER ::= {breezeAccessVLMib 2} brzaccVLResetUnit OBJECT-TYPE SYNTAX INTEGER { cancel (1), resetSystemNow (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. Resets the unit and applies new parameter values." ::= { brzaccVLUnitControl 1 } brzaccVLSetDefaults OBJECT-TYPE SYNTAX INTEGER { completeFactory (1), partialFactory (2), completeOperator (3), partialOperator (4), cancel(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. Sets unit configuration to Defaults values after the next reset. completeFactory : All parameters revert to Factory Defaults values. partialFactory : All parameters revert to Factory Defaults values, except the parameters required for maintaining wireless connectivity. completeOperator: All parameters revert to Operator Defaults values. partialOperator : All parameters revert to Operator Defaults values, except the parameters required for maintaining wireless connectivity." ::= { brzaccVLUnitControl 2 } brzaccVLUnitName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. The unit name. A string of up to 32 printable ASCII characters." ::= { brzaccVLUnitControl 3 } brzaccVLFlashMemoryControl OBJECT-TYPE SYNTAX INTEGER { resetAndBootFromShadowVersion (1), useRunningVersionAfterReset (2),cancel(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. resetAndBootFromShadowVersion : Activates the backup version. useRunningVersionAfterReset : The currently active version will become the main version and will be activated after next reset." ::= { brzaccVLUnitControl 4 } brzaccVLTelnetLogoutTimer OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. Time-out of management via Telnet program. Automatic exit if the program is inactive for the defined time. Range: 1 to 999 (minutes)." ::= { brzaccVLUnitControl 5 } brzaccVLSaveCurrentConfigurationAsOperatorDefaults OBJECT-TYPE SYNTAX INTEGER { saveAsDefaults (1),cancel(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. Saves the current configuration as Operator Defaults." ::= { brzaccVLUnitControl 6 } brzaccVLExitTelnet OBJECT-TYPE SYNTAX INTEGER { cancelOperation (1), exit (2)} MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. Exit the management via Telnet program." ::= { brzaccVLUnitControl 7 } brzaccVLUnitPasswords OBJECT IDENTIFIER ::= {brzaccVLUnitControl 8} brzaccVLReadOnlyPassword OBJECT-TYPE SYNTAX DisplayString (SIZE(8)) MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. The User (read only) password. Up to 8 printable ASCII characters." ::= { brzaccVLUnitPasswords 1 } brzaccVLInstallerPassword OBJECT-TYPE SYNTAX DisplayString (SIZE(8)) MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. The Installer password. Up to 8 printable ASCII characters." ::= { brzaccVLUnitPasswords 2 } brzaccVLAdminPassword OBJECT-TYPE SYNTAX DisplayString (SIZE(8)) MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. The Administrator password. This is also the Write Community String. Up to 8 printable ASCII characters." ::= { brzaccVLUnitPasswords 3 } brzaccVLEthernetNegotiationMode OBJECT-TYPE SYNTAX INTEGER { force10MbpsAndHalfDuplex (1), force10MbpsAndFullDuplex (2), force100MbpsAndHalfDuplex (3), force100MbpsAndFullDuplex (4), autoNegotiationMode (5) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. The speed/duplex mode of the Ethernet port." ::= { brzaccVLUnitControl 9 } brzaccVLFTPParameters OBJECT IDENTIFIER ::= {brzaccVLUnitControl 10} brzaccVLFTPServerParams OBJECT IDENTIFIER ::= {brzaccVLFTPParameters 1} brzaccVLFTPServerUserName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..18)) MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. The user name to be used for access to the FTP server. " ::= { brzaccVLFTPServerParams 1 } brzaccVLFTPServerPassword OBJECT-TYPE SYNTAX DisplayString (SIZE(0..18)) MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. The password to be used for access to the FTP server." ::= { brzaccVLFTPServerParams 2 } brzaccVLFTPClientIPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. The IP address of the FTP stack in the unit." ::= { brzaccVLFTPServerParams 3 } brzaccVLFTPServerIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. The IP address of the FTP server." ::= { brzaccVLFTPServerParams 4 } brzaccVLFTPClientMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. The Mask of the FTP stack in the unit." ::= { brzaccVLFTPServerParams 5 } brzaccVLFTPGatewayIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. The FTP Gateway address" ::= { brzaccVLFTPServerParams 6 } brzaccVLFTPSwDownload OBJECT IDENTIFIER ::= {brzaccVLFTPParameters 2} brzaccVLFTPSwFileName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..20)) MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. The name of the SW file to be downloaded." ::= { brzaccVLFTPSwDownload 1 } brzaccVLFTPSwSourceDir OBJECT-TYPE SYNTAX DisplayString (SIZE(0..80)) MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. The source directory of the required file in the FTP server. Up to 80 printable ASCII characters. Use dot (.) To clear field" ::= { brzaccVLFTPSwDownload 2 } brzaccVLFTPDownloadSwFile OBJECT-TYPE SYNTAX INTEGER { downloadFile (1) , cancel (2)} MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. Execution of the SW download operation" ::= { brzaccVLFTPSwDownload 3 } brzaccVLConfigurationFileLoading OBJECT IDENTIFIER ::= {brzaccVLFTPParameters 3} brzaccVLConfigurationFileName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..20)) MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. The name of the configuration file to be downloaded/uploaded." ::= { brzaccVLConfigurationFileLoading 1 } brzaccVLOperatorDefaultsFileName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..20)) MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. The name of the Operator Defaults file to be downloaded/uploaded" ::= { brzaccVLConfigurationFileLoading 2 } brzaccVLFTPConfigurationFileSourceDir OBJECT-TYPE SYNTAX DisplayString (SIZE(0..80)) MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. The source directory of the required file in the FTP server. Up to 80 printable ASCII characters. Use dot (.) To clear field" ::= { brzaccVLConfigurationFileLoading 3 } brzaccVLExecuteFTPConfigurationFileLoading OBJECT-TYPE SYNTAX INTEGER {executeFTPGetConfigurationFile (1), executeFTPPutConfigurationFile (2), executeFTPGetOperatorDefaults (3) , executeFTPPutOperatorDefaults (4), cancel (5) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. Execution of the file download/upload operation." ::= { brzaccVLConfigurationFileLoading 4 } brzaccVLEventLogFileUploading OBJECT IDENTIFIER ::= {brzaccVLFTPParameters 4} brzaccVLEventLogFileName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..20)) MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. The name of the Event Log file to be uploaded." ::= { brzaccVLEventLogFileUploading 1 } brzaccVLEventLogDestinationDir OBJECT-TYPE SYNTAX DisplayString (SIZE(0..80)) MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. The destination directory of the event log file. Up to 80 printable ASCII characters. Use dot (.) To clear field" ::= { brzaccVLEventLogFileUploading 2 } brzaccVLUploadEventLogFile OBJECT-TYPE SYNTAX INTEGER { uploadFile (1) , cancel (2)} MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. Execution of the event log upload operation" ::= { brzaccVLEventLogFileUploading 3 } brzaccVLLoadingStatus OBJECT-TYPE SYNTAX INTEGER {inProcess (1), successful (2), failed (3)} MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU and SU. The status of the last loading operation." ::= { brzaccVLUnitControl 11 } brzaccVLEventLogFileParams OBJECT IDENTIFIER ::= {brzaccVLUnitControl 12} brzaccVLEventLogPolicy OBJECT-TYPE SYNTAX INTEGER {message (1), warning (2), error (3),fatal(4), logNone(5)} MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. The lowest level event to be registered in the event log.." ::= { brzaccVLEventLogFileParams 1 } brzaccVLEraseEventLog OBJECT-TYPE SYNTAX INTEGER { eraseEventLog (1),cancel(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. Erase the event log." ::= { brzaccVLEventLogFileParams 2 } -- Network Management Params -- ========================= brzaccVLNwMngParameters OBJECT IDENTIFIER ::= {breezeAccessVLMib 3} brzaccVLAccessToNwMng OBJECT-TYPE SYNTAX INTEGER { fromWirelessOnly (1), fromEthernetOnly (2), fromBothWirelessAndEthernet (3), na (255) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. The port to be used for remote management." ::= { brzaccVLNwMngParameters 1 } brzaccVLNwMngFilter OBJECT-TYPE SYNTAX INTEGER { disable (1), activateOnEthernetPort (2), activateOnWirelessPort (3), activateOnBothWirelessAndEthernet (4), na (255) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. Disables or enable on one of the ports, or on both ports, IP address based filtering of management messages (e.g. SNMP , Telnet , TFTP , DHCP)." ::= { brzaccVLNwMngParameters 2 } mngIpFilterTable OBJECT-TYPE SYNTAX SEQUENCE OF MngIpFilterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Applicable to AU and SU. A Management IP Filter Table of up to 3 IP addresses of devices that are authorized to access the unit for management purposes." ::= { brzaccVLNwMngParameters 3 } mngIpFilterEntry OBJECT-TYPE SYNTAX MngIpFilterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Applicable to AU and SU. A Management IP Filter Table entry." INDEX { brzaccVLNwMngIpTableIdx } ::= { mngIpFilterTable 1 } MngIpFilterEntry ::= SEQUENCE { brzaccVLNwMngIpAddress IpAddress, brzaccVLNwMngIpTableIdx INTEGER } brzaccVLNwMngIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. An IP address in the Management IP Filter Table." ::= { mngIpFilterEntry 1 } brzaccVLNwMngIpTableIdx OBJECT-TYPE SYNTAX INTEGER (1..8) MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU and SU. A table index for an entry in the Management IP Filter Table." ::= { mngIpFilterEntry 2 } brzaccVLDeleteOneNwIpAddr OBJECT-TYPE SYNTAX INTEGER { deleteFirstEntry (1), deleteSecondEntry (2), deleteThirdEntry (3), cancelOperation (4), na (255) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. Deletes a single selected entry from the Management IP Filter Table." ::= { brzaccVLNwMngParameters 4 } brzaccVLDeleteAllNwIpAddrs OBJECT-TYPE SYNTAX INTEGER { deleteAll (1), cancelOperation (2), na (255) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. Deletes all entries from the Management IP Filter Table." ::= { brzaccVLNwMngParameters 5 } brzaccVLAccessToNwTrap OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. Enables or disables sending of traps." ::= { brzaccVLNwMngParameters 6 } mngTrapTable OBJECT-TYPE SYNTAX SEQUENCE OF MngTrapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Applicable to AU and SU. A Management Trap Table of up to 3 IP addresses of stations to send traps to." ::= { brzaccVLNwMngParameters 7 } mngTrapEntry OBJECT-TYPE SYNTAX MngTrapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Applicable to AU and SU. A Management Trap Table entry." INDEX { brzaccVLNwTrapTableIdx } ::= { mngTrapTable 1 } MngTrapEntry ::= SEQUENCE { brzaccVLNwMngTrapCommunity DisplayString, brzaccVLNwMngTrapAddress IpAddress, brzaccVLNwTrapTableIdx INTEGER } brzaccVLNwMngTrapCommunity OBJECT-TYPE SYNTAX DisplayString (SIZE(0..14)) MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. The trap community associated with the applicable entry in the Management Trap Table. Up to 14 printable case sensitive ASCII characters." ::= { mngTrapEntry 1 } brzaccVLNwMngTrapAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. An IP address in the Management Trap Table entry." ::= { mngTrapEntry 2 } brzaccVLNwTrapTableIdx OBJECT-TYPE SYNTAX INTEGER (1..3) MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU and SU. Tables Index for an entry in the Management Trap Table." ::= { mngTrapEntry 3 } brzaccVLDeleteOneTrapAddr OBJECT-TYPE SYNTAX INTEGER { deletefirstEntry (1), deletesecondEntry (2), deletethirdEntry (3), cancelOperation (4), na (255) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. Deletes a single selected entry from the Management Trap Table." ::= { brzaccVLNwMngParameters 8 } brzaccVLDeleteAllTrapAddrs OBJECT-TYPE SYNTAX INTEGER { deleteAll (1),cancelOperation (2), na (255) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. Deletes all entries from the Management Trap Table." ::= { brzaccVLNwMngParameters 9 } -- IP Params: -- =========== brzaccVLIpParams OBJECT IDENTIFIER ::= {breezeAccessVLMib 4} brzaccVLUnitIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. IP address of the unit." ::= { brzaccVLIpParams 1 } brzaccVLSubNetMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. Subnet mask of the unit." ::= { brzaccVLIpParams 2 } brzaccVLDefaultGWAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. Default gateway IP address of the unit." ::= { brzaccVLIpParams 3 } brzaccVLUseDhcp OBJECT-TYPE SYNTAX INTEGER{ disable (1), dhcpOnly (2), automatic (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. DHCP client mode of operation. disabled : Use regular (manual) methods to configure IP parameters. dHCP Only: Use DHCP server to configure IP parameters. automatic: Use DHCP server to configure IP parameters. If a DHCP server is not available, use manually configured values." ::= { brzaccVLIpParams 4 } brzaccVLAccessToDHCP OBJECT-TYPE SYNTAX INTEGER{ fromWirelessOnly (1), fromEthernetOnly (2), fromBothWirelessAndEthernet (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. The port to be used for communicating with a DHCP server." ::= { brzaccVLIpParams 5 } brzaccVLRunTimeIPaddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU and SU. Read-only. The run-time IP address. If DHCP is used the Run Time IP Address is the address given to the unit by the server. Otherwise it is the manually configured address." ::= { brzaccVLIpParams 6 } brzaccVLRunTimeSubNetMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU and SU. Read-only. The run-time Subnet Mask. If DHCP is used the Run Time Subnet Mask is the mask given to the unit by the server. Otherwise it is the manually configured mask." ::= { brzaccVLIpParams 7 } brzaccVLRunTimeDefaultIPGateway OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU and SU. Read-only. The run-time Gateway IP address. If DHCP is used the Run Time Gateway IP Address is the address given to the unit by the server. Otherwise it is the manually configured address." ::= { brzaccVLIpParams 8 } -- Bridge Params -- ============== brzaccVLBridgeParameters OBJECT IDENTIFIER ::= {breezeAccessVLMib 5} brzaccVLVLANSupport OBJECT IDENTIFIER ::= {brzaccVLBridgeParameters 1} brzaccVLVlanID OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU only. VLAN ID for data frame tagging. Applicable to Access Link only. Range: 1-4094. 0 - not applicable." ::= { brzaccVLVLANSupport 1 } brzaccVLEthernetLinkType OBJECT-TYPE SYNTAX INTEGER { accessLink (1), trunkLink (2), hybridLink (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. VLAN support mode (Link Type). The Access Link option is not available for AU." ::= { brzaccVLVLANSupport 2 } brzaccVLManagementVlanID OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. VLAN ID for management frame tagging. Range: 1-4094, 65535 for No VLAN tagging." ::= { brzaccVLVLANSupport 3 } brzaccVLVLANForwarding OBJECT IDENTIFIER ::= {brzaccVLVLANSupport 4} brzaccVLVlanForwardingSupport OBJECT-TYPE SYNTAX INTEGER { disable (1) , enable (2), na(255) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. Enables or disables the VLAN forwarding feature. (applicable in Trunk links only)." ::= { brzaccVLVLANForwarding 1 } brzaccVLVlanForwardingTable OBJECT-TYPE SYNTAX SEQUENCE OF BrzaccVLVlanForwardingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Applicable to AU and SU. A VLAN Forwarding Table of up to 20 VLAN IDs of devices to which data frames are forwarded when VLAN Forwarding is Enabled. (applicable in Trunk links only). Not accessible." ::= { brzaccVLVLANForwarding 2 } brzaccVLVlanForwardingEntry OBJECT-TYPE SYNTAX BrzaccVLVlanForwardingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Applicable to AU and SU. A VLAN Forwarding Table entry. (applicable in Trunk links only). Not accessible." INDEX { brzaccVLVlanForwardingTableIdx } ::= { brzaccVLVlanForwardingTable 1 } BrzaccVLVlanForwardingEntry ::= SEQUENCE { brzaccVLVlanForwardingTableIdx INTEGER, brzaccVLVlanIdForwarding INTEGER } brzaccVLVlanForwardingTableIdx OBJECT-TYPE SYNTAX INTEGER (1..20) MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU and SU. A read only table index for a VLAN entry in the VLAN Forwarding Table." ::= { brzaccVLVlanForwardingEntry 1 } brzaccVLVlanIdForwarding OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. The list of VLAN ID's in the VLAN ID Forwarding Table. To Remove a VLAN ID - SET the corresponding entry to 0. To Add a new VLAN ID SET an entry which is currently 0. Range : 0..4094" ::= { brzaccVLVlanForwardingEntry 2 } brzaccVLVlanRelaying OBJECT IDENTIFIER ::= {brzaccVLVLANSupport 5} brzaccVLVlanRelayingSupport OBJECT-TYPE SYNTAX INTEGER { disable (1) , enable (2), na(255) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU only. Not applicable to BreezeNET B products. Enables or disables VLAN Relaying (applicable in Trunk links only)." ::= { brzaccVLVlanRelaying 1 } brzaccVLVlanRelayingTable OBJECT-TYPE SYNTAX SEQUENCE OF BrzaccVLVlanRelayingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Applicable to AU only. Not applicable to BreezeNET B products. A VLAN Relaying Table of up to 20 VLAN IDs of devices to which data frames are relayed when VLAN Relaying is Enabled. (applicable in Trunk links only). Not accessible." ::= { brzaccVLVlanRelaying 2 } brzaccVLVlanRelayingEntry OBJECT-TYPE SYNTAX BrzaccVLVlanRelayingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Applicable to AU only. Not applicable to BreezeNET B products. A VLAN Relaying Table entry. (applicable in Trunk links only). Not accessible." INDEX { brzaccVLVlanRelayingTableIdx } ::= { brzaccVLVlanRelayingTable 1 } BrzaccVLVlanRelayingEntry ::= SEQUENCE { brzaccVLVlanRelayingTableIdx INTEGER, brzaccVLVlanIdRelaying INTEGER } brzaccVLVlanRelayingTableIdx OBJECT-TYPE SYNTAX INTEGER (1..20) MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU only. Not applicable to BreezeNET B products. A read only table index for a VLAN entry in the VLAN Relaying Table." ::= { brzaccVLVlanRelayingEntry 1 } brzaccVLVlanIdRelaying OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU only. Not applicable to BreezeNET B products. The list of VLAN ID's in the VLAN ID Relaying Table. To Remove a VLAN ID - SET the corresponding entry to 0. To Add a new VLAN ID SET an entry which is currently 0. Range: 0-4094 , 0 - remove entry." ::= { brzaccVLVlanRelayingEntry 2 } brzaccVLVLANTrafficPriority OBJECT IDENTIFIER ::= {brzaccVLVLANSupport 6} brzaccVLVlanDataPriority OBJECT-TYPE SYNTAX INTEGER { na(255) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU only. Priority tagging for data frames. Applicable to Access Link only. Range: 0 to 7." ::= { brzaccVLVLANTrafficPriority 1 } brzaccVLVlanManagementPriority OBJECT-TYPE SYNTAX INTEGER { na(255) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. Priority tagging for management frames. Applicable to Access Link and Trunk Link only. Range: 0-7." ::= { brzaccVLVLANTrafficPriority 2 } brzaccVLVlanPriorityThreshold OBJECT-TYPE SYNTAX INTEGER { na(255) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. Priority threshold for tagged frames received from Ethernet port. Applicable to Hybrid Link and Trunk Link only. Valid values: 0-7." ::= { brzaccVLVLANTrafficPriority 3 } brzaccVLBridgeAgingTime OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. Bridge aging time for devices on both the Ethernet and wireless link sides. Range: 20 to 2000 seconds." ::= { brzaccVLBridgeParameters 2 } brzaccVLBroadcastRelaying OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2), na (255) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU only. Not applicable to BreezeNET B products. Enables/disables the relaying of broadcast messages to the wireless link." ::= { brzaccVLBridgeParameters 4 } brzaccVLUnicastRelaying OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2), na (255) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU only. Not applicable to BreezeNET B products. Enables/disables the relaying of unicast messages to the wireless link." ::= { brzaccVLBridgeParameters 5 } brzaccVLEthBroadcastFiltering OBJECT-TYPE SYNTAX INTEGER { disable (1), onEthernetOnly (2), onWirelessOnly (3), onBothWirelessAndEthernet (4), na (255) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU only. Enables/disables the filtering of Ethernet (layer2) broadcasts. disable : No filtering. onEthernetOnly : Filters broadcasts received on the Ethernet port only. onWirelessOnly : Filters broadcasts received on the Wlan port only. onBothWirelessAndEth: Filters broadcasts received on both ports." ::= { brzaccVLBridgeParameters 6 } brzaccVLEthBroadcastingParameters OBJECT IDENTIFIER ::= {brzaccVLBridgeParameters 7} brzaccVLDHCPBroadcastOverrideFilter OBJECT-TYPE SYNTAX INTEGER { disable (1), enable (2), na (255) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU only. Enables or disables the broadcasting of DHCP messages, overriding the general *brzaccVLEthBroadcastFiltering Ethernet broadcast filtering option." ::= { brzaccVLEthBroadcastingParameters 1 } brzaccVLPPPoEBroadcastOverrideFilter OBJECT-TYPE SYNTAX INTEGER { disable (1), enable (2), na (255) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU only. Enables or disables the broadcasting of PPPoE messages, overriding the general *brzaccVLEthBroadcastFiltering Ethernet broadcast filtering option." ::= { brzaccVLEthBroadcastingParameters 2 } brzaccVLARPBroadcastOverrideFilter OBJECT-TYPE SYNTAX INTEGER { disable (1), enable (2), na (255) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU only. Enables or disables the broadcasting of ARP messages, overriding the general *brzaccVLEthBroadcastFiltering Ethernet broadcast filtering option." ::= { brzaccVLEthBroadcastingParameters 3 } brzaccVLToSPriorityParameters OBJECT IDENTIFIER ::= {brzaccVLBridgeParameters 8} brzaccVLToSPrecedenceThreshold OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU and AU . Priority threshold (based on the ToS) for frames received from the Ethernet port. Range: 0-7." ::= { brzaccVLToSPriorityParameters 1 } -- brzaccVLRoamingSnapOption OBJECT-TYPE -- SYNTAX INTEGER { disable (0), enable (1), na (255) } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "Applicable to SU only. -- Disable/enable the roaming snap feature." -- ::= { brzaccVLBridgeParameters 9 } -- Air Interface Params -- ===================== brzaccVLAirInterface OBJECT IDENTIFIER ::= {breezeAccessVLMib 6} brzaccVLESSIDParameters OBJECT IDENTIFIER ::= {brzaccVLAirInterface 1} brzaccVLESSID OBJECT-TYPE SYNTAX DisplayString (SIZE(0..31)) MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU and AU. The Extended Service Set ID (ESSID) used to prevent the merging of collocated systems. The ESSID is accessible only with the write community string (administrator password). Up to 31 printable case sensitive ASCII characters." ::= { brzaccVLESSIDParameters 1 } brzaccVLOperatorESSIDOption OBJECT-TYPE SYNTAX INTEGER {disable (1) , enable (2), na (255) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU only. Enabling/disabling the use of the Operator ESSID." ::= { brzaccVLESSIDParameters 2 } brzaccVLOperatorESSID OBJECT-TYPE SYNTAX DisplayString (SIZE(0..31)) MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU only. A secondary ESSID to support easy installation of SUs as well as the use of the Best AU feature. Accessible only with SNMP Write Community Up to 31 printable case sensitive ASCII characters." ::= { brzaccVLESSIDParameters 3} brzaccVLRunTimeESSID OBJECT-TYPE SYNTAX DisplayString (SIZE(31)) MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU only. The ESSID of the associated AU. Accessible only with SNMP Write Community. Up to 31 printable ASCII characters, case sensitive." ::= { brzaccVLESSIDParameters 4 } brzaccVLMaximumCellRadius OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. For AU : read-write. The highest distance from the AU of any SU served by it. Affects the maximum time the AU and the SUs served by it wait for a response message and the slot size by taking into account the round trip propagation delay. For SU : read only. The distance learned from the AU . Range : 0 - 50,000" ::= { brzaccVLAirInterface 2 } brzaccVLAIFS OBJECT-TYPE SYNTAX INTEGER { oneSlot (1), twoSlots (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. Arbitration Inter-Frame Spacing (AIFS) value, in slots." ::= { brzaccVLAirInterface 3 } brzaccVLWirelessTrapThreshold OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU only. A wireless link quality threshold, expressed in % of retransmissions, for sending the brzaccVLAUWirelessQualityTRAP. This trap indicate whether the quality has gone below or above the specified threshold. The Threshold Range: 1-100 (% retransmissions)." ::= { brzaccVLAirInterface 4 } brzaccVLTransmitPowerTable OBJECT-TYPE SYNTAX SEQUENCE OF BrzaccVLTransmitPowerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Applicable to AU and SU. A table of transmit power parameters. " ::= { brzaccVLAirInterface 5} brzaccVLTransmitPowerEntry OBJECT-TYPE SYNTAX BrzaccVLTransmitPowerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Applicable to AU and SU. An entry in the Transmit Power Table." INDEX { brzaccVLTransmitPowerIdx } ::= { brzaccVLTransmitPowerTable 1 } BrzaccVLTransmitPowerEntry ::= SEQUENCE { brzaccVLTransmitPowerIdx INTEGER, brzaccVLApplicableModulationLevel INTEGER, brzaccVLMaximumTxPowerRange DisplayString, brzaccVLTxPower DisplayString, brzaccVLCurrentTxPower DisplayString } brzaccVLTransmitPowerIdx OBJECT-TYPE SYNTAX INTEGER (1..4) MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU and SU. An index of an entry in the Transmit Power Table." ::= { brzaccVLTransmitPowerEntry 1 } brzaccVLApplicableModulationLevel OBJECT-TYPE SYNTAX INTEGER {level1to5 (1), level6 (2), level7 (3),level8 (4)} MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU and SU. The applicable modulation level for an entry in the Transmit Power Table. Level 8 is not applicable to units with HW revision A." ::= { brzaccVLTransmitPowerEntry 2 } brzaccVLMaximumTxPowerRange OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU and SU. The allowed range for the brzaccVLTxPower parameter at the applicable modulation level . Range: -10 to the maximum allowed power level at the applicable modulation level , in dBm." ::= { brzaccVLTransmitPowerEntry 3 } brzaccVLTxPower OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. In AU: The transmit power in dBm defined for the applicable rate. In SU: If ATPC is disabled, this is the transmit power in dBm defined for the applicable rate. If ATPC is enabled, it serves as the initial transmit power in dBm for the ATPC algorithm. In SU: The range is -10 dBm to the power value defined by brzaccVLMaximumTxPower for the applicable modulation level. In AU: The range is -10 dBm to the power value defined by brzaccVLMaximumTxPowerRange for the applicable modulation level." ::= { brzaccVLTransmitPowerEntry 4 } brzaccVLCurrentTxPower OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU. The actual transmit power in dBm for the applicable rate. Range: -17 to the maximum value defined by brzaccVLMaximumTxPowerRange for the applicable modulation level." ::= { brzaccVLTransmitPowerEntry 5 } brzaccVLMaximumTransmitPowerTable OBJECT-TYPE SYNTAX SEQUENCE OF BrzaccVLMaximumTransmitPowerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Applicable to SU only. A table of maximum transmit power parameters. " ::= { brzaccVLAirInterface 6} brzaccVLMaximumTransmitPowerEntry OBJECT-TYPE SYNTAX BrzaccVLMaximumTransmitPowerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Applicable and SU. An entry in the Maximum Transmit Power Table." INDEX { brzaccVLMaximumTransmitPowerIdx } ::= { brzaccVLMaximumTransmitPowerTable 1 } BrzaccVLMaximumTransmitPowerEntry ::= SEQUENCE { brzaccVLMaximumTransmitPowerIdx INTEGER, brzaccVLMaxTxApplicableModulationLevel INTEGER, brzaccVLDefinedMaximumTxPowerRange DisplayString, brzaccVLMaxTxPower DisplayString } brzaccVLMaximumTransmitPowerIdx OBJECT-TYPE SYNTAX INTEGER (1..4) MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU only. An index of an entry in the Maximum Transmit Power Table." ::= { brzaccVLMaximumTransmitPowerEntry 1 } brzaccVLMaxTxApplicableModulationLevel OBJECT-TYPE SYNTAX INTEGER {level1to5 (1), level6 (2), level7 (3),level8 (4)} MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU only. The applicable modulation level for an entry in the Maximum Transmit Power Table. Level 8 is not applicable to units with HW revision A." ::= { brzaccVLMaximumTransmitPowerEntry 2 } brzaccVLDefinedMaximumTxPowerRange OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU only. The allowed range for the brzaccVLMaxTxPower parameter at the applicable modulation level . Range: -10 to the maximum allowed power level at the applicable modulation level , in dBm." ::= { brzaccVLMaximumTransmitPowerEntry 3 } brzaccVLMaxTxPower OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU only. The maximum value that can be configured for the brzaccVLTxPower parameter. This is also the maximum power level that can be reached by the ATPC algorithm. The range is -10 dBm to the maximum value defined by brzaccVLDefinedMaximumTxPowerRange for the applicable modulation level." ::= { brzaccVLMaximumTransmitPowerEntry 4 } brzaccVLMaxNumOfAssociations OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU only. Not applicable to BreezeNET B products. Sets the upper limit for the number of Subscriber Units that can be associated with the AU. Range: 0 -512. BreezeNET B products return 65535." ::= { brzaccVLAirInterface 10 } brzaccVLBestAu OBJECT IDENTIFIER ::= {brzaccVLAirInterface 11} brzaccVLBestAuSupport OBJECT-TYPE SYNTAX INTEGER { disable (1), enable (2), na (255) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU only. Disable/enable the Best AU selection mechanism." ::= { brzaccVLBestAu 1 } brzaccVLBestAuNoOfScanningAttempts OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU only. The number of scanning attempts to collect information for the Best AU decision. Range: 1 to 255." ::= { brzaccVLBestAu 2 } brzaccVLPreferredAuMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU only. The MAC address of the preferred AU (overriding the Best AU selection process). 000000000000 means no preferred AU." ::= { brzaccVLBestAu 3 } brzaccVLNeighborAuTable OBJECT-TYPE SYNTAX SEQUENCE OF BrzaccVLNeighborAuEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Applicable to SU only. A table of data on neighboring AUs." ::= { brzaccVLBestAu 4} brzaccVLNeighborAuEntry OBJECT-TYPE SYNTAX BrzaccVLNeighborAuEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Applicable to SU only. An entry in the Neighbor AU Table." INDEX { brzaccVLNeighborAuIdx } ::= { brzaccVLNeighborAuTable 1 } BrzaccVLNeighborAuEntry ::= SEQUENCE { brzaccVLNeighborAuIdx INTEGER, brzaccVLNeighborAuMacAdd MacAddress, brzaccVLNeighborAuESSID DisplayString, brzaccVLNeighborAuSNR INTEGER, brzaccVLNeighborAuAssocLoadStatus INTEGER, brzaccVLNeighborAuMark INTEGER } brzaccVLNeighborAuIdx OBJECT-TYPE SYNTAX INTEGER (1..20) MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU only. An index of an entry in the Neighbor AU Table." ::= { brzaccVLNeighborAuEntry 1 } brzaccVLNeighborAuMacAdd OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU only. A MAC address of an AU in the Neighbor AU Table." ::= { brzaccVLNeighborAuEntry 2 } brzaccVLNeighborAuESSID OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU only. The ESSID of an AU in the Neighbor AU Table. Accessible only with SNMP Write Community." ::= { brzaccVLNeighborAuEntry 3 } brzaccVLNeighborAuSNR OBJECT-TYPE SYNTAX INTEGER { na (255) } MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU only. The received signal quality (SNR) in dB of an AU in the Neighbor AU Table." ::= { brzaccVLNeighborAuEntry 4 } brzaccVLNeighborAuAssocLoadStatus OBJECT-TYPE SYNTAX INTEGER { full (1),notFull (2), na (255) } MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU only. Neighbor AU association load status in the Neighbor AU Table." ::= { brzaccVLNeighborAuEntry 5 } brzaccVLNeighborAuMark OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU only. Neighbor AU mark in the Neighbor AU Table." ::= { brzaccVLNeighborAuEntry 6 } brzaccVLFrequencyDefinition OBJECT IDENTIFIER ::= {brzaccVLAirInterface 12} brzaccVLSubBandLowerFrequency OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU only. The lowest frequency in the subset to be used for scanning. For 5.8GHz products the range is 5740 to 5830 MHz using 10MHz resolution. For 4.9GHz products the range is 4920 to 5080 MHz using 10MHz resolution" ::= { brzaccVLFrequencyDefinition 1 } brzaccVLSubBandUpperFrequency OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU only. The highest frequency in the subset to be used for scanning. For 5.8GHz products the range is 5740 to 5830 MHz using 10MHz resolution. For 4.9GHz products the range is 4920 to 5080 MHz using 10MHz resolution" ::= { brzaccVLFrequencyDefinition 2 } brzaccVLScanningStep OBJECT-TYPE SYNTAX INTEGER { mhz-10(2) , mhz-20(3)} MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU only. The scanning step to be used for generating the frequency subset" ::= { brzaccVLFrequencyDefinition 3 } brzaccVLFrequencySubsetTable OBJECT-TYPE SYNTAX SEQUENCE OF BrzaccVLFrequencySubsetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Applicable to SU only. The Frequency Subset Table that includes all frequencies from the Sub-band Lower Frequency to the Sub-band Upper Frequency, using steps as defined by the Scanning Step." ::= { brzaccVLFrequencyDefinition 4 } brzaccVLFrequencySubsetEntry OBJECT-TYPE SYNTAX BrzaccVLFrequencySubsetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Applicable to SU only. An entry in the Frequency Subset Table. " INDEX { brzaccVLFrequencySubsetTableIdx } ::= { brzaccVLFrequencySubsetTable 1 } BrzaccVLFrequencySubsetEntry ::= SEQUENCE { brzaccVLFrequencySubsetTableIdx INTEGER, brzaccVLFrequencySubsetFrequency INTEGER, brzaccVLFrequencySubsetActive INTEGER } brzaccVLFrequencySubsetTableIdx OBJECT-TYPE SYNTAX INTEGER (1..40) MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU only. An index of an entry in the Frequency subset Table." ::= { brzaccVLFrequencySubsetEntry 1 } brzaccVLFrequencySubsetFrequency OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU only. A frequency of an entry in the Frequency subset Table." ::= { brzaccVLFrequencySubsetEntry 2 } brzaccVLFrequencySubsetActive OBJECT-TYPE SYNTAX INTEGER {active (1) , notActive (2)} MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU only. The status of an entry in the Frequency subset Table. The frequency of an active entry will be included in the final list of frequencies to be used for scanning." ::= { brzaccVLFrequencySubsetEntry 3 } brzaccVLSetSelectedFreqSubset OBJECT-TYPE SYNTAX INTEGER {setSelectedFreqsSubset(1) ,cancel (2)} MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU only. Apply the selected subset. After the next reset the new subset will be used for scanning." ::= { brzaccVLFrequencyDefinition 5 } brzaccVLCurrentFrequencySubsetTable OBJECT-TYPE SYNTAX SEQUENCE OF BrzaccVLCurrentFrequencySubsetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Applicable to SU only. The Current Frequency Subset table that includes all frequencies that are currently used for scanning." ::= { brzaccVLFrequencyDefinition 6 } brzaccVLCurrentFrequencySubsetEntry OBJECT-TYPE SYNTAX BrzaccVLCurrentFrequencySubsetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Applicable to SU only. An entry in the Current Frequency Subset Table. " INDEX { brzaccVLCurrentFrequencySubsetTableIdx } ::= { brzaccVLCurrentFrequencySubsetTable 1 } BrzaccVLCurrentFrequencySubsetEntry ::= SEQUENCE { brzaccVLCurrentFrequencySubsetTableIdx INTEGER, brzaccVLCurrentFrequencySubsetFrequency INTEGER } brzaccVLCurrentFrequencySubsetTableIdx OBJECT-TYPE SYNTAX INTEGER (1..40) MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU only. An index of an entry in the Current Frequency subset Table." ::= { brzaccVLCurrentFrequencySubsetEntry 1 } brzaccVLCurrentFrequencySubsetFrequency OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU only. A frequency of an entry in the Current Frequency subset Table." ::= { brzaccVLCurrentFrequencySubsetEntry 2 } brzaccVLCurrentAUOperatingFrequency OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU only. The operating frequency of the AU. For 5.8GHz products the range is 5740 to 5830 MHz using 10MHz resolution. For 4.9GHz products the range is 4920 to 5080 MHz using 10MHz resolution." ::= { brzaccVLFrequencyDefinition 7 } brzaccVLAUDefinedFrequency OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU only. The frequency of the AU after the next reset. For 5.8GHz products the range is 5740 to 5830 MHz using 10MHz resolution. For 4.9GHz products the range is 4920 to 5080 MHz using 10MHz resolution." ::= { brzaccVLFrequencyDefinition 8 } brzaccVLCurrentSUOperatingFrequency OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU only. The frequency used currently by the unit. For 5.8GHz products the range is 5740 to 5830 MHz using 10MHz resolution. For 4.9GHz products the range is 4920 to 5080 MHz using 10MHz resolution." ::= { brzaccVLFrequencyDefinition 9 } brzaccVLATPC OBJECT IDENTIFIER ::= {brzaccVLAirInterface 13} brzaccVLAtpcOption OBJECT-TYPE SYNTAX INTEGER { disable (1) , enable (2) , na (255) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable AU and SU. Enabling/disabling the ATPC Algorithm." ::= { brzaccVLATPC 1 } brzaccVLDeltaFromMinSNRLevel OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable AU only. The Minimum SNR Level plus the value of this parameter define the maximum desired level of the average SNR at the AU. If the ATPC Option is enabled, than if the received SNR is above the maximum desired level, the AU will transmit Power-Down messages to the applicable SU. Range: 4 to 20 (dB)." ::= { brzaccVLATPC 2 } brzaccVLMinimumSNRLevel OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable AU only. Defines the minimum desired level of the average SNR at the AU. Below this level, if *AtpcOption is enabled, the AU will transmit ATPC Power-Up messages to the applicable SU. The *MinimumSNRLevel cannot be higher than *MaximumSNRLevel. Range: 4 to 60 (dB)." ::= { brzaccVLATPC 3 } brzaccVLMinimumIntervalBetweenATPCMessages OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable AU only. The minimum interval between two consecutive AU to SU messages. Range: 1 to 3600 (Sec)." ::= { brzaccVLATPC 4 } brzaccVLPowerLevelSteps OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable AU only. The step in dB that the SU will use when receiving an ATPC Power-Up/Power-Down message Range: 1 to 20 (dB)." ::= { brzaccVLATPC 6 } -- Service Params -- ============== brzaccVLServiceParameters OBJECT IDENTIFIER ::= {breezeAccessVLMib 7} -- brzaccVLMirCirOption OBJECT-TYPE -- SYNTAX INTEGER {disable (1), -- enable (2), -- na (255)} -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "Applicable to AU and SU. Read-only in SU. -- The setting in the AU enables/disables the MIR/CIR support -- feature for all SUs served by the AU." -- ::= { brzaccVLServiceParameters 1 } brzaccVLMirDownlink OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU only. Sets the Maximum Information Rate (MIR) from AU to SU. MIR must be above brzaccVLCirDownlink value. Range for set: 128 - 4000 (Kbps) for SU-6, 128 - 15,000 (Kbps) for SU-24, 128-54,000 for SU-BD, 128 - 7,000 for RB-14, 128 - 14,000 for RB-28. The actual value (Get) will be the entered value rounded to the nearest multiple of 128 (N*128)." ::= { brzaccVLServiceParameters 2 } brzaccVLMirUplink OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU only. Sets the Maximum Information Rate (MIR) from SU to AU. MIR must be above brzaccVLCirUplink value. Range for set: 128 - 4000 (Kbps) for SU-6, 128 - 15,000 (Kbps) for SU-24, 128-54,000 for SU-BD, 128 - 7,000 for RB-14, 128 - 14,000 for RB-28. The actual value (Get) will be the entered value rounded to the nearest multiple of 128 (N*128)." ::= { brzaccVLServiceParameters 3 } brzaccVLCirDownlink OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU only. Sets the Committed Information Rate (CIR) from AU to SU. CIR must be below brzaccVLMirDownlink value. Range for Set: 0 - 4,000 (Kbps) for SU-6, 0 - 15,000 (Kbps) for SU-24, 0-54,000 for SU-BD. The actual value (Get) will be the entered value rounded to the nearest multiple of 128 (N*128). BrrezeNET B products will return 65535. " ::= { brzaccVLServiceParameters 4 } brzaccVLCirUplink OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU only. Not applicable to BreezeNET B products Sets the Committed Information Rate (CIR) from SU to AU. CIR must be below brzaccVLMirUplink value. Range for Set: 0 - 4,000 (Kbps) for SU-6, 0 - 15,000 (Kbps) for SU-24, 0-54,000 for SU-BD. The actual value (Get) will be the entered value rounded to the nearest multiple of 128 (N*128). BrrezeNET B products will return 65535." ::= { brzaccVLServiceParameters 5 } brzaccVLMaxDelay OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU only. Not applicable to BreezeNET B products Sets the maximal time packets may be delayed by the CIR\MIR mechanism. Above the configured maximal period the packets are discarded. Range: 300 - 10000 milliseconds. BreezeNET B products return 65535." ::= { brzaccVLServiceParameters 6 } brzaccVLMaxBurstDuration OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. Not applicable to BreezeNET B products Sets the maximum time during which inactivity bonus time can be accumulated for future burst transmissions. Range: 0 - 2000 mili seconds. BreezeNET B products return 65535" ::= { brzaccVLServiceParameters 7 } brzaccVLGracefulDegradationLimit OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU only. Not applicable to BreezeNET B products. Sets the maximum limit for activating the graceful degradation algorithm. Range: 0 - 70% rate of the CIR. BreezeNET B products return 255." ::= { brzaccVLServiceParameters 8 } brzaccVLMirOnlyOption OBJECT-TYPE SYNTAX INTEGER {disable (1), enable (2), na (255)} MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU only. Not applicable to BreezeNET B products. When brzaccMirOnly is enabled, it overrides the CIR/MIR algorithm for determining actual information rate and forces the algorithm to operate with MIR parameter settings only. When enabled, the Graceful Degradation algorithm is disabled." ::= { brzaccVLServiceParameters 9 } -- User Filtering Params -- ===================== brzaccVLUserFilterParams OBJECT IDENTIFIER ::= {breezeAccessVLMib 8} brzaccVLUserFilterOption OBJECT-TYPE SYNTAX INTEGER { disable (1), ipOnly (2), userDefinedAddrOnly (3), pPPoEOnly (4), na (255) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU only. Defines user-filtering options. disable: No filtering. iPOnly: Only IP protocol frames pass. userDefinedAddrOnly: Only ip frames to/from user defined IP addresses pass. pPPoE Only: Only PPPoE frames pass." ::= { brzaccVLUserFilterParams 1 } brzaccVLIpFilterTable OBJECT-TYPE SYNTAX SEQUENCE OF BrzaccVLIpFilterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Applicable to SU only. An IP Filter Table of up to 8 user defined addresses, or address groups, to be used if the selected User Filtering option is userDefinedAddrOnly." ::= { brzaccVLUserFilterParams 2 } brzaccVLIpFilterEntry OBJECT-TYPE SYNTAX BrzaccVLIpFilterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Applicable to SU only. An IP Filter Table entry." INDEX { brzaccVLIpFilterIdx } ::= { brzaccVLIpFilterTable 1 } BrzaccVLIpFilterEntry ::= SEQUENCE { brzaccVLIpID IpAddress, brzaccVLMaskID IpAddress, brzaccVLIpFilterRange INTEGER, brzaccVLIpFilterIdx INTEGER } brzaccVLIpID OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU only. An IP address of an IP Filter Table entry." ::= { brzaccVLIpFilterEntry 1 } brzaccVLMaskID OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU only. An IP Mask of an IP Filter Table entry. Either a mask or a range, but not both can be used to define an address group. If the range is other than 0, than the mask is ignored and only the range value is used to define the address group." ::= { brzaccVLIpFilterEntry 2 } brzaccVLIpFilterRange OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU only. An addresses range for the IP Filter Table entry. The first address in the range is the IP address. O means that the range is not used. Either a mask or a range, but not both can be used to define an address group. If the range is other than 0, than the mask is ignored and only the range value is used to define the address group. Range: 0-255." ::= { brzaccVLIpFilterEntry 3 } brzaccVLIpFilterIdx OBJECT-TYPE SYNTAX INTEGER (1..8) MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU only. Read-only. A table index for the IP Filter Table entry." ::= { brzaccVLIpFilterEntry 4 } brzaccVLDeleteOneUserFilter OBJECT-TYPE SYNTAX INTEGER { deletefirstEntry (1), deletesecondEntry (2), deletethirdEntry (3), deletefourthEntry (4), deletefifthEntry (5), deletesixthEntry (6), deleteseventhEntry(7), deleteeighthEntry (8), cancelOperation (9), na (255) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU only. Deletes a single selected entry from the IP Filter Table." ::= { brzaccVLUserFilterParams 3 } brzaccVLDeleteAllUserFilters OBJECT-TYPE SYNTAX INTEGER { deleteAll (1), cancelOperation (2), na (255) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU only. Deletes all entries from the IP Filter Table." ::= { brzaccVLUserFilterParams 4 } -- Security Params -- ================== brzaccVLSecurityParameters OBJECT IDENTIFIER ::= {breezeAccessVLMib 9} brzaccVLAuthenticationAlgorithm OBJECT-TYPE SYNTAX INTEGER {openSystem(1) , sharedKey(2)} MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU and AU. Enables/disables the authentication encryption option. openSystem: Authentication messages are not encrypted. sharedKey : Authentication messages are encrypted " ::= { brzaccVLSecurityParameters 1 } brzaccVLSUDefaultKeyID OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU only. The key to be used for encryption of authentication messages and/or data. Range: 1 to 4. " ::= { brzaccVLSecurityParameters 2 } brzaccVLDataEncryptionOption OBJECT-TYPE SYNTAX INTEGER {disable(1) , enable(2)} MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU and AU. Enables/disables the data encryption option. " ::= { brzaccVLSecurityParameters 3 } brzaccVLAUDefaultMulticastKeyID OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU only. The key to be used for encryption of multicasts and broadcasts." ::= { brzaccVLSecurityParameters 4 } brzaccVLSecurityMode OBJECT-TYPE SYNTAX INTEGER {wep(1) , aes(2)} MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU and AU. The encryption algorithm to be used for authentication messages and/or data encryption" ::= { brzaccVLSecurityParameters 5 } brzaccVLAuthenticationPromiscuousMode OBJECT-TYPE SYNTAX INTEGER {disable(1) , enable(2)} MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU only. Enables/disable the promiscuous mode allowing authentication of and communication with all SUs regardless of their security parameters." ::= { brzaccVLSecurityParameters 6 } brzaccVLKey1 OBJECT-TYPE SYNTAX DisplayString (SIZE(32)) MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU and AU. Key number 1. Accessible only with SNMP Write Community String (administrator password). Valid values: 32 hexadecimal digits." ::= { brzaccVLSecurityParameters 7 } brzaccVLKey2 OBJECT-TYPE SYNTAX DisplayString (SIZE(32)) MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU and AU. Key number 2. Accessible only with SNMP Write Community String (administrator password). Valid values: 32 hexadecimal digits." ::= { brzaccVLSecurityParameters 8 } brzaccVLKey3 OBJECT-TYPE SYNTAX DisplayString (SIZE(32)) MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU and AU. Key number 3. Accessible only with SNMP Write Community String (administrator password). Valid values: 32 hexadecimal digits." ::= { brzaccVLSecurityParameters 9 } brzaccVLKey4 OBJECT-TYPE SYNTAX DisplayString (SIZE(32)) MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU and AU. Key number 4. Accessible only with SNMP Write Community String (administrator password). Valid values: 32 hexadecimal digits." ::= { brzaccVLSecurityParameters 10 } -- Performance Params -- ================== brzaccVLPerformanceParams OBJECT IDENTIFIER ::= {breezeAccessVLMib 10} brzaccVLRTSThreshold OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU and AU. Not applicable to BreezeNET B products. The minimum frame size that requires an RTS/CTS handshake. Range: 20 to 1600 bytes. BreezeNET B products return 65535." ::= { brzaccVLPerformanceParams 1 } brzaccVLMinContentionWindow OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU and AU. Not applicable to BreezeNET B products. The initial value to be used by the contention window calculation algorithm. Value must be 0 or power of 2 minus 1 (7,15,31...). Range: 0 to 1023, excluding 1 and 3. BreezeNET B products return 65535." ::= { brzaccVLPerformanceParams 3 } brzaccVLMaxContentionWindow OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU and AU. Not applicable to BreezeNET B products. The maximum value to be used by the contention window calculation algorithm. Value must be power of 2 minus 1 (7,15,31...) Range: 7 to 1023. BreezeNET B products return 65535" ::= { brzaccVLPerformanceParams 4 } brzaccVLMaximumModulationLevel OBJECT-TYPE SYNTAX INTEGER { level1 (1), level2 (2), level3 (3), level4 (4), level5 (5), level6 (6), level7 (7), level8 (8) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU and AU. If the Adaptive Modulation algorithm is enabled, it sets the Maximum Modulation Level to be used. If The Modulation algorithm is disabled, it sets the Fixed Modulation Level to be used. The range is 1 to 8. 8 is not applicable for units with HW revision A." ::= { brzaccVLPerformanceParams 5 } brzaccVLMulticastModulationLevel OBJECT-TYPE SYNTAX INTEGER { level1 (1), level2 (2), level3 (3), level4 (4), level5 (5), level6 (6), level7 (7), level8 (8) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU only. The modulation level for multicast and broadcast data frames. The range is 1 to 8. 8 is not applicable for units with HW revision A." ::= { brzaccVLPerformanceParams 6 } brzaccVLAvgSNRMemoryFactor OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable AU only. The weight of history in average SNR calculation. The higher is the value, the higher is the weight of history. Range: -1 (Disregard History) to 32." ::= { brzaccVLPerformanceParams 7 } brzaccVLHardwareRetries OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU and AU. The maximum number of trials to transmit an unacknowledged frame in each Hardware Retrial phase. Range : 1 to 15." ::= { brzaccVLPerformanceParams 8 } brzaccVLAdaptiveModulationParams OBJECT IDENTIFIER ::= {brzaccVLPerformanceParams 9} brzaccVLAdaptiveModulationAlgorithmOption OBJECT-TYPE SYNTAX INTEGER { disable (1) , enable (2), na (255) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU and AU. Enables/disables the adaptive modulation level decision mechanism." ::= { brzaccVLAdaptiveModulationParams 1 } brzaccVLSoftwareRetrySupport OBJECT-TYPE SYNTAX INTEGER { disable (1) , enable (2), na (255) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU and AU. Enabling/disabling the Software Retry mechanism when the Adaptive Modulation algorithm is enabled." ::= { brzaccVLAdaptiveModulationParams 2 } brzaccVLNumOfSoftwareRetries OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU and AU. The maximum number of times to use the Software Retry mechanism when it is enabled. Range : 1 to 14" ::= { brzaccVLAdaptiveModulationParams 3 } brzaccVLMinIntervalBetweenAdaptiveModulationAlgorithmMessages OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable AU and SU. The minimum interval between two consecutive AU to SU messages. Range: 1 to 3600 (Sec)." ::= { brzaccVLAdaptiveModulationParams 4 } brzaccVLBurstMode OBJECT IDENTIFIER ::= {brzaccVLPerformanceParams 10} brzaccVLBurstModeOption OBJECT-TYPE SYNTAX INTEGER { disable (1) , enable (2), na (255) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enables/disable burst mode operation. Applicable only to BreezeNET B units (BU and RB) " ::= { brzaccVLBurstMode 1 } brzaccVLBurstInterval OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Burst mode interval in milliseconds. Applicable only to BreezeNET B units (BU and RB). Range: 1 to 10 (milliseconds). BreezeACCESS VL products return 255." ::= { brzaccVLBurstMode 2 } -- Site Survey Params -- ================== brzaccVLSiteSurvey OBJECT IDENTIFIER ::= {breezeAccessVLMib 11} brzaccVLAverageReceiveSNR OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU only. The average Signal to Noise Ratio of received frames." ::= { brzaccVLSiteSurvey 1 } -- Traffic Counters -- ================ brzaccVLTrafficStatistics OBJECT IDENTIFIER ::= {brzaccVLSiteSurvey 2} brzaccVLResetTrafficCounters OBJECT-TYPE SYNTAX INTEGER { reset (1),cancel(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to SU and AU. Resets the traffic counters." ::= { brzaccVLTrafficStatistics 1 } brzaccVLEthCounters OBJECT IDENTIFIER ::= {brzaccVLTrafficStatistics 2} brzaccVLWirelessLinkCounters OBJECT IDENTIFIER ::= {brzaccVLTrafficStatistics 3} brzaccVLWirelessLinkEvents OBJECT IDENTIFIER ::= {brzaccVLTrafficStatistics 4} brzaccVLPerModulationLevelCounters OBJECT IDENTIFIER ::= {brzaccVLTrafficStatistics 5} brzaccVLResetPerModulationLevelCounters OBJECT-TYPE SYNTAX INTEGER { resetCounters(1) , cancel (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU and SU. Resets the per-Modulation Level counters ." ::= { brzaccVLPerModulationLevelCounters 1 } brzaccVLSUPerModulationLevelCountersTable OBJECT-TYPE SYNTAX SEQUENCE OF BrzaccVLSUPerModulationLevelCountersEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Applicable to SU. Per Rate Counters table." ::= { brzaccVLPerModulationLevelCounters 2 } brzaccVLSUPerModulationLevelCountersEntry OBJECT-TYPE SYNTAX BrzaccVLSUPerModulationLevelCountersEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Applicable to SU. An entry in the Per modulation Counters table." INDEX { brzaccVLSUPerModulationLevelCountersTableIdx } ::= { brzaccVLSUPerModulationLevelCountersTable 1 } BrzaccVLSUPerModulationLevelCountersEntry ::= SEQUENCE { brzaccVLSUPerModulationLevelCountersTableIdx INTEGER, brzaccVLSUPerModulationLevelCountersApplicableModLevel INTEGER, brzaccVLSUPerModulationLevelCountersTxSuccess Counter32, brzaccVLSUPerModulationLevelCountersTxFailed Counter32 } brzaccVLSUPerModulationLevelCountersTableIdx OBJECT-TYPE SYNTAX INTEGER (1..8) MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU. An index of an entry in the Per modulation level Counters table." ::= { brzaccVLSUPerModulationLevelCountersEntry 1 } brzaccVLSUPerModulationLevelCountersApplicableModLevel OBJECT-TYPE SYNTAX INTEGER { modLevel-1 (1), modLevel-2 (2), modLevel-3 (3), modLevel-4 (4), modLevel-5 (5), modLevel-6 (6), modLevel-7 (7), modLevel-8 (8) } MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU. The applicable modulation level of the entry in the Per modulation level Counters table. Modulation Level 8 is not applicable for units with HW revision A." ::= { brzaccVLSUPerModulationLevelCountersEntry 2 } brzaccVLSUPerModulationLevelCountersTxSuccess OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU. The total number of successfully transmitted unicasts at the applicable modulation level." ::= { brzaccVLSUPerModulationLevelCountersEntry 3 } brzaccVLSUPerModulationLevelCountersTxFailed OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU. The total number of dropped frames at the applicable Modulation Level." ::= { brzaccVLSUPerModulationLevelCountersEntry 4 } brzaccVLTotalRxFramesViaEthernet OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU and AU. Total number of frames received via the Ethernet port." ::= { brzaccVLEthCounters 1 } brzaccVLTxWirelessToEthernet OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU and AU. Total number of frames transmitted to the Ethernet port." ::= { brzaccVLEthCounters 2 } brzaccVLTxFramesToWireless OBJECT IDENTIFIER ::= {brzaccVLWirelessLinkCounters 1} brzaccVLAUBeaconsToWireless OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU only. The number of beacons transmitted to the wireless media." ::= { brzaccVLTxFramesToWireless 1 } -- brzaccVLOtherMngFramesToWireless OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "Applicable to AU and SU. -- The number of management frames transmitted to the wireless media. -- In AU, this count does not include Beacons." -- ::= { brzaccVLTxFramesToWireless 2 } brzaccVLDataAndOtherMngFramesToWireless OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU only. The number of data and management frames transmitted to the wireless media. The count includes one count for each data frame transmitted successfully (excluding retransmissions)." ::= { brzaccVLTxFramesToWireless 3 } brzaccVLTotalTxFramesToWireless OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU and AU. The number of frames transmitted to the wireless media. The count includes one count for each data frame that was transmitted successfully (excluding retransmissions), and also the number of transmitted control and management frames, including beacons." ::= { brzaccVLTxFramesToWireless 4 } brzaccVLTotalTransmittedUnicasts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU only. Not applicable to BreezeNET B products. The total number of unicast frames successfully transmitted to the wireless media, excluding retransmissions." ::= { brzaccVLTxFramesToWireless 5 } brzaccVLTotalRxFramesFromWireless OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU and AU. The total number of frames that were received from the wireless media. The count includes data and control and management frames, including beacons received from the AU. The count does not include frames that were discarded internally, bad frames and duplicate frames." ::= { brzaccVLWirelessLinkCounters 2 } brzaccVLTotalRetransmittedFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU and AU. The total number of retransmissions of data frames (counts all unsuccessful transmissions/retransmissions)." ::= { brzaccVLWirelessLinkCounters 3 } brzaccVLFramesDropped OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU and AU. The number of dropped frames. The frames that were retransmitted to the extent of the maximum allowed number of retransmissions without being acknowledged.." ::= { brzaccVLWirelessLinkCounters 4 } brzaccVLDataFramesSubmittedToBridge OBJECT IDENTIFIER ::= {brzaccVLWirelessLinkCounters 5} brzaccVLFramesSubmittedViaHighQueue OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU and AU. Frames submitted to the internal bridge via the High priority queue. for transmission to the wireless media." ::= { brzaccVLDataFramesSubmittedToBridge 1 } brzaccVLFramesSubmittedViaMidQueue OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU and AU. Frames submitted to the internal bridge via the Mid priority queue for transmission to the wireless media." ::= { brzaccVLDataFramesSubmittedToBridge 2 } brzaccVLFramesSubmittedViaLowQueue OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU and AU. Frames submitted to the internal bridge via the Low priority queue for transmission to the wireless media." ::= { brzaccVLDataFramesSubmittedToBridge 3 } brzaccVLTotalNoOfDataFramesSubmitted OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU and AU. The total number of data frames submitted to the internal bridge for transmission to the wireless media." ::= { brzaccVLDataFramesSubmittedToBridge 4 } brzaccVLTotalRecievedDataFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU and AU. The total number of data frames received from the wireless media, including duplicate frames." ::= { brzaccVLWirelessLinkCounters 6 } brzaccVLRecievedBadFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU and AU. The number of frames received from the wireless media with errors (CRC errors)." ::= { brzaccVLWirelessLinkCounters 7 } brzaccVLNoOfDuplicateFramesDiscarded OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU and AU. The number of frames discarded due to receiving multiple copies." ::= { brzaccVLWirelessLinkCounters 8 } brzaccVLNoOfInternallyDiscardedMirCir OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU and AU. The number of data frames received from the Ethernet port that were discarded by the MIR/CIR mechanism to avoid exceeding the maximum allowed information rate." ::= { brzaccVLWirelessLinkCounters 9 } -- brzaccVLInternallyGeneratedFramesSubmittedToBridge OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "Applicable to SU and AU. Read-only. -- The number of internally generated frames(wireless management and control frames) -- submitted to the bridge for transmission to the wireless media." -- ::= { brzaccVLWirelessLinkCounters 10 } brzaccVLTxEvents OBJECT IDENTIFIER ::= {brzaccVLWirelessLinkEvents 1} brzaccVLDroppedFrameEvents OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU and AU. The number of frames that were dropped because they were retransmitted to the maximum allowed number of retransmissions without being acknowledged." ::= { brzaccVLTxEvents 1 } brzaccVLFramesDelayedDueToSwRetry OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU and AU. The number of frames that were delayed because the SW retry algorithm was activated on a previous frame designated for the same recipient." ::= { brzaccVLTxEvents 2 } brzaccVLUnderrunEvents OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU and AU. The number of frames whose transmission was aborted because the rate of submitting frames for transmission exceeded the available transmission capability." ::= { brzaccVLTxEvents 3 } brzaccVLOthersTxEvents OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU and AU. The number of Tx events due to problems other than those of the other Tx Events counters ." ::= { brzaccVLTxEvents 4 } brzaccVLTotalTxEvents OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU and AU. The total number of Tx special events." ::= { brzaccVLTxEvents 5 } brzaccVLRxEvents OBJECT IDENTIFIER ::= {brzaccVLWirelessLinkEvents 2} brzaccVLPhyErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU and AU. The number of frames that were not received properly due to a hardware problem." ::= { brzaccVLRxEvents 1 } brzaccVLCRCErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU and AU. The number of frames received from the wireless media containing CRC errors." ::= { brzaccVLRxEvents 2 } brzaccVLOverrunEvents OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU and AU. The number of frames that were discarded because the receive rate exceeded the processing capability or the capacity of the Ethernet port." ::= { brzaccVLRxEvents 3 } brzaccVLRxDecryptEvents OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU and AU. Read only. The number of frames that were not received properly due to a problem in the data decryption mechanism." ::= { brzaccVLRxEvents 4 } brzaccVLTotalRxEvents OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to SU and AU. The total number of Rx special events." ::= { brzaccVLRxEvents 5 } -- Associations Database -- brzaccVLMacAddressDatabase OBJECT IDENTIFIER ::= {brzaccVLSiteSurvey 5} brzaccVLAUMacAddressDatabase OBJECT IDENTIFIER ::= {brzaccVLMacAddressDatabase 1} brzaccVLAUAdbResetAllModulationLevelCounters OBJECT-TYPE SYNTAX INTEGER { reset (1), cancel (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable to AU only. To reset all the counters for all SUs in the MAC Address Database." ::= { brzaccVLAUMacAddressDatabase 1 } brzaccVLAUAdbTable OBJECT-TYPE SYNTAX SEQUENCE OF BrzaccVLAUAdbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Applicable to AU Only. AU MAC Address Database table." ::= { brzaccVLAUMacAddressDatabase 2 } brzaccVLAUAdbEntry OBJECT-TYPE SYNTAX BrzaccVLAUAdbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Applicable to AU Only. An entry in the AU MAC Address Database table." INDEX { brzaccVLAdbIndex } ::= { brzaccVLAUAdbTable 1 } BrzaccVLAUAdbEntry ::= SEQUENCE { brzaccVLAdbIndex INTEGER, brzaccVLAdbMacAddress MacAddress, brzaccVLAdbStatus INTEGER, brzaccVLAdbSwVersion DisplayString, brzaccVLAdbSNR INTEGER, brzaccVLAdbMaxModulationLevel INTEGER, brzaccVLAdbTxFramesTotal Counter32, brzaccVLAdbDroppedFramesTotal Counter32, brzaccVLAdbTxSuccessModLevel1 Counter32, brzaccVLAdbTxSuccessModLevel2 Counter32, brzaccVLAdbTxSuccessModLevel3 Counter32, brzaccVLAdbTxSuccessModLevel4 Counter32, brzaccVLAdbTxSuccessModLevel5 Counter32, brzaccVLAdbTxSuccessModLevel6 Counter32, brzaccVLAdbTxSuccessModLevel7 Counter32, brzaccVLAdbTxSuccessModLevel8 Counter32, brzaccVLAdbTxFailedModLevel1 Counter32, brzaccVLAdbTxFailedModLevel2 Counter32, brzaccVLAdbTxFailedModLevel3 Counter32, brzaccVLAdbTxFailedModLevel4 Counter32, brzaccVLAdbTxFailedModLevel5 Counter32, brzaccVLAdbTxFailedModLevel6 Counter32, brzaccVLAdbTxFailedModLevel7 Counter32, brzaccVLAdbTxFailedModLevel8 Counter32, brzaccVLAdbCirTx INTEGER, brzaccVLAdbMirTx INTEGER, brzaccVLAdbCirRx INTEGER, brzaccVLAdbMirRx INTEGER, brzaccVLAdbCirMaxDelay INTEGER } brzaccVLAdbIndex OBJECT-TYPE SYNTAX INTEGER (1..512) MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU Only. Read-only. The index of an entry in the AU MAC Address Database table." ::= { brzaccVLAUAdbEntry 1 } brzaccVLAdbMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU Only. The MAC Address of an SU entry in the MAC Address Database table." ::= { brzaccVLAUAdbEntry 2 } brzaccVLAdbStatus OBJECT-TYPE SYNTAX INTEGER { associated (1), authenticated (2), notAuthenticated (3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU Only. The status of the relevant SU." ::= { brzaccVLAUAdbEntry 3 } brzaccVLAdbSwVersion OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU only. The SW version of the relevant SU." ::= { brzaccVLAUAdbEntry 4 } brzaccVLAdbSNR OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU only. The average Signal to Noise Ratio in dB of frames received by the AU from the relevant SU." ::= { brzaccVLAUAdbEntry 5 } brzaccVLAdbMaxModulationLevel OBJECT-TYPE SYNTAX INTEGER { modLevel-1 (1), modLevel-2 (2), modLevel-3 (3), modLevel-4 (4), modLevel-5 (5), modLevel-6 (6), modLevel-7 (7), modLevel-8 (8) } MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU Only. The value configured in the relevant SU for the Maximum Modulation Level parameter. Modulation Level 8 is not applicable for units with HW revision A." ::= { brzaccVLAUAdbEntry 6 } brzaccVLAdbTxFramesTotal OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU Only. Counts the total number of unicast frames (excluding retransmissions) that were successfully transmitted to the SU over the wireless link." ::= { brzaccVLAUAdbEntry 7 } brzaccVLAdbDroppedFramesTotal OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU Only. Counts the total number of frames intended to the SU that were dropped because they were retransmitted to the extent of the maximum allowed number of retransmissions without being acknowledged." ::= { brzaccVLAUAdbEntry 8 } brzaccVLAdbTxSuccessModLevel1 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU Only. Read-only. Counts the total number of unicast frames (excluding retransmissions) that were successfully transmitted to the SU over the wireless link using modulation level 1." ::= { brzaccVLAUAdbEntry 9 } brzaccVLAdbTxSuccessModLevel2 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU Only. Read-only. Counts the total number of unicast frames (excluding retransmissions) that were successfully transmitted to the SU over the wireless link using modulation level 2." ::= { brzaccVLAUAdbEntry 10 } brzaccVLAdbTxSuccessModLevel3 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU Only. Read-only. Counts the total number of unicast frames (excluding retransmissions) that were successfully transmitted to the SU over the wireless link using modulation level 3." ::= { brzaccVLAUAdbEntry 11 } brzaccVLAdbTxSuccessModLevel4 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU Only. Read-only. Counts the total number of unicast frames (excluding retransmissions) that were successfully transmitted to the SU over the wireless link using modulation level 4." ::= { brzaccVLAUAdbEntry 12 } brzaccVLAdbTxSuccessModLevel5 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU Only. Read-only. Counts the total number of unicast frames (excluding retransmissions) that were successfully transmitted to the SU over the wireless link using modulation level 5." ::= { brzaccVLAUAdbEntry 13 } brzaccVLAdbTxSuccessModLevel6 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU Only. Read-only. Counts the total number of unicast frames (excluding retransmissions) that were successfully transmitted to the SU over the wireless link using modulation level 6." ::= { brzaccVLAUAdbEntry 14 } brzaccVLAdbTxSuccessModLevel7 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU Only. Read-only. Counts the total number of unicast frames (excluding retransmissions) that were successfully transmitted to the SU over the wireless link using modulation level 7." ::= { brzaccVLAUAdbEntry 15 } brzaccVLAdbTxSuccessModLevel8 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU Only. Read-only. Counts the total number of unicast frames (excluding retransmissions) that were successfully transmitted to the SU over the wireless link using modulation level 8. Not applicable for units with HW revision A." ::= { brzaccVLAUAdbEntry 16 } brzaccVLAdbTxFailedModLevel1 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU Only. Read-only. Counts the total number of failures to successfully transmit unicast frames intended to the SU using modulation level 1." ::= { brzaccVLAUAdbEntry 17 } brzaccVLAdbTxFailedModLevel2 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU Only. Read-only. Counts the total number of failures to successfully transmit unicast frames intended to the SU using modulation level 2." ::= { brzaccVLAUAdbEntry 18 } brzaccVLAdbTxFailedModLevel3 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU Only. Read-only. Counts the total number of failures to successfully transmit unicast frames intended to the SU using modulation level 3." ::= { brzaccVLAUAdbEntry 19 } brzaccVLAdbTxFailedModLevel4 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU Only. Read-only. Counts the total number of failures to successfully transmit unicast frames intended to the SU using modulation level 4." ::= { brzaccVLAUAdbEntry 20 } brzaccVLAdbTxFailedModLevel5 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU Only. Read-only. Counts the total number of failures to successfully transmit unicast frames intended to the SU using modulation level 5." ::= { brzaccVLAUAdbEntry 21 } brzaccVLAdbTxFailedModLevel6 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU Only. Read-only. Counts the total number of failures to successfully transmit unicast frames intended to the SU using modulation level 6." ::= { brzaccVLAUAdbEntry 22 } brzaccVLAdbTxFailedModLevel7 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU Only. Read-only. Counts the total number of failures to successfully transmit unicast frames intended to the SU using modulation level 7." ::= { brzaccVLAUAdbEntry 23 } brzaccVLAdbTxFailedModLevel8 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU Only. Read-only. Counts the total number of failures to successfully transmit unicast frames intended to the SU using modulation level 8. Not applicable for units with HW revision A." ::= { brzaccVLAUAdbEntry 24 } brzaccVLAdbCirTx OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU Only. Not applicable to BreezeNET B products. Read-only. The value configured in the relevant SU for the CIR: SU to AU parameter." ::= { brzaccVLAUAdbEntry 25 } brzaccVLAdbMirTx OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU Only. Read-only. The value configured in the relevant SU for the MIR: SU to AU parameter." ::= { brzaccVLAUAdbEntry 26 } brzaccVLAdbCirRx OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU Only.Not applicable to BreezeNET B products. Read-only. The value configured in the relevant SU for the CIR: AU to SU parameter." ::= { brzaccVLAUAdbEntry 27 } brzaccVLAdbMirRx OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU Only. Read-only. The value configured in the relevant SU for the MIR: AU to SU parameter." ::= { brzaccVLAUAdbEntry 28 } brzaccVLAdbCirMaxDelay OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU Only. Not applicable to BreezeNET B products. Read-only. The value configured in the relevant SU for the CIR Maximum Delay parameter." ::= { brzaccVLAUAdbEntry 29 } --brzaccVLSUMacAddressDatabase OBJECT IDENTIFIER ::= {brzaccVLMacAddressDatabase 2} -- -- --brzaccVLSUBridgingTable OBJECT-TYPE -- SYNTAX SEQUENCE OF brzaccVLSUBridgingEntry -- MAX-ACCESS not-accessible -- STATUS current -- DESCRIPTION -- "Applicable to SU Only. -- SU MAC Address Database table." -- ::= { brzaccVLSUMacAddressDatabase 1 } -- --brzaccVLSUBridgingEntry OBJECT-TYPE -- SYNTAX brzaccVLSUBridgingEntry -- MAX-ACCESS not-accessible -- STATUS current -- DESCRIPTION -- "Applicable to SU Only. -- An entry in the SU MAC Address Database table." -- INDEX { brzaccVLSUBridgingIndex } -- ::= { brzaccVLSUBridgingTable 1 } -- -- --brzaccVLSUBridgingEntry ::= SEQUENCE { -- brzaccVLSUBridgingIndex INTEGER, -- brzaccVLSUBridgingMacAddress MacAddress, -- brzaccVLSUBridgingLearnedFrom INTEGER -- } -- --brzaccVLSUBridgingIndex OBJECT-TYPE -- SYNTAX INTEGER -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "Applicable to SU Only. -- The index of an entry in the SU MAC Address Database table." -- ::= { brzaccVLSUBridgingEntry 1 } -- --brzaccVLSUBridgingMacAddress OBJECT-TYPE -- SYNTAX MacAddress -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "Applicable to SU Only." -- ::= { brzaccVLSUBridgingEntry 2 } -- --brzaccVLSUBridgingLearnedFrom OBJECT-TYPE -- SYNTAX INTEGER { wireless (1), -- ethernet (2) } -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "Applicable to SU Only. -- The port from which the relevant address was learned" -- ::= { brzaccVLSUBridgingEntry 3 } --brzaccVLAdbCurrentTxRate OBJECT-TYPE -- SYNTAX INTEGER -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "Applicable to AU Only. Read-only. -- The current transmit rate to the SU." -- ::= { brzaccVLAUAdbEntry 4 } -- -- **************************************************************************************** -- TRAP defenitions: -- **************************************************************************************** brzaccVLTraps OBJECT IDENTIFIER ::= { breezeAccessVLMib 14 } brzaccVLTrapSUMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU only. SU MAC Address." ::= { brzaccVLTraps 1 } --brzaccVLTrapSNRQuality OBJECT-TYPE -- SYNTAX INTEGER -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "Applicable to SU only. -- SNR of received signal." -- ::= { brzaccVLTraps 2 } brzaccVLTrapText OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Textual string for future use." ::= { brzaccVLTraps 3 } brzaccVLTrapToggle OBJECT-TYPE SYNTAX INTEGER{ on (1), off (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to all products. An On/Off toggle status." ::= { brzaccVLTraps 4 } brzaccVLTrapParameterChanged OBJECT-TYPE SYNTAX INTEGER{ ipFilter (2), vlan (4)} MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU and SU. A modification to one of the parameters related to IP Filtering or VLAN." ::= { brzaccVLTraps 5 } brzaccVLTrapAccessRights OBJECT-TYPE SYNTAX INTEGER{ notLoggedIn (1), readOnly (2), installer (3), administrator (4), factory (5) } MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to all products. The access rights used for login." ::= { brzaccVLTraps 6 } brzaccVLTrapLog OBJECT-TYPE SYNTAX INTEGER{ telnetLogin (3), telnetLogout (4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to all products. Login or logout to the Monitor program via Telnet." ::= { brzaccVLTraps 7 } brzaccVLTrapTelnetUserIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU and SU. The IP address of a Telnet user." ::= { brzaccVLTraps 8 } brzaccVLTrapRTx OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to AU only. Retransmissions as a percentage of total transmissions." ::= { brzaccVLTraps 9 } brzaccVLTrapFtpOrTftpStatus OBJECT-TYPE SYNTAX INTEGER{ successful (1), failed (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Applicable to all products. The status of the last FTP/TFTP loading procedure." ::= { brzaccVLTraps 10 } -- -- Private Traps for BreezeAccessVL -- brzaccVLSUassociatedAUTRAP TRAP-TYPE ENTERPRISE brzAccessVLProducts VARIABLES { brzaccVLTrapSUMacAddr -- SU MAC address } --&ACTIONS { log, minor, clrdups } --&MESG "New SU associated (SU Mac Address: $1)" DESCRIPTION "An AU trap indicating a new association with an SU." ::= 2 brzaccVLAUdisassociatedTRAP TRAP-TYPE ENTERPRISE brzAccessVLProducts VARIABLES { brzaccVLTrapSUMacAddr --Unit MAC address } DESCRIPTION "An AU trap indicating that an SU has been disassociated from the AU. The AU decides that an SU has been disassociated from it and remove it from the ADB after receiving from another AU a SNAP frame with the SU MAC address. The SNAP frame indicating a network topology change where the SU has associated with another AU will be received if both AUs are connected to the same Ethernet backbone" ::= 3 brzaccVLAUagingTRAP TRAP-TYPE ENTERPRISE brzAccessVLProducts VARIABLES { brzaccVLTrapSUMacAddr -- Unit MAC address } --&ACTIONS { log, minor, clrdups } --&MESG "Unit was aged out (SU Mac Address: $1)" DESCRIPTION "An AU trap indicating that the unit association was aged out and removed from the Associates SUs database following its failure to acknowledge a specified number of consecutive frames." ::= 4 brzaccVLSUassociatedTRAP TRAP-TYPE ENTERPRISE brzAccessVLProducts VARIABLES { -- brzaccVLLastAUMacAddress, Old AU mac address brzaccVLAssociatedAU -- New AU mac address -- brzaccVLTrapLastSNRQuality, Average SNR with old AU } --&ACTIONS { log, minor, clrdups } --&MESG "Associated with AU ( Mac Address $2)" DESCRIPTION "An SU trap indicating association with an AU. In addition to the MAC address information of the AU, the trap also includes information on the average SNR of frames received from the AU." ::= 6 brzaccVLAUwirelessQualityTRAP TRAP-TYPE ENTERPRISE brzAccessVLProducts VARIABLES { brzaccVLTrapToggle, brzaccVLTrapRTx } --&ACTIONS { log, major, clrdups } --&MESG "Quality of wireless link has been changed to $3" DESCRIPTION "An AU trap, indicating that the quality of the wireless link (retransmissions rate) has changed and dropped below (Off) or increased above (On) a threshold , defined by the *brzaccVLWirelessTrapThreshold. The threshold for AU is a percentage of retransmissions." ::= 20 brzaccVLPowerUpFromReset TRAP-TYPE ENTERPRISE brzAccessVLProducts VARIABLES { brzaccVLUnitMacAddress -- Unit MAC address } --&ACTIONS { log, minor, clrdups } --&MESG "Power Up From Reset (Unit Mac Address: $'1)" DESCRIPTION "An AU trap indicating power up after Reset." ::= 101 brzaccVLTelnetStatusTRAP TRAP-TYPE ENTERPRISE brzAccessVLProducts VARIABLES { brzaccVLTrapLog, brzaccVLTrapAccessRights, brzaccVLTrapTelnetUserIpAddress } --&ACTIONS { log, major, clrdups } --&MESG "$'1 With Access Rights $'3 (Telnet User Ip Address is $2)" DESCRIPTION "A trap indicating that a log-in or log-out has been performed via Telnet. Includes the log-in access right and the IP address of the PC performing Telnet." ::= 102 brzaccVLParameterChangedTRAP TRAP-TYPE ENTERPRISE brzAccessVLProducts VARIABLES { brzaccVLTrapParameterChanged } --&ACTIONS { log, major, clrdups } --&MESG "A $'1 Parameter Changed" DESCRIPTION "An AU or SU trap indicating a change in a IP Filter or VLAN parameter." ::= 103 brzaccVLLoadingStatusTRAP TRAP-TYPE ENTERPRISE brzAccessVLProducts VARIABLES { brzaccVLTrapFtpOrTftpStatus, brzaccVLUnitMacAddress } --&ACTIONS { log, major, clrdups } --&MESG "File Transfer to unit is finished" DESCRIPTION "A trap indicating that last FTP/TFTP loading process has been finished successfully or failed. " ::= 104 brzaccVLPromiscuousModeTRAP TRAP-TYPE ENTERPRISE brzAccessVLProducts VARIABLES { brzaccVLTrapToggle, brzaccVLUnitMacAddress } --&ACTIONS { log, major, clrdups } --&MESG "Promiscuous Mode change" DESCRIPTION "An AU trap, indicating that the AU In (On) Promiscuous Mode or out (Off) Promiscuous Mode." ::= 105 END